Extreme Flight EDGE 540T EXP Manual de usuario

Thank you for your purchase of the Extreme Flight RC .40 Edge 540T Funfly. Please take a few moments

to read this instruction manual before beginning assembly. We have outlined a fast, clear and easy method to

assemble this aircraft and familiarizing yourself with this process will aid in a quick, easy build.

Please read the following paragraph before beginning assembly of your aircraft!

THIS IS NOT A TOY! Serious injury, destruction of property, or even death may result from the misuse of

this product. Extreme Flight RC is providing you, the buyer with a very high quality model aircraft compo-

nent kit, from which you, the buyer, will assemble a flying model. However it is beyond our control to moni-

tor the finished aircraft you produce. Extreme Flight RC will in no way accept or assume responsibility or

liability for damages resulting from the use of this user assembled product. This aircraft should be flown in

accordance to the AMA safety code. It is highly recommended that you join the Academy of Model

Aeronautics in order to be properly insured, and to operate your model at AMA sanctioned flying fields only.

If you are not willing to accept ALL liability for the use of this product, please return it to the place of pur-

chase immediately.

Extreme Flight RC, Ltd. guarantees this kit to be free of defects in materials and workmanship for a period of

90 days from the date of purchase. All warranty claims must be accompanied by the original dated receipt.

This warranty is extended to the original purchaser of the aircraft kit only.

Extreme Flight RC in no way warranties its aircraft against flutter. We have put these aircraft through

the most grueling flight tests imaginable and have not experienced any control surface flutter. Proper servo

selection and linkage set-up is absolutely essential. Inadequate servos or improper linkage set up may result

in flutter and possibly the complete destruction of your aircraft. If you are not experienced in this type of

linkage set-up or have questions regarding servo choices, please consult an experienced pilot or contact us. It

is your responsibility to ensure the airworthiness of your model.

Suggested tools and building materials Additional items required for assembly

Hobby knife with #11 blades 4 channel radio with 4 standard BB servos

Phillips and flat head screwdrivers 1 mini servo for throttle

Needle nose pliers .32-.53 2 stroke or .52-.72 4 stroke engine

Thin CA Propeller

30 minute epoxy Fuel tubing

Wire cutters 2.5 inch spinner

Threadlocker Foam padding for receiver and battery mounting

Drill with assorted drill bits Nylon cable ties

Tape measure 2-24 inch servo extensions

Square

Denatured alcohol

Fine tipped marker

1. Locate fuselage and remove the covering from the throttle servo mounting hole, the wing slot, the

rudder and elevator servo mounting holes and the elevator slot using a sharp #11 blade.

2. Locate the landing gear components including 4 screws, 8 washers, and 6 nylon insert locknuts.

Assemble the axle/wheel assembly first. Place a washer onto the axle screw, then insert the axle

into the aluminum landing gear from the rear side. Place another washer onto the front side of the

aluminum gear followed by a nylon insert locknut. Tighten securely. Place a wheel onto the axle

screw followed by another nylon insert locknut. Tighten until the nut is flush with the wheel, but does

not cause binding.

3. Center the landing gear between the lightening holes just below the leading edge of the wing

slot. The bend in the gear should be even with the bottom of the fuselage. If you are using a light-

weight engine you may want to angle the gear slightly forward to help achieve proper CG. Mark the

location of the two mounting holes and drill for the mounting screws. Use a washer on each side of

the landing gear and secure with the 2 nylon insert locking nuts.

4. Locate tailwheel components including tailwheel wire, tailwheel, wheel collar, and plywood trian-

gle. File a flat area onto the wire where the wheel collar will reside. Place the tailwheel onto the

wire, then the wheel collar. Use thread lock compound on the retaining screw and tighten onto the

flat area. Use a #11 blade to open the slot in the rear bottom of the fuselage. Use a toothpick or

small piece of wire to apply 30 minute epoxy into the slot. Coat the portion of the wire that will go

into the slot as well as the plywood triangle with 30 minute epoxy. Insert the wire into the slot, fol-

lowed by the plywood triangle. Use a piece of tape to secure the assembly while it dries.

5. Insert the horizontal stabilizer into the slot in the rear of the fuselage. Carefully measure to cen-

ter the stab in the slot, and measure from a fixed point on the fuselage to the tips of the stab to

ensure proper alignment. Also use a square to to ensure that the stab is perfectly square with the

fuselage. Trim the slot as needed to achieve proper alignment. Make several positioning marks on

the stab with a fine tipped marker so that it will be easy to reposition the stab when gluing it in place.

Remove the stab and using a #11 blade, carefully remove a strip of covering from the stab to allow

for a wood to wood bond between the fuselage and stab. Glue the stab into the fuselage using CA

or epoxy. Use all of the criteria mentioned above to ensure that the stab is properly aligned to the

fuselage.

6. Insert the wing into the wing slot. Using the same criteria as used for the stab, center the wing

and check for proper alignment. Again, using a fine tip marker, make several positioning marks to

aid with alignment when gluing the wing in place. Remove the wing and remove a strip of covering

to allow for a wood to wood bond between the wing and fuselage. Glue the wing into the fuselage

using 30 minute epoxy. Check to ensure proper alignment. Use denatured alcohol to remove any

excess epoxy.

7. Use a #11 blade to open the hinge slots in the ailerons/wing, stab/elevator, and rudder/vertical fin

as shown. Place CA hinges into the slots on the control surfaces and mate them to the correspon-

ding slots in the wing/stab/vertical fin. Deflect the surfaces and apply a few drops of thin CA to the

top and bottom of each hinge.

This completes the basic assembly phase of the construction process. Next we will begin

installation of the radio and engine components.

8. Next we will install the rudder and elevator servos. Use the manufacturer supplied servo hard-

ware to mount the servos in the rear of the fuselage. The elevator servo mounts in the top hole, the

rudder servo in the bottom. Use a good quality standard servo with a ball bearing supported output

shaft. We have had very good results using the Hitec HS-475 and HS-5475 digital servos in our

prototypes. The HS-225MG and the new HS-5245 digital mini servos also work well for those of you

who want to save as much weight as possible. These servos will fit in the servo holes with very little

modification. We use and recommend the Dubro super strength servo arms to achieve maximum

3D surface travel. At this time you will also want to install the throttle servo. This servo slot is cut

for a mini servo, and we use the Hitec HS-225 in this position.

9. Install the aileron servos in their cutouts in the wings. The servo output shaft should be oriented

torward the rear of the plane as shown in the picture. Use a #11 blade to open the holes for the

aileron pushrods.

10. Use a #11 blade to cut a small slit just below the leading edge of the left wing in order to pass

the throttle servo lead into the radio compartment.

11. Locate a nylon control horn and backplate, two small machine screws, one clevis, one pushrod,

one pushrod keeper and one length of heat shrink tubing from the hardware package. Screw a nylon

clevis onto the wire pushrod and attach it to the elevator servo arm. Use this to properly align and

determine the location for the elevator control horn as shown in the photo. Drill two holes through

the elevator to accept the control horn mounting screws. Use the two screws to permanently attach

the control horn to the elevator, threading through the control surface and into the nylon backplate.

Remove the pusrod and clevis from the servo arm and center the servo using your radio. Use a

piece of tape to keep the elevator in the neutral position. This time attach the clevis to the control

horn on the elevator and mark the wire to make a 90 degree bend into the servo arm. Once again

remove the pushrod and make a 90 degree bend in it where it will go into the servo arm. Cut the

pushrod off 1/4 beyond this bend. Reattach the clevis to the elevator control horn and push the

bent wire into the servo arm. Use the nylon pushrod keeper to retain the pushrod at the servo arm.

Slide the heat shrink tubing over the clevis and shrink it with a heat gun to prevent the clevis from

opening. Repeat this procedure for the rudder. The finished linkages are shown below.

12. Follow the same procedure as oulined in the previous step to determine the proper location for

the aileron control horns and consruct the aileron pushrods. Center the ailerons to the airfoil of the

wing.

13. Wrap your airborne battery pack in foam and install it into the opening in the servo tray in the

wing opposite the engine. Use nylon cable ties to secure it in place.

14. Attach a 24 inch servo extension to each of the two servos in the rear of the plane. Route both

of these extensions into the channel in the bottom of the fuselage. Use a #11 blade or moto tool

attachment to open a small slit in the bottom of the right wing to allow these two wires to pass into

the radio compartment.

15. Use a paper towel and some denatured alcohol to thoroughly clean the bottom of the fuselage.

Locate the strip of blue Oracover and iron it in place over the servo wire channel. Be sure to seal

the edges well using a medium heat setting.

16. Mount your on/off switch on top of the right wing panel near the fuselage as shown in the photo.

17. Place all of the servo wires into their proper slots in the receiver and wrap the receiver in foam.

Place the receiver into the opening in the servo tray on the opposite side of where you installed the

battery. Secure it with a nylon cable tie. Route the antenna along the bottom of the wing or along

the length of the fuselage. We usually route the antenna along the length of the wing, securing it

with a piece of clear tape at the end of the wing. We drill a small hole in the wing tip and insert the

remaining wire back into the wing to prevent it from getting in the way.

18. Locate the servo bay hatches and position them in place. Use a 1/16th drill bit to drill through

the hatches and the plywood mounting tabs in each of the four corners. Secure the hatches with the

small wood screws provided in the hardware package. Be sure to drill a hole in the hatch to allow

the antenna to pass through.

19. We have saved engine and tank mounting for last, for a reason. We will use engine position to

help achieve proper CG. Place your engine on the engine mounting rails and check to see if the air-

craft balances at the proper CG position. CG on funfly aircraft is subject to the user s preference.

We recommend you begin by balancing the Edge at 1/4 inch behind the main spar for your first

flights. This is a very conservative setting, and many of you more experienced pilots will want to use

a more aggressive set-up. Slide the engine back and forth on the phenolic mounting rails until you

achieve the recommended CG. Mark and drill the engine rails for your engine, then mount the

engine with the screws and nylon insert lock nuts provided.

20. Use the supplied short pushrod, pushrod keeper and clevis to assemble the throttle linkage

assembly as shown above. Your linkage configuration may vary depending on your engine choice.

21. Assemble the fuel tank and position it in place on the opposite side of the fuselage from the

engine. Use the 2 balsa tank stand-offs to allow the tank to clear the throttle servo. Drill 4 holes

through the fuselage, 2 on the top of the tank and 2 on the bottom. Use the 2 provided nylon cable

ties to secure the tank to the fuselage as shown in the photo. Be careful when drilling through the

fuselage that the position of the nylon cable ties does not interfere with the throttle servo. Use sili-

con fuel tubing to route fuel to the tank and muffler as recommended by the engine manufacturer.

Install your prop and spinner. This completes the construction process!

Otros manuales para EDGE 540T EXP

Otros manuales de Juguete de Extreme Flight

Extreme Flight

Extreme Flight F3A Manual de usuario

Extreme Flight

Extreme Flight 42 Vyper Bype Manual de usuario

Extreme Flight

Extreme Flight YAK-54E Manual de usuario

Extreme Flight

Extreme Flight YAK-54 ARF Manual de usuario

Extreme Flight

Extreme Flight EDGE 540 Manual de usuario

Extreme Flight

Extreme Flight Muscle Bipe ARF Manual de usuario

Extreme Flight

Extreme Flight GB1 GAMEBIRD EXP Manual de usuario

Extreme Flight

Extreme Flight LASER EXP ARF Manual de usuario

Extreme Flight

Extreme Flight MXS-EXP Manual de usuario

Extreme Flight

Extreme Flight 78" EXTRA 300 ARF Manual de usuario

Extreme Flight

Extreme Flight 91" EXTRA 300EXP ARF Manual de usuario

Extreme Flight

Extreme Flight EDGE 540T EXP Manual de usuario

Extreme Flight

Extreme Flight 110" YAK-54 V2 Manual de usuario

Extreme Flight

Extreme Flight LEGACY AVIATION 100" Turbo Bushmaster... Manual de usuario

Extreme Flight

Extreme Flight YAK-55SP Manual de usuario

Extreme Flight

Extreme Flight MXS-EXP Manual de usuario

Extreme Flight

Extreme Flight slick 580 exp Manual de usuario

Extreme Flight

Extreme Flight 78" EXTRA 300 ARF Manual de usuario

Extreme Flight

Extreme Flight VANQUISH MKII Manual de usuario

Extreme Flight

Extreme Flight 78" EXTRA 300 ARF Manual de usuario

Extreme Flight

Extreme Flight 60" Slick 580 ARF Manual de usuario

Extreme Flight

Extreme Flight EXTRA260 Manual de usuario

Extreme Flight

Extreme Flight F3A Manual de usuario

Extreme Flight

Extreme Flight Turbo Bushmaster Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario