Fagor VTP 139 SL Manual de referencia

TAPAS REFRIGERATOR

Manual for installation, use, and maintenance

VTP 139 SL

VTP 175 SL

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page2

www.Fagorcommercial.com

Contents

1 RECEIVING AND INSPECTING THE EQUIPMENT.................................................................................... 3

2 SPECIFICATIONS .................................................................................................................................... 4

3 INSTALLATION....................................................................................................................................... 5

3.1 UNCRATING...................................................................................................................................... 5

3.2 LOCATION ........................................................................................................................................ 5

3.3 DATA PLATE...................................................................................................................................... 6

3.4 LEVELING.......................................................................................................................................... 6

3.5 ELECTRICAL CONNECTIONS.............................................................................................................. 6

4 OPERATION ........................................................................................................................................... 7

4.1 ELECTRONIC CONTROL..................................................................................................................... 7

4.2 OTHER FUNCTIONS ........................................................................................................................ 10

5 MAINTENANCE.................................................................................................................................... 11

5.1 CLEANING THE CONDENSER COIL..................................................................................................11

5.2 GASKET........................................................................................................................................... 12

5.3 DOORS/HINGES..............................................................................................................................12

5.4 DRAIN.............................................................................................................................................12

6 TROUBLE SHOOTING...........................................................................................................................14

7 WIRING DIAGRAMS............................................................................................................................. 15

8 WARRANTY..........................................................................................................................................16

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page3

www.Fagorcommercial.com

1RECEIVING AND INSPECTING THE EQUIPMENT

Up on receiving your new Fagor Refrigerator, check the package and the machine for any

damages that may have occurred during transportation. Visually inspect the exterior of the

package. I f damaged, open and inspect the contents with the carrier. Any damage should be

noted and reported on the delivering carrier’s receipt.

In the event that the exterior is not damaged, yet up on opening, there is concealed damage to

the equipment notify, the carrier immediately. Notification should be made verbally as well as

in written form. Request an inspection by the shipping company of the damaged equipment.

Retain all crating material until inspection has been made. Contact the dealer through which

you purchased the unit.

Check the compressor compartment thousing and visually inspect the refrigeration package.

Be sure lines are secure and base is still intact.

A NOTE FROM OUR QUALITY CONTROL MANAGER

CONGRATULATIONS ON YOUR NEW PURCHASE. WE WOULD LIKE TO WELCOME

YOU TO THE FAGOR TEAM. THE UNIT IN FRONT OF YOU IS A GREAT PIECE OF

EQUIPMENT THAT WILL BECOME ONE OF YOUR MOST RELAIBLE TOOLS IN YOUR

DAILY OPERATIONS FOR YEARS TO COME!

PRIOR TO SHIPPING YOUR UNIT, OUR TRAINED SERVICE TECHNICIANS TESTED

YOUR UNIT FOR A PERIOD OF 12 HOURS. THIS PERFORMANCE TEST WAS

RECORDED AND A COPY OF THE RESULTS IS INCLUDED WITH THIS SERVICE

MANUAL. DURING THIS TEST, OUR HIGHLY QUALIFIED PERSONNEL INSPECTED

YOUR MACHINE FOR LEAKS, LOSE COMPONENTS, AND IMPROPER NOISE

LEVELS. WE ALSO TESTED THE COOLING PERFORMANCE IN AN EFFORT TO GIVE

YOU THE BEST AND MOST RELAIBLE UNIT POSSIBLE.

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page4

www.Fagorcommercial.com

2SPECIFICATIONS

Note:

* The pressure in the suction line is recommended at 32°C/90°F maximum of ambient

temperature.

** Superheat measured in the outlet of the evaporator at 32°C/90°F

Model

Trays

Amps

Voltage

Plug

Type

BTU

Refrigerant

charge (oz)

Refrigerant

VTP 139 SL

2.3

1/6

120

5-15P

850

6.7

134 A

VTP 175 SL

2.3

1/6

120

5-15P

850

6.7

134 A

Voltage 115 60 Hz

Model

Trays

Amps

Voltage

Plug

Type

BTU

Refrigerant

charge (oz)

Refrigerant

VTP 139 SL

2.1

1/4

220

5-15P

850

6.7

134 A

VTP 175 SL

2.1

1/4

220

5-15P

850

6.7

134 A

Voltage 220 60 Hz

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page5

www.Fagorcommercial.com

3INSTALLATION

3.1 UNCRATING

Remove the outer packaging. Cut the 4 clamps that hold the refrigerator to the skid. Lift the

unit off the skid.

If machine was laid down during this operation, remember to leave the cabinet

up right for 24 hours before connecting to power source.

3.2 LOCATION

Units represented in this manual are intended for indoor use only. Be sure the location chosen

has a floor strong enough to support the total weight of the unit and its contents. For the most

efficient operation, be sure to provide at least three (3) inches between sides, back and top of

the unit.

THE MACHINES NEEDS TO BE INSTALLED 2 FEET AWAY FROM ANY HEAT SOURCES.

The unit should not be installed under ambient temperatures higher than 100 °F.

If the relative humidity is higher than 60 %, the door frames may sweat water. This is not a

malfunctioning of the unit.

WARNING

The following actions will void your warranty:

-Modification of power cord.

-Connecting the unit to any extension cord.

-Neglecting to install the castors or optional legs.

Inside cabinet:

The first cleaning must happen when you unpack the unit and before it is turned ON. For

this, you have to clean the unit with warm water and mild detergent. When it is cleaned and

dry, proceed to install accessories and plug your unit into a dedicated outlet. WAIT 24 HOURS

BEFORE PLACING PRODUCT IN THE UNIT. This will guarantee that it is working properly.

Consequential damages are not covered under warranty.

Outside cabinet:

Be sure that the unit has access to ample air to breathe. Avoid hot corners and locations near

stoves and ovens. It is recommended the unit be installed no closer than 3” from any wall. The

place where the refrigerator is placed must be open and clean. This will reduce the amount of

debris and dirt on the condenser fan and coil.

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page6

www.Fagorcommercial.com

3.3 DATA PLATE

The data plate is located inside the cabinet, near the top front, left corner. Under no

circumstances should the data plate be removed from the unit. The data plate is essential to

identify the particular features of your machine and it is of great benefit to installers,

operators, and maintenance personnel. It is recommended that, in the event the data plate is

removed, you copy down the essential information in this manual for reference before

installation. Removal of data plate will void the warranty.

3.4 LEVELING

Set unit in its final location. A level cabinet looks better and will perform better. Effective

condensate removal and door operation will be effected by leveling. Machine must be leveled

front to back and side to side with a level tool. Castors k it w i ll include shims for leveling.

Insert the shim between the castor and the frame rail. (See installation of castors). Lock front

castors so cabinet does not move. Ensure drain hose is inside drain pan.

3.5 ELECTRICAL CONNECTIONS

Refer to the amperage data in this manual, or on data plate, and your local code or the

National Electrical Code to be sure unit is connected to the proper power source. Verify

correct incoming voltage according to the Data Plate information.

Do not, under any circumstances, cut or remove the ground prong from the power cord.

Fagor units must be properly grounded.

NEVER USE AN EXTENSION CORD! Fagor will not warranty any unit that has been

connected to an extension cord.

Fagor equipment must be grounded and connected in accordance with NEC Article 422

Appliances.

Model

Electrical

Refrigerant Type

SERIAL NUMBER FOR

THE EQUIPMENT

(8 digits and ends in

“M”)

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page7

www.Fagorcommercial.com

DANGER: Power must be turned off and disconnected from the power source when ever

performing maintenance, repair or cleaning the condensing unit.

If machine is still running when power is off, disconnect power at the circuit breaker before

unplugging the machine.

WARNING: Machine and compressor warranties are void if failure is due to improper

electrical installation.

4OPERATION

The temperature displayed by the electronic controller is the temperature of the evaporator

of the unit. The temperature of cabinet will be displayed by the analog thermostat provided.

This display refrigerator is design to keep the product inside cold, under any circumstance

leave food overnight, this will make the evaporator to become frozen and compressor

damage may occur. Damages caused by leaving the unit ON overnight with product will not

be covered under warranty.

4.1 ELECTRONIC CONTROL

After connecting your unit, turn ON rocker switch located next to the controller. The display

will light up showing the temperature inside the unit. Also, the compressor and fan icons will

flash for a period of three minutes. After this delay the unit will start cooling.

Compressor Icon

Evaporator Fan Icon

Temperature inside the cabinet

Verify you don't have any alarms on the temperature controller. If after you turn ON the

equipment the controller shows the alarm icon or an error code, call f or technical service.

They will help you fix the problem.

Note: The controller on the equipment is programmed to display internal temperatures in Fahrenheit (°F). To

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page8

www.Fagorcommercial.com

To increase Set Point of Temperature

To turn t h e u n i t ON/OFF without

unplugging the equipment (press and hold 3

seconds)

To change the set point

To access programming mode

To decrease set Point of Temperature.

To set a manual defrost (press and hold 3

seconds),

change to Celsius (°C), see point 4.2

Description of Buttons on the Controller

Changing the set point of the Temperature on the controller

The unit comes with a factory default set point (-8°F Freezers, 32°F Refrigerators). These set

values will make the unit perform at its maximum capacity. Therefore, it is not recommended

to change the set point. If set point needs to be changed, follow the next steps.

Note:

If you change the set point of temperature, the performance of the equipment will change. Changes made in

the parameters of the controller will not be covered under warranty.

1. -Push the SET button for one (1) second. You should see a flashing number. Release the

button.

2. Press the up and down arrows to increase or decrease the set temperature. Then press

the set button to save the new set point.

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page9

www.Fagorcommercial.com

Note:

The maximum value you can set in the controller is: For refrigerators: 5°C (40°F)

For freezers: -16°C (2°F)

3. If you wish decrease the value of the set point for a new temperature, press the button

DOWN arrow (see the picture below). Press this button to reach the desired value.

Release the button and then press the SET button to keep, and save, the new value.

Note:

The minimum value you can set in the controller is: For refrigerators: -1°C (30°F)

For freezers: -23°C (-8°F)

Changing the reading temperature from °F to °C

To change the reading of the temperature from °F to °C, you need access to the programming

mode in the controller. To do this, press and hold the SET button for five (5) seconds until “PS”

is shown in the display. Release the button and press the SET button one time. Now you will

see the number zero (0). With the button UP arrow, set a value of “22” and then press the SET

button. You will see the “PS” again. Use the button DOWN arrow to find the parameter “EZY”

and press the SET button one time. Using the UP or DOWN button set a value according to the

chart below.

Note:

Freezer equipment can be used like a refrigerator by selecting the value of the parameter “EZY” according to the

chart above. Refrigerators must never be used like a freezer.

After you chose the value for the “EZY” parameter, press and hold the SET button for 5

For Refrigerators

EZY Value

Application

Temperature in °F

Refrigeration

Temperature in °C

Refrigeration

For Freezers

EZY Value

Application

Temperature in °F

Freezer

Temperature in °C

Freezer

Temperature in °F

Refrigeration

Temperature in °C

Refrigeration

TAPAS CASES SERVICE MANUAL / Rev. JUN. 2015

Page10

www.Fagorcommercial.com

seconds.

ou will see the temperature on the display in °F or °C according to

your selection.

4.2 OTHER FUNCTIONS

Manual Defrost

To select manual defrost, hold the button DOWN arrow for 5 seconds. The snow flake icon

will appear on the display. When this icon is solid it indicates that the equipment is in

Defrost mode.

To exit manual defrost, hold the DOWN button arrow for 5 seconds. The snow flake icon will

turn off. Wait 2 minutes for the compressor to start.

Note:

If the equipment doesn’t reach the temperature, first verify that the defrost cycle is not ON.

The unit will go into defrost every six hours for an average of 20 minutes. The defrost cycle is time initiated and

temperature terminated.

NOTE!

Good air flow inside the cabinet is critical. Do not block air flow to the fans. Allow three inches

of space along the front, back, and sides.

CAUTION!

Do not introduce hot foods, chemical or corrosive products, drugs, or

open beverage bottles.

The unit must run for at least 24 hours before any product is placed inside. Failure to do so

may ice up the evaporator coil. Consequently, the unit will never reach the desired set point.

This failure will not be covered under warranty.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Refrigerador de Fagor

Fagor

Fagor 3FFK-5520X Manual de usuario

Fagor

Fagor FUR-27-N Manual sencillo

Fagor

Fagor FFA1504 Manual de usuario

Fagor

Fagor 3FFK-1875 Manual de usuario

Fagor

Fagor FD-281NF Guía de configuración

Fagor

Fagor FQ8925X Manual de usuario

Fagor

Fagor 3FCA-68NFX Manual de usuario

Fagor

Fagor FIC-541 Manual de usuario

Fagor

Fagor FIS-225 Manual de usuario

Fagor

Fagor 3FCA-68NFX Manual

Fagor

Fagor FDS-1143 Manual de usuario

Fagor

Fagor DUO-22 Manual de usuario

Fagor

Fagor FDS-1141DF Manual de usuario

Fagor

Fagor FA3702 Manual de usuario

Fagor

Fagor 1FSC19XEL Manual de usuario

Fagor

Fagor FFJA4845X Manual de usuario

Fagor

Fagor FD-21 Manual de usuario

Fagor

Fagor 3FFK-6645 Manual de usuario

Fagor

Fagor FA16542 Manual de usuario

Fagor

Fagor 3FFK-7845X Manual de usuario

Fagor

Fagor Ingenious Manual de usuario

Fagor

Fagor FD-281NF Manual de usuario

Fagor

Fagor FS-10LA Manual de usuario

Fagor

Fagor FID-23 Manual de usuario

Manuales populares de Refrigerador de otras marcas

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manual de usuario

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manual de usuario

Sharp

Sharp SJ-BA31IEXW2-EU Manual de usuario

CORBERO

CORBERO CC2300MCW Manual de usuario

KitchenAid

KitchenAid 2205264 Manual de usuario

Stengel

Stengel KU 1101 A++ Manual de usuario

NEFF

NEFF KI181 Series Manual de usuario

Hoshizaki

Hoshizaki Reach-In Manual de usuario

Amana

Amana ASD2524VES00 Manual de usuario

BOMANN

BOMANN KGC 213 Manual de usuario

Danby

Danby DAR044A1SLDD Instrucciones de montaje

Samsung

Samsung RF323TE Manual de usuario

Beko

Beko CSA31022 Manual de usuario

IKEA

IKEA FROSTIG C 185 E Manual de usuario

Electrolux

Electrolux ER 6821 D Manual de usuario

True

True TS-28 Manual de usuario

Frigidaire

Frigidaire FSC23R5DW9 Manual de usuario

Beko

Beko LSP4579W Manual de usuario