Extron electronics ACP 106 EU Manual de usuario

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

ACP 106 EU/MK • Setup Guide

The Extron ACP 106 EU/MK Audio Control Panels are fully congurable control interfaces for use with any Extron ACP-enabled

device.

Each ACP 106 EU/MK includes two ACP ports, which support power and communication between the host device and the

ACP 106 EU/MK. Up to eight ACP panels can be used per host device for more demanding control needs.

NOTE: The ACP 106 EU front and rear panels are identical to those of the ACP 106 MK. The only difference is the shape of

the plastic faceplate attached to the front of the device. The panels function identically.

Front Panel Features

VOLUME

MUTE

PROGRAM

MIC

Extron

Figure 1. ACP 106 EU Front Panel

Planning the System and Installation

When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see

the ACP 106 EU and ACP 106 MK product pages at www.extron.com for more information about the ACP 106 EU/MK).

Installation

Step 1: Get Ready

Use the following checklist to prepare for the installation:

Download and install the latest version of software, rmware, and device drivers needed to congure the host device and

congure the connected ACP products (see the host device user guide, available on www.extron.com, for details on

software and drivers).

Obtain cables, mounting hardware, and any other supplies required for ACP 106 EU and MK installation.

Figure 2. ACP 106 EU Rear Panel

ACP

PWR LOAD

= 1.5W

+S -S G +V+S -S G

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

Rear Panel Features

AACP Ports (2)

BConnection Status LED

CReset Button

DBus ID DIP Switches

AMute Buttons

BTransmit LED

CVolume Buttons

DVolume LED Meter

EFunction Button 1

FFunction Button 2

ACP 106 EU/MK • Setup Guide (Continued)

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP 106 EU/MK into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le ACP 106 EU/MK dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• If the ACP 106 EU/MK will be installed into ne furniture, it is best to hire a licensed, bonded craftsperson to cut the

access hole and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le ACP 106 EU/MK dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et

qualié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 106 EU/MK

must be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with

the ACP106 D.

Americans with Disabilities ACT (ADA) Compliance

When planning where to install these devices, consider factors affecting accessibility of the button panel such as height

from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections

307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 ADA Standards for Accessible Design available at

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external wall boxes (EWBs), and surface or

tabletop mounting boxes for use with the ACP button panels. The ACP 106 EU and ACP 106 MK are 1-gang EU and MK size

devices.

Step 3: Removing the Plastic Faceplate, Button Panel, and Changing

the Buttons

The plastic faceplate and buttons can be replaced. Additional buttons ship with the device and

others can be ordered from www.extron.com.

To change the buttons:

1. Insert the Extron removal tool (pry tool) between one side of the plastic faceplate and the

button plate. Release the catch holding the wallplate to the metal mounting plate (see 1

in the gure to the right). If necessary, use the pry tool to release the second catch on the

opposite side.

2. To separate the button plate from the control plate, insert a small at-bladed screw driver

into one of the slots (see 2in the gure at the bottom of the page).

3. Press the blade of the screw driver in until there is an audible

click and the tab is pushed out of the slot.

4. Repeat steps 2 and 3 to release all four tabs holding the button

plate in place.

5. Tilt the top of the button plate forward as it is removed to

prevent the buttons from falling out (3).

VOLUME

MUTE

MIC

PROGRAM

VOLUME

MUTE

MIC

PROGRAM

Extron

Insert

to lin

6. To remove a button, press a button backward through its slot in the button plate until the

membrane containing the button is free.

7. To replace a button, align the two pegs in the button membrane with the holes located at

opposite corners of the empty slot on the back of the button faceplate and push the button

forward so it ts in the desired slot (see the gure to the right). Ensure the button text

orientation is correct.

8. Press the button into the button plate until the pegs on the membrane are seated in the

corresponding holes.

9. Repeat steps 6 through 8 for any other buttons being replaced.

10. Align the back of the button plate with the control plate and press it into place. The four

tabs released in steps 2 through 4 snap back into place.

11. Ensure the plastic faceplate and metal mounting plate are in the correct orientation. To reattach the plastic faceplate, press

the faceplate back into the metal mounting plate, using the two catches released in step 1.

Step 4: Set Bus ID Addresses

ACP

+S -S G+V +V+S -S G

PWR LOAD

= 1.5W

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

V+

S G

–

010010

123456

000001

123456

18Unit address

DIP switches

Binary address

ACP port on a

DMP Plus, or on

another ACP

endpoint

ACP Ports

• Connect up to eight (8) ACP endpoint devices per

DMP Plus.

• Wire the connectors the same at both ends.

• These ports are identical. You can connect devices

interchangeably to either port.

• Do not exceed a total of 1000 feet (305meters) of cable for

connections between the DMP Plus and all of the ACP

panels.

• Power is provided by the DMP Plus, a PS 1220EB power

inserter, or an Extron 12 VDC power supply.

Bus ID Address DIP Switches

• Use these DIP switches to set the six-bit, binary

bus address for the ACP 106 EU/MK.

• Each ACP connected to the same DMP Plus

must have a unique address.

• Switch 1 (on the left) is the highest value (32, the

the most signicant bit [labeled “MSB”]).

• Switch 6 (on the right) is the lowest (1, the least

signicant bit [labeled “LSB”]).

• Up = on = 1, Down = off = 0

Examples:

Figure 3. ACP 106 EU/MK Rear Panel and Bus ID DIP Switch Assembly

Set the bus identication (bus ID) DIP switches for the ACP 106 EU/MK and

any other ACP panels being connected to the system. Each ACP device

must have a unique bus ID. If multiple panels have the same bus ID, address

conicts may cause one or more of the panels to not be recognized in DSP

Congurator or by the host device. Up to eight ACP devices can be connected

in the same system.

Each ACP device in a system must have a unique six-digit binary bus ID. ACP

bus IDs are set using the DIP switch assembly on the rear panel of the ACP

106 EU/MK (see gure 3).

Switch 1 on the left sets the most signicant bit (highest number, 32) while

switch 6 on the right sets the least signicant bit (the lowest number, 1). See

the example addresses to the right.

Slide

1 2 3456

BUS ID

Example Addresses

Bus ID

(Decimal)

Binary

Address

DIP Switch

Setting

0 000000*

1 2 3456

1 000001

1 2 3456

2 000010

1 2 3456

3 000011

1 2 3456

4 000100

1 2 3456

5 000101

1 2 3456

6 000110

1 2 3456

7 000111

1 2 3456

8 001000

1 2 3456

*Address 000000 is reserved for the control processor and cannot be used by any ACP devices.

ACP 106 EU/MK • Setup Guide (Continued)

Step 5: Cable All Devices

1. Connect the ACP panel to the host device.

2. Connect ACP panels to each other if multiple panels are being used in the control system (see the wiring diagram below for

correct wiring).

NOTES:

• Wire both ends of each ACP cable the same. Connectors are interchangeable between the host device and ACP

device.

• Do NOT power an ACP panel from more than one power source.

3. Apply power to the host device after correctly cabling all devices.

Cabling

Attach cables using the diagram below as a guide. Wiring is the same for all ACP models. Connect a 4-pole captive screw

connector to each end of the cable, wiring both ends the same. In most cases, the ACP devices are powered by the host

DMPPlus Series device. Power is carried on the V+ pin of the ACP 106 EU/MK and other ACP devices.

Extron STP20-2/1000 or STP20-2P/100 cable is recommended for ACP device connections.

Ground

+Signal

Signal

+12 VDC

Black

and

Drains

Green

White

Red

S+S

Drain Wires

Basic ACP Connector Wiring

ACP devices that are relatively far from the host device can be connected to an optional Extron PS 1220EB eBUS power inserter

or an Extron 12 VDC desktop power supply as shown in the diagrams below and on the next page (see the

ACP 106 EU/MK Speciﬁcations at www.extron.com for cable length to determine if additional power is recommended).

ATTENTION:

• Always use a power supply supplied or specified by Extron. Use of an unauthorized power supply voids all regulatory

compliance certification and may cause damage to the supply and the unit.

• Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une source d’alimentation non autorisée

annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que l’unité.

• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked

“Class2” or “LPS” and rated output 12VDC, minimum 1.0A.

• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit être alimenté par une source

d’alimentation certifiée UL de classe 2 ou LPS et paramétré à 12VDC et 1,0A minimum.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération

ou dans les cavités murales.

• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA70,

article725 and the Canadian Electrical Code part1, section16. The power supply shall not be permanently fixed to

building structure or similar structure.

• Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/

NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas être

fixée de façon permanente à une structure de bâtiment ou à une structure similaire.

eBUS 24 WATTS MAX

100-240V 50-60Hz

0.6A MAX

V+

S G

–

V+

S G

–

S+

V+

S G

–

S+

V+

S G

–

V+

S G

–

S+

V+

S G

–

ACP port on

an ACP or

other ACP

endpoint

device

V+

S G

–

LAN

DMP 128 Plus C

RxTx G

RS-232

+S+V -S G

5 6 7 8

1 2 34

OUTPUTS

DMP EXP

ACP

REMOTE

USB AUDIO RESET

DMP 128 Plus

S+S

Tie drain wires

to ground.

S+S

Ground

+Signal

Signal

+12 VDC

S+S

ACP Connections

• Connect up to eight (8) ACP

endpoint devices to the PS 1220EB.

• Wire the connectors the same at

both ends.

• All ports are identical and

interchangeable.

Power Input

(100-240 VAC,

50-60 Hz)

PS 1220EB

ATTENTION: Do NOT connect the power

pin to any device that is already powered

by the DMP Plus or by an additional

power supply.

3/16" (5 mm) Max.

Figure 4. Cabling ACP Devices with a PS 1220EB Power Inserter

ACP 106 EU

Rear Panel

Tie drain wires to ground.

RidgedSmooth

3/16" (5 mm) Max.

ACP port

on a DMP

Plus

ACP port

on another

ACP endpoint

NOTE:

Check the polarity of the power

supply before connecting it to the ACP.

V+

S G

–

V+

S G

–

Ground

+Signal

Signal

Ground

+Signal

Signal

+12 VDC

– Return

+12 VDC input

External Power Supply

(12 VDC, 2.0 A)

Ground

all Devices

P 106 E

ear

ane

ACP

+S -S G +V+S -S G

PWR LOAD

= 1.5W

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

Power Input, External Power Supply (optional)

• Connect to an Extron 12 VDC, 2.0 A, power supply.

Figure 5. Cabling ACP Panels with an Extron 12 VDC Power Supply

ACP 106 EU/MK • Setup Guide (Continued)

Step 6: Conﬁgure the System

NOTE: For complete information on creating configuration files and operating DSP Configurator, see the host device user

guide and the DSP Configurator Help file.

1. Create a new host device conguration le in DSP Congurator and create all groups, presets, and macros to be controlled

by the ACP device.

2. Select Tools>Configure ACPs in DSP Congurator and congure the ACP button actions and panel IDs.

3. Connect to the host device in Live mode with a TCP/IP connection and push the conguration le to the device.

Step 7: Test and Troubleshoot

1. Verify the ACP bus ID DIP switches are set to the desired address on each unit and that there are no bus ID address conicts

in the system.

The ACP 106 EU/MK has a rear panel LED that can be used as a diagnostic tool. Your model may have a single monochrome

LED (green) or a single bicolor LED that can light green, amber, or red (amber + green). The device status indicated by the

LED is shown in this table:

Device Status Single LED (green) Single LED (bicolor)

No power, eBUS cable broken. Off Off

Device is receiving power and communicating correctly

with the DMP Plus.

Lights solidly Lights green

Device is receiving power but cannot communicate with

the DMP Plus.

Slow blink Lights amber

Device is receiving power and communicating with the

DMP Plus but there is an address conflict.

Fast blink Lights red

2. Verify cables to and from the ACP devices are wired the same at each end.

3. Test the system:

a. Press the ACP device buttons and ensure the buttons light as expected and that the appropriate control actions are

triggered. Commands can be veried using DSP Congurator. DataViewer can also be used for command verication if

responses are congured.

b. Ensure the audio levels respond correctly to the volume and mute buttons.

4. Make adjustments to wiring, bus ID addresses, and system conguration as needed. Remember that the rear panel ports and

DIP switches are not accessible after the ACP is mounted. If needed, push a revised conguration to the ACP device through

the host device using DSP Congurator.

If you have questions during installation and setup, call the Extron S3 Sales and Technical Support Hotline or the Extron S3

Control Systems Support Hotline (1.800.633.9877).

VOLUME

MUTE

MIC

PROGRAM

MK Wall Box

Wall

Metal Mounting

Bracket

Plastic

Faceplate

ACP 106 MK

VOLUME

MUTE

MIC

PROGRAM

Wall Box

Plastic

Faceplate

Metal Mounting

Bracket

ACP 106 EU

Step 8: Mounting the ACP 106 EU/MK

Prior to mounting:

1. Feed all device cables through the wall or furniture.

NOTE: If the unit is not installed in a mud ring, the plastic spacer must be installed. The spacer positions the unit to allow

the plastic faceplate to attach properly and securely.

2. Ensure the cables are connected to the ACP 106 EU/MK rear panel.

Mounting ACP 106 EU or ACP 106 MK Units to an Electrical Wall Box

The ACP 106 EU can be mounted in any standard 1-gang EU electrical junction box. The ACP 106 MK can be mounted in any

standard 1-gang MK electrical junction box.

NOTES:

• The electrical wall box is not provided and must be purchased separately.

• Install the electrical wall box by following the instructions provided by the manufacturer.

• Use the metal mounting bracket provided with ACP unit.

To mount an ACP 106 EU/MK:

1. Decide where the panel will be located. Take into consideration

the position of wall studs and windows that could obstruct cable

runs.

2. Install the electrical wall box (see 1in the gure to the right) by

following the instructions provided by the manufacturer. Attach

the provided metal mounting bracket (2) using the two provided

screws.

NOTES:

• The metal mounting brackets provided with the

EU and MK models are different and are not

interchangeable.

• Ensure the bracket is in the correct orientation (with

the side marked “Front” facing away from the wall.

• The EU model is attached with screws at the top and

bottom.

• The MK model is attached with screws on both the

sides.

3. Disconnect power from all devices at the source and run cables

through the hole in the wall. Pass them through the metal mounting

bracket and plastic faceplate and connect them to the rear panel

captive screw connectors (see Step 5: Cable All Devices on

page4).

4. Set the DIP switches to give the panel a unique ID number (see

Step 4: Set Bus ID Addresses on page3).

5. Insert the ACP 106 EU/MK into the plastic faceplate (3) and press

the entire assembly into the metal mounting bracket (2). The device

is secured to the metal mounting bracket by two catches (one on each

side) and holds the wallplate in place.

68-3067-50 Rev. B

07 19

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Mounting ACP 106 EU Units in a Raceway

NOTES:

• If there is a gap between the metal mounting bracket and the wall frame, insert the provided spacer between the

mounting bracket and the rim of the junction box (see gure below).

The spacer looks very similar to the metal mounting bracket, but has a slightly larger center opening, has holes instead

of slots for the mounting screws, and is engraved with the words “Optional Spacer” and “Place behind bracket”.

• Do not use the spacer instead of the metal mounting bracket. The spacer has a larger opening and will not hold the ACP

106 EU/MK securely in the wall frame.

To mount the ACP 106 EU/MK to a raceway using the spacer:

1. Mount an electrical box in the raceway (see 1in the

gure to the right). Follow the instructions provided by the

electrical box manufacturer.

2. If required, align the screw holes of the provided spacer

with the holes in the electrical box (2).

3. Align the screw holes in the metal mounting bracket with

the holes in the spacer and electrical box (3).

NOTE: Ensure that the front surface of the mounting

bracket is facing out (away from the wall).

4. Use the two provided screws to secure the metal mounting

bracket and spacer to the junction box (4). Leave the

screw heads protruding approximately 1/8 inch (3.18 mm)

from the surface of the spacer.

5. Rotate the metal mounting bracket as necessary to ensure

that the device will be aligned correctly on the mounting

surface.

6. Tighten the screws to secure the bracket to the spacer.

7. Disconnect power from all devices at the source and run cables through the raceway, junction box, spacer, bracket and

plastic faceplate. Connect them to the rear panel ACP ports on the device (see Step 5: Cable All Devices on page4).

8. Set the bus ID DIP switches to give the panel a unique address (see Step 4: Set Bus ID Addresses on page3).

9. Insert the device into the wallplate (see 5above) and press the entire assembly into the metal mounting bracket (6).

The ACP106EU/MK is secured to the metal mounting bracket by two catches (one on each side) and holds the wallplate in

place.

Removing ACP 106 EU or MK Wall Plates

If you need to remove an ACP 106 EU or MK wallplate from where it is

mounted, follow these steps:

1. Insert an Extron removal tool into the gap between the side of the

button plate and the plastic faceplate (see 1in the gure to the

right).

The tip of the tool should be inserted to the depth of the line marked

on the tool.

2. Slide the removal tool along the gap until the catch on the side of the

button plate (2) is released.

3. If necessary, repeat steps 1 and 2 to release the other side of the

button plate.

4. Pull the device away from the plastic faceplate. The plastic faceplate

is released at the same time.

5. Remove the screws holding the metal mounting bracket to the wall

box (3).

Cable Raceway

Junction Box

Metal Mounting Bracket

Spacer

11 2

VOLUME

MUTE

MIC

PROGRAM

Plastic

Faceplate

ACP 106 EU

VOLUME

MUTE

MIC

PROGRAM

VOLUME

MUTE

MIC

PROGRAM

Wall Box

Plastic Faceplate

Metal Mounting Bracket

ACP 106 EU

Extron

Insert

to line.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de grabación de Extron electronics

Extron electronics

Extron electronics Universal Interfaces RGB 130xi Manual de usuario

Extron electronics

Extron electronics Computer-Video Interface RGB 558 AKM Manual de usuario

Extron electronics

Extron electronics Wall and Floor Box Mountable Interfaces RGB... Manual de usuario

Extron electronics

Extron electronics Interface RGB 120p Manual de usuario

Extron electronics

Extron electronics AXI 22 AT D Manual de usuario

Extron electronics

Extron electronics RGB 112xi Manual de usuario

Extron electronics

Extron electronics RGB 560 AKM Manual de usuario

Extron electronics

Extron electronics AXI 22 AT D Manual de usuario

Extron electronics

Extron electronics VNR 100 Manual de usuario

Extron electronics

Extron electronics RGB 202 Rxi VTG Manual de usuario

Extron electronics

Extron electronics Architectural Interface RGB 440 Manual de usuario

Extron electronics

Extron electronics CVEQ1 WM Manual de usuario

Extron electronics

Extron electronics IP Link IPL T CR48 Manual de usuario

Extron electronics

Extron electronics RGB 302 Manual de usuario

Extron electronics

Extron electronics RGB 109xi Manual de usuario

Extron electronics

Extron electronics Interfaces RGB 500 Series Manual de usuario

Extron electronics

Extron electronics RGB 580xi AAP Manual de usuario

Extron electronics

Extron electronics RGB 160xi Manual de usuario

Extron electronics

Extron electronics DMP 128 Plus Manual de usuario

Extron electronics

Extron electronics VNR 100 Manual de usuario

Extron electronics

Extron electronics DMP 64 Manual de usuario

Extron electronics

Extron electronics USB-C HD 101 Manual de usuario

Extron electronics

Extron electronics CIA111 Manual de usuario

Extron electronics

Extron electronics RGB 440 Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado