F5 ARX-4000 Manual de uso y cuidado

ARX 4000 / D103 Parts Replacement

Guide

June 20, 2014

Version 1.4

- 1 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

Removing the Front Bezel

The ARX 4000 employs a highly modular design that allows several key components to be replaced on

a FRU basis. Several of these FRU’s can only be reached by removing the Front Bezel.

Step 1 Remove front bezel

Using the two cutouts on the lower half on either side of the data plane pull gently on the bezel

Fig. 13

- 2 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

Installing the Bezel

Step 1 Installing Bezel

Push Bezel until fully seated

Fig. 14

- 3 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000 Chassis Overview –Front without bezel

ARX-4000+

- 4 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000 /4000+ Control Plane Differences

- 5 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000+ Chassis Overview –Front without bezel

- 6 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000 Chassis Overview –Rear

- 7 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000+ Chassis Overview –Rear

- 8 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

Replacing a X2 module

Preparation

Before beginning ensure that the Field Tech understands that work will be done only on the

Backup Switch.

Verify that the Tech can identify the Backup and the Active and the active switch is fully

functional.

Ensure the correct X2 module needs to be replaced. There are two X2 modules 2/1 and 2/2.

They are labeled as such on the bottom of the slot. 2/1 is the left-most and 2/2 is the right-

most, if facing the front of the switch.

Removing a X2 module

Take the Field Tech through the following steps:

Step 1 Tag the cable so that it will be easily identifiable later

Step 2 Remove the fiber optic cable from the X2 module

Step 3 Grasp both sides of the locking mechanism

Step 4 Pull forward on the locking mechanism

Fig. 1

- 9 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

Installing a X2 module

Step 1 Place the X2 module into the slow heat sink side up

Fig. 2

Step 2 Push forward on the X2 module until fully seated in the slot

Fig. 3

Otros manuales para ARX-4000

1

Tabla de contenidos

Otros manuales de Hardware de red de F5

F5

F5 8900 Instrucciones de montaje

F5

F5 iSeries Manual de usuario

F5

F5 WANJet 500 Instrucciones de montaje

F5

F5 BIG-IP 1600 Instrucciones de montaje

F5

F5 WANJet 300 Manual técnico

F5

F5 ARX-500 Manual de operación y mantenimiento

F5

F5 6900 Manual de usuario

F5

F5 i15000 Series Instrucciones de uso

F5

F5 WANJet 500 Manual técnico

F5

F5 i5000 Series Instrucciones de montaje

F5

F5 6900 Instrucciones de montaje

F5

F5 Herculon SSL Orchestrator Manual

F5

F5 BIG-IP 3900 Manual de usuario

F5

F5 i4000 Series Instrucciones de montaje

F5

F5 ARX-500 Manual

F5

F5 BIG-IP 11050 Manual de usuario

F5

F5 520 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario