Extron electronics TLP Pro 1225TG Manual de usuario

IMPORTANT:

Go to www.extron.com for the

complete user guide and installation

instructions before connecting the

product to the power source.

TLP Pro 1225TG and TLP Pro 1525TG • Setup Guide

Overview

The Extron TLP Pro 1225TG and TLP Pro 1525TG are table-top touchpanels with high resolution capacitive, edge-to-edge glass

touchscreens. The TLP Pro 1225TG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1525TG has a 15.6 inch screen

with a 1366x768 resolution. Both touchpanels are ideal for any AV applications requiring large touchpanels with exible mounting

options and fully customizable interfaces. This guide provides instructions for experienced installers to mount and install these

touchpanels. For more complete details, see the TLP Pro 1225 and TLP Pro 1525 Series User Guide at www.extron.com.

Setup Overview and Checklist

Get Ready

Download and install the latest version of the following software:

zGUI Designer — For designing layouts for Extron TouchLink®Pro touchpanels and third party touch interfaces.

zGlobal Configurator®Plus and Professional — For setting up and conguring the control processor and touchpanel.

zToolbelt — For device discovery, device information, rmware updates, and conguration of network settings, system

utilities, and user management for TouchLink Pro devices.

zGlobal Scripter®— Provides an integrated development environment for Extron control systems programming.

NOTE: All four software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you also require:

IP address Subnet mask Gateway

Username — This can be either admin or user.

Passwords — The factory congured passwords for all accounts on this device have been set to the device serial number.

Passwords can be changed during conguration. Passwords are case sensitive.

NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron (for

either admin or user).

Make a note of the touchpanel MAC address.

Mount and Cable All Devices

ATTENTION:

• Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply section of

the TLPPro 1225 and TLPPro 1525 Series User Guide or the IPL Pro User Guide.

• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «sources

d’alimentation» du TLPPro 1225 and TLPPro 1525 Series User Guide ou du IPLProUserGuide.

Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on page 2).

Connect cables to the touchpanels (see Rear Panel Features on page 4).

An Extron IP Link®control processor must be connected to the same Ethernet subnetwork as the touchpanel.

Set up the Touchpanels for Network Communication

Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork.

Use the Setup Menu (see page 5) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, gateway,

and related settings for the touchpanel.

Conﬁgure the Touchpanels

Create a graphical user interface with GUI Designer (see GUI Designer Help File for step-by-step instructions).

Associate functions with the graphical user interface features by conguring (see the Global Conﬁgurator Help File) or

programming (see the Global Scripter Help File) the system. Global Scripter provides an Extron-exclusive Python library

(ControlScript®) and Global Scripter modules to get you started.

TLP Pro 1225TG and TLP Pro 1525TG • Setup Guide

Mounting

A range of optional mounting kits are available for both models. The

kits must be purchased separately. Follow the installation instructions

provided with the kit.

Removing the back and base covers

Some of these procedures require the back and base covers to be

removed. You must remove the back cover before you can remove the

base cover.

1. Use the provided Extron removal tool. There is one notch on each

side of the back cover (gure 1, 1). Insert the tool into the notch to

release the catch.

2. Use the removal tool to remove the base cover. There are two

notches at the back of the base (2).

2. Drill two pilot holes into the desktop.

3. Remove the base cover (see Removing the back and base

covers, above).

4. Insert two #10 at-head wood screws (not provided) through

the touchpanel and align them with the two pilot holes.

5. Secure the touchpanel to the tabletop.

6. Replace the base cover.

Kensington®Security Lock

For added security, attach a Kensington Security Lock (not

provided) to the metal-reinforced Kensington Security Slot

on the rear edge of the base (see gure 3, 1). The gure

shows the rear edge of the TLP Pro 1525TG base, but

the base of the TLP Pro 1225TG is very similar. Follow the

instructions that are provided by the manufacturer to install

the lock.

Desktop Mounting

The TLP Pro 1225TG and TLP Pro 1525TG come assembled

with stands that allow the units to be placed on any suitable at

surface (for example a desk, table, or lectern).

Fixed Mounting

Figure 2 shows the base of the TLPPro1225TG, with the cover

removed to indicate the position of the mounting holes (see

gure 2, 1). The base of the TLP Pro 1525TG is similar and the

spacing of the mounting holes is identical.

1. Mark the location for two holes, 4.96inches (126 mm) apart.

This measurement is the same for both models.

SMA-1 Swivel Mount Adapter

To swivel either device up to 180° in either direction, use the optional Extron SMA-1 swivel mount adapter, to permanently mount the

touchpanels.

1. Remove the back cover and base cover (see Removing the back and base covers, above).

2. Attach the conduit, insulation disk, and swivel disk and congure the set screws to allow for the degree of swivel that is required

(see the SMA-1 Swivel Mount Adapter Kit User Guide, available at www.extron.com). Place the mounting hole in the base over

the conduit of the SMA-1.

3. Secure the unit with the backing plate and locking nut as described in the SMA-1 Swivel Mount Adapter Kit User Guide.

VESA Mounting

Use a third-party D-type VESA mounting kit with the 100 mm x 100 mm mounting pattern.

1. Remove the back cover.

2. Remove the four screws holding the touchpanel to the base. There are two screws in each base attachment hinge.

3. Follow the instructions provided with the VESA mounting kit.

Figure 1. Remove the Back and Base Covers

Figure 2. Mounting Holes in TLP Pro 1225TG Base

Figure 3. Slot for Kensington Security Lock

Product Category

Front Panel Features

Figure 4 shows the TLP Pro 1225TG front panel diagram. The features of the TLP Pro 1525TG are very similar.

Figure 4. TLP Pro 1225TG Front Panel

AAmbient light sensor — Monitors ambient light level and adjusts screen brightness.

BStatus light — Can be programmed to provide system feedback. The LED light bar is located above the screen.

CCapacitive touch screen — Provides simple control of AV systems:

zThe TLP Pro 1225TG has a 12.1 inch screen with a 1280x800 resolution.

zThe TLP Pro 1525TG has a 15.6 inch screen with 1366x768 resolution.

DSpeakers — Provide stereo audio for video preview and audible feedback from button presses. They are located below the

screen, one on each side of the panel.

EMotion sensor — Detects motion between three to ve feet from the touchpanel, and at least 15° from the center axis.

zIf the Sleep Timer has been set (see Setup Menu on page 6), and no motion has been detected for a user-dened

period of time, the touchpanel enters sleep mode.

zIf Wake on Motion has been set (see Setup Menu), and motion is detected by the sensor while the screen is in sleep

mode, the screen display is restored and active.

TLP Pro 1225TG and TLP Pro 1525TG • Setup Guide

Rear Panel Features

Figure 5 shows the TLP Pro 1225TG rear panel diagram (with the base and back cover removed). The features of the

TLP Pro 1525TG are very similar.

XTP /

PoE /

LANHDMI IN

12VDC 3A

RESET

Marking

ARear status light EHDMI input IMenu button (see page 5)

BVesa mounting holes FXTP/LAN/PoE input JReset button (see page 5)

CPower supply input GAudio output (see page 5)

DUSB connectors HReset LED (see page 5)

Figure 5. TLP Pro 1225TG Rear Panel (with base and back cover removed)

ARear status light — An LED light bar that can be programmed to provide system feedback.

BVESA mounting holes (4) — For use with D-type VESA mounting kits with the 100 x 100 mm mounting pattern.

CPower supply input — Connect a 12 VDC, 3.0 A Limited Power Source (LPS) power supply to this DC plug connector.

ATTENTION:

• The touchpanels can use a 12 VDC desktop power supply or Power over Ethernet. Do not connect either power

supply before reading the Attention in the Power section of the TLPPro 1225 and TLPPro 1525 Series User Guide.

• Les écrans tactiles peuvent utiliser une source d’alimentation externe 12 Vcc ou l’alimentation POE via Ethernet.

Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section

«PowerSupply» du TLPPro 1225 and TLPPro 1525 Series User Guide.

DUSB connectors (2) — For peripheral controls.

EHDMI input — For alternative video input.

FXTP/LAN/PoE input

zXTP input — Connect the touchpanel to the XTP source using a twisted pair cable, terminated with an RJ-45 connector.

For complete information about which cables to use, see the user guide for your XTP product.

zLAN input — Connect the touchpanel to the LAN using a twisted pair cable, terminated with an RJ-45 connector.

zPoE input — The connector can be used with a PoE power injector (see Connecting Power on page 5).

NOTE: Some XTP models are able to remotely power these touchpanels but not all have that capability. Go to the Extron

website and check the product page for your XTP model to ensure it can power your touchpanel.

An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.

gure 5

note

Product Category

GAudio output (see ﬁgure 5 on page 4) — For use with headphones or assistive listening devices.

HReset LED — Provides feedback about the reset status when the user presses the reset button.

IMenu button — Activates the setup menu (see Setup Menu on page 6).

JReset button — Pressing the reset button allows the unit to be reset in any of four different modes (see Reset Modes on

page 5). For more information, see the TLPPro 1225 and TLP Pro 1525 Series User Guide).

Connecting Power

ATTENTION:

• Do not power on the touchpanels until you have read the Attention notication in the “Rear Panel Features” section of

the TLP Pro 1225 and TLP Pro 1525 Series User Guide.

• Ne branchez pas les écrans tactiles avant d’avoir lu la mise en garde dans la section « Rear Panel Features » du

TLP Pro 1225 and TLP Pro 1525 Series User Guide.

The power injector must be purchased separately. Figure 6 shows the Extron PI 140. Your power injector may look different.

1. Connect a straight-through Ethernet cable from the power injector to a switch or router. This cable carries network information

from the switch or router to the power supply input.

Audio output

Reset LED

Menu button

Reset button

2. Connect a second straight-through cable from the power injector to the

XTP/PoE/LAN connector of the touchpanel (see ﬁgure 5, F, on page 4).

This cable carries the network information and 48VDC from the power injector

to the touchpanel.

3. Connect the IEC power cord to a convenient 100 VAC to 240 VAC, 50-60 Hz

power source.

Alternatively, use an Ethernet cable to connect the XTP/LAN/PoE+ port of the

interface to a PoE+ switch or connect the touchpanel directly to an XTP model that

is capable of remotely powering a touchpanel (see the note on page 4).

100-240V~50/60 Hz

1.1A MAX INPUT OUTPUT

POWERED TLP

LAN

To Network or

XTP Device

To a TLP Pro

touchpanel

Extr

on PI 140

Figure 6. Connecting the Power Injector

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

For information about replacing and disposing of batteries, see the TLP Pro 1225 and TLP Pro 1525 Series User Guide at

www.extron.com.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876 68-3474-51 Rev. A

07 20

TLP Pro 1225TG and TLP Pro 1525TG • Setup Guide

Setup Menu

Press the Menu button (ﬁgure 5, I, on page 4) to open the

setup menu. Select any of the six available screens (Status,

Network, Display, Audio, Input and Advanced) by pressing

the appropriate button in the navigation bar at the top of the

screen (for more information, see the TLPPro 1225 and TLP Pro

1525 Series User Guide).

Figure 7 shows the setup menu for the TLP Pro 1225TG. The

setup menu for the TLP Pro 1525TG is very similar.

Info

Model: TLP Pro 1225TG

Part Number:60-1788-02

Firmware

Version: 1.02.0000.b003

PoE: Active

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:

Project:

Sleep Timer:

1280x800

5 Minutes

Audio

Master Volume:

Master Mute: Off

100

Input

HDMI:No Signal

Status DisplayAudio Advanced Exit

NetworkInput

Advanced

Controller IP: 192.168.254.250

Project Size: 1/197 MB

Bootloader

Version: 1.03.0000

XTP: 1280x720 HDCP

Figure 7. Setup Menu: Status Page for TLP Pro 1225TG

Reset Modes: A Brief Summary

The TLP Pro 1225TG and TLP Pro 1525TG offer the following reset modes. For full information about the modes, see the TLPPro

1225 and TLP Pro 1525 Series User Guide.

• Use factory firmware: Use this mode to replace rmware in the event of rmware failure. Press and hold the Reset

button (ﬁgure 5, Jon page 4) while applying power to the unit.

• Reset All IP Settings: Use this mode to reset all network settings without affecting user-loaded les. Press and

hold the Reset button for 6 seconds. After the Reset LED (H) blinks twice, release and

momentarily press the Reset button.

• Reset to Factory Defaults: Use this mode to return the touchpanel to factory default settings, including passwords. Press

and hold the Reset button for 9 seconds. After the Reset LED blinks three times, release and

momentarily press the Reset button.

NOTES:

• The factory congured passwords for all accounts on this device have been set

to the device serial number. Passwords can be changed during conguration.

Passwords are case sensitive.

• If the device is reset to default settings, the passwords are reset to the default

password, which is extron (for either admin or user).

• Enable or Disable the

DHCP Client

Use this mode to toggle between DHCP enabled and DHCP disabled. Press the Reset button

ve times, consecutively. After the fth press, do not press the button again within 3 seconds.

If DHCP was enabled, it is now disabled and the Reset LED blinks three times. If DHCP was

disabled, it is now enabled and the Reset LED blinks six times.

Otros manuales para TLP Pro 1225TG

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel táctil de Extron electronics

Extron electronics

Extron electronics TouchLink TLP 710CV Manual de usuario

Extron electronics

Extron electronics TLP 700MV Manual de usuario

Extron electronics

Extron electronics TLP Pro 1020T Manual de usuario

Extron electronics

Extron electronics TouchLink Series Instrucciones de uso

Extron electronics

Extron electronics TLP Pro 1225MG Manual de usuario

Extron electronics

Extron electronics TLP 700TV Manual de usuario

Extron electronics

Extron electronics TLP 350MV Manual de usuario

Extron electronics

Extron electronics TouchLink TLP Pro 1220 Series Manual de usuario

Extron electronics

Extron electronics TLP 1000MV Manual de usuario

Extron electronics

Extron electronics TLP Pro 1725TG Manual de usuario

Extron electronics

Extron electronics Scan Rate Indicator SRI 200 Manual de usuario

Extron electronics

Extron electronics TLP 700MV Manual de usuario

Extron electronics

Extron electronics RWM 1 Manual de usuario

Extron electronics

Extron electronics TLP Pro 1220TG Manual de usuario

Extron electronics

Extron electronics TLP Pro 720M Manual de usuario

Extron electronics

Extron electronics TLP Pro 525M seriesl Manual de usuario

Extron electronics

Extron electronics BB 1000M Manual de usuario

Extron electronics

Extron electronics TLP Pro 1220MG Manual de usuario

Extron electronics

Extron electronics TLP Pro 1225MG Manual de usuario

Extron electronics

Extron electronics TLP Pro 720C Manual de usuario

Extron electronics

Extron electronics TLP 700MV Manual de usuario

Extron electronics

Extron electronics TouchLink TLP Pro 1025T Series Manual de usuario

Extron electronics

Extron electronics ZRTP Series Manual de usuario

Extron electronics

Extron electronics TLP Pro 720M Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario