Extron electronics TLP 700TV Manual de usuario

TLP 700TV • Setup Guide

Overview

The Extron TLP 700TV is a free-standing TouchLink®Panel (TLP) that provides simple and versatile conguration and control

for a range of control systems. The panel can be wall-mounted using the optional Extron mounting kit. See the Extron website

(www.extron.com) for a list of compatible models.

Graphic and text objects are displayed on the screen. Functions associated with those objects are initiated by touching the screen.

The TLP 700TV communicates with the units that it controls through an Ethernet connection to an IP Link unit. An MTP twisted pair

cable allows the screen to be used to preview composite video or S-video.

NOTE: The RJ-45 output on the rear panel of the TLP 700TV must be connected to a network switch, hub, or router that is

connected to an Ethernet LAN or the Internet. An Extron IP Link controller must also be connected to the same network domain.

See the Extron website (www.extron.com) for a list of compatible models.

This guide provides instructions for experienced installers to mount and perform initial conguration on the TLP700TV. For more

detailed information, see the TLP 700MV and TLP 700TV User Guide, which is available at www.extron.com.

TLP 700TV Front Panel Features

Figure 1. TLP 700TV Front Panel.

1Buttons — These ten backlit push-buttons (ve on either side of the screen) can be congured, using the Extron Global

Congurator software, to control commonly used functions.

2Motion sensor — This sensor is capped with a small Fresnel lens that focuses light onto the sensor. When no motion has been

detected for a user-dened period of time, the unit goes into sleep mode. When motion is detected in the vicinity of the panel, the

screen display is restored and all buttons are active.

3Encoder knob — This knob is used for volume control.

4Light sensor — This sensor monitors the level of ambient light and adjusts the screen brightness and button backlighting.

5LCD screen — This 800x480 resolution LCD screen has a touch overlay. The Extron GUI Congurator software is used to

design a graphic user interface, which displays buttons, text, or icons on the screen. The Extron Global Congurator software is

used to program these screen objects to perform user-dened functions.

6Speaker — A single 2 W speaker provides audible feedback for the user.

7Reset button — This button is recessed behind the bezel and is used to select from the four different reset modes that are

available with TouchLink panels (see Reset Modes on page 3).

8Menu button — This button is recessed behind the bezel. It activates the on-screen menus for setting up the panel and

calibrating the unit.

9Reset LED — This LED is recessed behind the bezel. It is visible only when the faceplate has been removed. It lights as an

indicator for the Reset modes.

Product Category

IMPORTANT:

Go to for the

complete user guide and installation

instructions before connecting the

product to the power source.

www.extron.com

Base Features

Three adjustable potentiometers in the base are used to control

sharpness, and gain for both S-video luminance (Y), and S-video

chrominance (C). If a composite video signal is being used, the

gain is controlled by the center potentiometer (Vid/Y).

To adjust these settings:

1. Apply power to the unit.

2. Provide a video input through the MTP RJ-45 connection.

3. Enter the Setup Menu (see the next page).

4. Navigate to the Video screen and calibrate the video settings.

Gain

Vid/Y

Gain

Sharp

33-1814-01A

Gain

Vid/Y

Gain

Sharp

33-1814-01 A

Figure 2. TLP 700TV Base Features

Gain

Vid / Y

Gain

Sharp

33-1814-01A

Use two 8-32 scre

through these holes

to secure the base

to the desk top.

Adjustab

otentiometers

Figure 3. Securing the TLP 700TV to a Desktop

2223

Figure 4. TLP 700TV Rear Connections

Figure 5. Securing the Power Cable

provided to the 2-pole captive screw connector (see

gure 4, 3).

2. Form a loop from the power supply cable that ts into the

gap between the tail to the captive screw connector and the

raised hook in the base of the unit (see gure 5).

3. Secure the power cable loop to the base of the unit with a

zip tie (see gure5, 1).

4. Insert the network cable into the RJ-45 socket (see

gure 4, 2) closest to the green and yellow LEDs (1).

5. If required, insert the twisted pair connection for the Extron

MTPTransmitter into the MTP RJ-45 socket (4).

ATTENTION:

• The right RJ-45 connector (gure 4, 4) must be

connected to an Extron MTP Transmitter.

• Le connecteur RJ-45 droit (gure 4, 4) doit être

connecté à un émetteur MTP Extron.

NOTES:

• The minimum distance from the MTP transmitter

to the TLP is 50feet.

• Extron recommends securing all cables with a zip

tie (see gure 6).

Installing the TLP 700TV

The TLP 700TV comes assembled with a stand that allows

it to be placed on any suitable at surface. If required,

secure the unit to the top of the desk by drilling two holes

through the desk 5.1 inches (13cm) apart. Insert two 8-32

screws through the bottom of the desk into the two holes in

the base.

NOTE: If you are using the MTP video input, this must

be calibrated before you secure the unit to the at

surface (see Base Features, above).

ATTENTION:

• Do not connect any external power supplies until

you have read the Attention notications in the

Power Supply section of the TLP 700MV and

TLP 700TV User Guide.

• Ne branchez pas de sources d’alimentation

externes avant d’avoir lu les mises en garde dans la

section «PowerSupply» du TLP 700MV and TLP

700TV User Guide.

NOTE: Extron strongly recommends securing the power

supply cables to the base of the unit with a zip tie.

1. For correct operation, connect the power supply

Figure 6. Securing all Cables

TLP 700TV • Setup Guide (Continued)

VESA Mounting (optional)

The stand for the TLP 700TV can be removed and replaced with the Extron

VM700Tkit (part #70-692-01). This bracket (see gure 7) ts into any

third-party VESATypeD75mm wall mount system. For more information,

see the instructions that come with the VM700Tkit.

75mm

2.95”

75mm

2.95”

Figure 7. VMT Vesa Mount Bracket

Setup Screen

1. Use a paper clip to press the recessed menu button (see gure 1, 8). This opens

the setup menu at the Main setup page (see gure 8).

2. Touch an area of the screen to bring it into focus and use the up and down buttons

or the volume control knob to adjust the value. Some options have a single button

and toggle between Off and On when pressed.

Use the different screen menus to adjust the following options. For more details, see

the TLP 700MV and TLP 700TV User Guide, which is available at www.extron.com.

• Main (see gure 8) — This screen is used to adjust the Sleep timer, Backlight,

Auto Backlight, LED Backlight, and Wake on Motion functions.

• Volume — This screen is used to adjust the Master, Click, Sounds, and Line In

volume settings.

• Time — This screen is used to set up the correct time and date.

• Network — This screen is used to set the IP Address, the Subnet Mask, and to

enable or disable Dynamic Host Conguration Protocol (DHCP).

• Video — This screen provides a small video preview window and the controls to

set up the video Contrast, Color, Brightness, and Tint.

Calibration Screen

While in the Setup menu, press the Menu button a second time to open the calibration

screen (see gure 9). When all four points have been calibrated, the screen reopens to

the Setup screen.

Press Exit to close the on-screen menus.

Figure 8. Setup Menu

Reset Modes

The four reset modes can be initiated by using a paperclip to press the Reset button (see gure 1, 9, on page 1).

NOTE: See the TLP 700MV and TLP 700TV User Guide at www.extron.com for additional details.

• Factory Firmware Mode — Hold the Reset button while applying power to reset the unit back to the base rmware shipped with

the unit.

• Run/Stop Events Mode — Hold the Reset button until the reset LED blinks once (3 seconds), then release and press Reset

momentarily (less than 1 second) within 1 second.

This mode turns events on or off.

• Reset All IP Settings Mode — Hold the Reset button until the reset LED blinks twice (6 seconds), then release and press

Reset momentarily (less than 1 second) within 1 second.

This mode resets the IP address, subnet, gateway, port mapping, and DHCP settings back to factory defaults. The reset LED

blinks 4 times in quick succession, conrming the reset and turning events off. If necessary, reset the IP address, using ARP and

the MAC address.

• Reset Factory Defaults Mode — Hold the Reset button until the reset LED blinks 3 times (9 seconds), then release and press

Reset momentarily (less than 1 second) within 1 second.

This mode causes a reset to factory defaults for everything except rmware.

NOTES:

• The factory congured passwords for all accounts on this device have been set to the device serial number. Passwords

are case sensitive.

• If the device is reset to default settings, the password will be the default password conguration. The default password

is extron.

Figure 9. Calibration Screen

Conﬁguring the TLP 700TV (Initial Setup)

Before using the TLP 700TV, congure it, using the on screen menus. Five

different screens (Main, Volume, Time, Network, and Video) can be selected

by pressing the appropriate button at the left side of the screen. Press the

Exit button in the bottom left corner to close the menus.

Product Category

TLP 700TV • Setup Guide (Continued)

Software

NOTES:

• To congure the TLP 700TV, use GUI Congurator and Global Congurator 3. This touchpanel is not compatible with GUI

Designer or Global Congurator Plus and Professional.

• These software programs can be downloaded from the Extron website (www.extron.com). For information about

downloading software see the TLP 700MV and TLP 700TV User Guide.

• See the GUI Conﬁgurator Help File or the Global Conﬁgurator 3 Help File for information about using these programs.

Figure 10. GUI Conﬁgurator

Figure 11. Global Conﬁgurator 3

Conﬁguring the TLP 700TV Interface

with Global Conﬁgurator 3

Install the Global Congurator3 software on a PC and

use it to assign functions to the screen elements that

were created with GUI Congurator.

Open the program by clicking on the desktop icon or

by using Windows Explorer to navigate to the correct

le on your computer. When the program opens (see

the opening screen in gure 11), follow the on-screen

instructions to congure the IP address of the units.

Open the project created with GUI Congurator3 and

assign functions to the buttons and screen graphics and

text.

When the functions have been assigned to all screen

objects, build the project and upload it to the IP Link

controller. For complete information, consult the user

guide for the controller.

Designing the TLP 700TV Interface with

GUI Conﬁgurator

Install the GUI Congurator software on a PC and use it

to design the interface that will appear on the TLP700TV

screen.

Open the program by clicking on the desktop icon or by

using Windows® Explorer to navigate to the correct le on

your computer. When the program opens (see the opening

screen in gure 10), you have an option of opening an

existing project, opening an existing template, or starting a

new project to design a completely new interface.

468-1378-51 Rev. C

01 20

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

For information about replacing and disposing of batteries, see the TLP 700MV and TLP 700TV User Guide at www.extron.com.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Otros manuales para TLP 700TV

Otros manuales de Panel táctil de Extron electronics

Extron electronics

Extron electronics ZRTP Series Manual de usuario

Extron electronics

Extron electronics TouchLink Series Instrucciones de uso

Extron electronics

Extron electronics BB 1000M Manual de usuario

Extron electronics

Extron electronics Scan Rate Indicator SRI 200 Manual de usuario

Extron electronics

Extron electronics TLP Pro 1225MG Manual de usuario

Extron electronics

Extron electronics TLP 700MV Manual de usuario

Extron electronics

Extron electronics TLP Pro 1220MG Manual de usuario

Extron electronics

Extron electronics TLP 1000MV Manual de usuario

Extron electronics

Extron electronics TouchLink TLP 710TV Manual de usuario

Extron electronics

Extron electronics TLP Pro 720M Manual de usuario

Extron electronics

Extron electronics TLP Pro 725T Manual de usuario

Extron electronics

Extron electronics TLP Pro 300M Series Manual de usuario

Extron electronics

Extron electronics TLP Pro 1725TG Manual de usuario

Extron electronics

Extron electronics TLP Pro 1225MG Manual de usuario

Extron electronics

Extron electronics TLP Pro 525T Series Manual de usuario

Extron electronics

Extron electronics TLP Pro 720M Manual de usuario

Extron electronics

Extron electronics TLP Pro 720C Manual de usuario

Extron electronics

Extron electronics TLP Pro 720C Manual de usuario

Extron electronics

Extron electronics TLP 700TV Manual de usuario

Extron electronics

Extron electronics TLP Pro 720M Manual de usuario

Extron electronics

Extron electronics TLP 1000MV Manual de usuario

Extron electronics

Extron electronics TLP Pro 1220MG Manual de usuario

Extron electronics

Extron electronics TLP 700MV Manual de usuario

Extron electronics

Extron electronics TLP 1000MV Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario