Extron electronics Cable Cubby 500 Manual de usuario

IMPORTANT:

Go to www.extron.com for the

complete user guide

, installation

instructions, and specifications.

Cable Cubby 500 and 700 • Installation Guide

This guide provides instructions for an experienced installer to install and connect the Extron

Cable Cubby 500 and 700 Cable Access Enclosures.

The Cable Cubby units are furniture-mounted enclosures for cable access,

connections, and AC power. Cables that are not in use can be stored out of the

way while remaining connected to the presentation system.

Cable Cubby 500 Cable Cubby 700

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 2

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Scr

ews

ii Bk

2 4

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 2

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 2

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

(3) 3/8", (1) 1/4"(6) 3/8", (2) 1/4"

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 trim, 2 screws 2 trims, 4 screws

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 2

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

4 8

Planning

Check with local and state regulations before starting

the installation:

Ensure that the planned installation complies with building and electrical codes.

Ensure that the planned installation complies with the Americans with Disabilities Act or

other accessibility requirements.

Check all parts and equipment before installation:

Ensure that all parts are present in each kit.

Ensure that necessary tools and equipment are available for the installation.

Kit Contents

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker AC Power Module

125V~12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

Cable Cubby 500 and 700 • Installation Guide (Continued)

23.5"

(59.7 cm)

29.4"

(74.7 cm)

26.7"

(67.8 cm)

10.6"

(26.9 cm)

Table Top

XL Models

9.1"

(23.1 cm)

15.9"

(40.4 cm)

21.9"

(55.6 cm)

XL Models

3.0"

(7.6 cm)

3.0"

(7.6 cm)

Preparing the Table

Cut a hole in the surface where the enclosure will be installed. Read the following information before making a cut.

Determine the best location for the enclosure

Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.

Ensure that the edge on which the lid opens is oriented correctly.

Ensure that there is ample space under the table for cables.

When installing retractors in the Cable Cubby, ensure that there is enough space for the retractor assembly under the table or

furniture (ee dimensions for the retractors below).

Choose a method for cutting the hole in the table

ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople.

Exercise care to prevent scarring or damaging the furniture.

ATTENTION: L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et

qualiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.

CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.

ATTENTION: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut

conduire à une blessure à l’oeil.

Choose one of the following methods for cutting the hole:

Hand Router and Routing Template Jigsaw and Paper Cut-Out Template CNC Wood Router

If using a CNC wood router or other

precise machinery, use the exact

cut-out dimensions for your model

(see the table below).

Visit www.extron.com for Cable Cubby routing

template part numbers and instructions.

Dimensions and cut-out templates are

available online at www.extron.com.

Product

Cut-out Dimensions

User Access

Width

Side

Dimension

CC 500 5.75"

(14.6 cm)

5.75"

(14.6 cm)

CC 700 7.125"

(18.1 cm)

5.75"

(14.6 cm)

NOTES:

• To prevent objects from impeding cable retraction, ensure at least 3 inches of clearance from the exposed cable side of

the enclosure (see the diagrams below).

• Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or

entanglement (see Routing and Connecting Cables on page 6).

Cut-Out Template for the Extron

Cable Cubby 500

User Access

0.25"

Trim Ring

Lip Width

2.0"

TrimRing’s Outer Edge

(Do not cut this line.)

0.00”(0.00 cm)

0.02 (0.05 cm)

TableClamp

P/N 68-8599-01 Rev.A

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray) from the template.

3. Measure the cutout and template.

4. Mark the position on the

furniture where the Cable Cubby 500

will be installed.

5. Double check dimensions and position,

then cut theopening.

Page Size: 11" x 17"

Print Scale 1:1

Do not Shrink

Jigsaw

Cut-O

Cut-Out T

Cab

Preparing the Cable Cubby

Step 1 — Assemble the connectivity modules of your choice.

NOTE:

• Use a screwdriver to secure the

Retractor trim with the screws.

• After installing the retractor trim,

proceed to Step 2 — Install the

modules on the next page to

install the power module.

• Retractors are installed after the

Cable Cubby is mounted on the

table (see Installing Retractors

on page 5).

AAP Module

Cable

Pass-Through

Module

Retractor

Trim Secure the retractor trim

using the provided

mounting screws (2).

Connectivity modules allow you to populate the Cable Cubby with a combination of AAPs, cable pass-through, or retractors.

NOTE: After assembling the module,

proceed to Step 2 — Install the

modules on the next page.

NOTE: After assembling the module,

proceed to Step 2 — Install the

modules on the next page.

Secure up to two

single-space AAPs

in the AAP plate.

#4-40 Nut

w/ Captive Washer Insert cables through the bottom of the connectivity bracket.

Connect cables to the AAPs.

Secure the AAP plate on the connectivity brackets,

using two of the provided module screws.

Insert cables thr

ough the bottom of the connectivity bracket

and into the holes of the grommet plate.

Secure the grommet plate on the

connectivity bracket using two

of the provided module screws.

Snap the included hole plugs into

any unused holes.

Insert the modules into the Cable Cubby.

125V~ 12A MAXTOTAL

Secure the modules using

the provided mounting

screws and star

washers (4) on the

front and back of the

enclosure.

125V~ 12A MAXTOTAL

Step 1 — Mount the Cable Cubby ﬂush with the table.

CAUTION: The anged edges of the top of the surface enclosure are sharp. These edges are also soft and may be easily

nicked or bent. Exercise caution when handling the enclosure to prevent personal injury or damage to the enclosure.

ATTENTION: Les extrémités à brides du haut de la surface du boîtier sont aiguisées. Ces extrémités sont aussi lisses

et peuvent facilement être coupées ou pliées. Soyez prudents lorsque vous manipulez le boîtier an d’éviter de

l’endommager ou de vous blesser.

Mounting the Cable Cubby in the Table

Step 2 — Install the modules.

Determine where the connectivity modules and power module will be installed in the Cable Cubby. The modules may be installed

on the left or right side of the enclosure and at various heights.

NOTE:

• Ensure that there is enough room above the modules for the Cable Cubby lid to close completely.

• Use a screwdriver to secure the modules with the screws.

WARNING: Risk of Electric Shock. To ensure proper electrical

grounding, use the provided #6-32 mounting screws with the star

washers.

AVERTISSEMENT: Risque de choc électrique. An d’assurer une

mise à la terre correcte, utilisez les xations de mise à la terre #6-32 et

les rondelles en étoile fournies.

Lower the Cable Cubby into the hole to test the t.

If necessary, carefully enlarge the opening.

Remove the plastic strips and

lm on the surface of the

Cable Cubby.

Ensure that the

side clamps are

seated against the

enclosure.

Cable Cubby 500 and 700 • Installation Guide (Continued)

Step 2 — Under the table, adjust the side clamps on the enclosure.

Installing Retractors

NOTE: To lower the side

clamp, turn the lever

down, then press and hold

the locking plate while

sliding down the clamp.

Locking

plate

Horizontal or Angular Mounting

For installation details, see the Cable Retractor

Setup Guide available online at www.extron.com.

Secure the clip on the pin.

Insert retractors into

the retractor trim.

Secure the locking screw on each retractor.

Do not overtighten.

Insert the pin thr

ough the

etractor mounting hole on

the side of the Cable Cubby

and r

etractor assembly.

For horizontal or angular mounting, re

move

these orientation screws (front and back),

then follow the steps shown at left.

Rotate the side clamp

outward and ensure that

the lever is down.

Slide the clamp all the way

up against the bottom of

the table.

Ensure the Cable Cubby

is rmly seated in the table.

Raise the lever to secure

the Cable Cubby.

Lever

12 3

68-2491-50

Rev. B

05 14

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

Installation Checklist

Planning (page 1)

Check with local and state regulations before starting the installation.

Check all parts and equipment before installation.

Preparing the Table (page 2)

Determine the best location for the enclosure.

Choose a method for cutting the hole in the table.

Preparing the Cable Cubby (page 3)

Choose and assemble a combination of AAPs, cable-pass through, and retractor connectivity to populate

the Cable Cubby.

Secure the connectivity modules and power module in the Cable Cubby.

Mounting the Cable Cubby in the Table (page 4)

Mount the Cable Cubby ush with the table.

Adjust the side clamps.

Installing Retractors (page 5)

Routing and Connecting Cables (page 6)

Routing and Connecting Cables

CAUTION:

Risk of Electric Shock.

This equipment must be grounded.

ATTENTION:

Risque de choc électrique.

Cet équipement doit être xé au sol.

NOTE: Ensure that there is no tension on the power cable.

Secure cables with zip ties to the rectangular

holes in the rear of the Cable Cubby.

For cable pass-thr

ough applications, allow at least 36 inches (0.9 m)

of cable loop for each cable.

Connect cables to the AV system

and connect the AC power cord.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Recinto de Extron electronics

Extron electronics

Extron electronics PowerCage 411 Manual de usuario

Extron electronics

Extron electronics EWB 112 Manual de usuario

Extron electronics

Extron electronics PowerCage 401 Manual de usuario

Extron electronics

Extron electronics PowerCage 401 Manual de usuario

Extron electronics

Extron electronics Cable Cubby 300C Manual de usuario

Extron electronics

Extron electronics Cable Cubby 202 Manual de usuario

Extron electronics

Extron electronics SMB 110 Series Manual de usuario

Extron electronics

Extron electronics PVM 220 Manual de usuario

Extron electronics

Extron electronics NBP 1200C Manual de usuario

Extron electronics

Extron electronics EBP 1200C Manual de usuario

Extron electronics

Extron electronics PowerCage 1600 Manual de usuario

Extron electronics

Extron electronics HSA 400 Series Manual de usuario

Extron electronics

Extron electronics MLM-WB Manual de usuario

Extron electronics

Extron electronics HSA 822 Manual de usuario

Extron electronics

Extron electronics PowerCage 1600 Manual de usuario

Extron electronics

Extron electronics HSA 822M Manual de usuario

Extron electronics

Extron electronics TLM 100 T Manual de usuario

Extron electronics

Extron electronics PowerCage 1600 Manual de usuario

Extron electronics

Extron electronics Cable Cubby F55 Edge Manual de usuario

Extron electronics

Extron electronics HSA 200SE Manual de usuario

Extron electronics

Extron electronics CCD 220 Manual de usuario

Extron electronics

Extron electronics Hideaway HSA 200C Series Manual de usuario

Extron electronics

Extron electronics EWB 212 Manual de usuario

Extron electronics

Extron electronics Cable Cubby 300S Manual de usuario

Manuales populares de Recinto de otras marcas

SilentiumPC

SilentiumPC Armis AR5 Manual

Pulsar

Pulsar 17/TRP80/DSPR Manual de usuario

Thermaltake

Thermaltake V150 TG Manual de usuario

MSI

MSI MPG SEKIRA 500X Manual de usuario

Antec

Antec Dark fleet DF-10 Manual de usuario

Nexans

Nexans WTC05 Manual de usuario

Peavey

Peavey DS 1502 Manual de usuario

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manual de usuario

Rosewill

Rosewill RX82-U(JBOD) Manual de usuario

QNAP

QNAP SAS JBOD CLI 1.0 Manual de usuario

GAMDIAS

GAMDIAS Talos P1 Manual de usuario

Auvs

Auvs KR615 Manual de usuario

Digitus

Digitus DA-71114 Manual de usuario

CommScope

CommScope FDH 3000 Manual de usuario

FS FHD-FWME4 Manual de usuario

JBL

JBL CS1215T Manual de usuario

Pulsar

Pulsar ARAD-S4 Manual de usuario

Pulsar

Pulsar AWO454 Manual de usuario