Exalt EX-5i Lite Manual de instrucciones

EX-5i

5GHz Digital Microwave Radio

Installation & Management

Part Number: 50000005

Date: 2006-05-17

Exalt Communications Inc.

EX-5i Installation & Management

Page i

5000005

2006-05-17

Legal Notice

The information contained herein is the property of Exalt Communications, Inc. (“Exalt”) and is

supplied without liability for errors or omissions. No part of this document may be reproduced,

in any form, except as authorized by contract or other written permission from the owner.

Any brand names and product names included in this manual are trademarks, registered

trademarks, or trade names of their respective holders.

The contents of this document are current as of the date of publication. Exalt reserves the right to

change the contents without prior notice.

The publication of information in this document does not imply freedom from patent or other

rights of Exalt or others.

The Exalt logo is a trademark of Exalt Communications, Inc.

Exalt Communications Inc.

EX-5i Installation & Management

Page ii

5000005

2006-05-17

About this Document

This manual provides a complete description of the Exalt EX-5i Digital Microwave Radio and

related software. The purpose of this manual is to provide the planner, engineer, installer, system

administrator, and technician with general and specific information related to the planning,

installation, operation, management and maintenance of the device.

Revision History

Date Detail

2006-05-17 Initial release

Icons

Throughout this document, the following icons are used to denote specific types of information

as described here.

(Warning) Denotes information pertaining to potential danger to human life.

(Caution) Denotes information pertaining to potential danger to property.

(Note) Denotes information that may be particularly useful or unique

CAUTION

Exalt Communications Inc.

EX-5i Installation & Management

Page iii

5000005

2006-05-17

General Compliance and Safety

The usage of radio transmission devices is subject to specific regulatory requirements governed

by regional legislation. In most cases, the specific device must be authorized for use in a given

country and must be installed and adjusted in accordance with specific radio-frequency settings

and in a manner that has been authorized specific to the device itself in accordance with the

specific location of the device. Some users may be completely or partially restricted from use of

the device. Please consult your governmental agency/agencies for regulatory requirements before

use, or contact Exalt or your Exalt authorized dealer for assistance.

This device may not be modified in any way without the express written consent of Exalt.

Modification will not only void the manufacturer warranty, but may also be expressly illegal in

accordance to government regulations. In addition, there are no user-serviceable parts or

assemblies inside the product housing. There may also be voltages, signals and mechanisms

within the device that could be harmful to human safety.

The mounting of this device and associated peripherals and connections (inclusive of antenna

mast, antenna, cabling, egress, lightning protection devices, grounding, power, etc.) may be

subject to regional requirements for health and human safety. A qualified professional installer

and an electrician are highly recommended, and may be required by law. For example, within the

USA, this device must be professionally installed to ensure that the system implementation meets

FCC regulations.

Exalt cannot warrant the device or be found liable for any unauthorized use or installation of the

device.

Regulatory Notices

Federal Communications Commission (FCC), United States

The device is allowed to be used provided it does not cause interference to other devices. It is not

guaranteed to provide protection against interference from other electronic and radio devices.

The system has been tested and found to comply with the limits of a class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one of more of the

following measures:

•Reorient or relocate the receiving antenna.

Exalt Communications Inc.

EX-5i Installation & Management

Page iv

5000005

2006-05-17

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC

regulations.

Changes or modifications not expressly approved in writing by Exalt may void the user’s

authority to operate this equipment.

This device must be professionally installed.

In order to comply with regulations, the output power of this device may need to be adjusted in

accordance to the associated transmission system. See section 2.3 of this manual for details.

For operation within the 5725-5850 MHz band, the antenna associated with this device shall be

mounted in a location that is at least 29 feet away from humans that may be subject to long-term

or continuous exposure. For operation within the 5250-5350 MHz band, the antenna associated

with this device shall be mounted in a location that is at least 1 foot away from humans that may

be subject to long-term or continuous exposure.

Industry Canada (IC), Canada

This device complies with RSS-210 of Industry Canada. Operation is subject to the following

two conditions:

1. this device may not cause interference, and

2. this device must accept any interference, including interference that may cause

undesired operation of the device.

This device has been designed to operate with the antennas, as listed below, and having a

maximum gain of 37.9dBi. Antennas not included in the list or having a gain greater than

37.9dBi are strictly prohibited for use with this device. The required antenna impedance is 50

ohms.

Manufacturer Model # Description

Gain dBi

(mid-band)

Andrew P2F-52-N 2-foot Dish

29.4

Andrew P3F-52-N 3-foot Dish

33.4

Andrew P4F-52-NXA 4-foot Dish 34.9

Andrew P6F-52-NXA 6-foot Dish 37.6

Andrew HP2F-52-NPA 2-foot HP Dish 29.0

Andrew HP3F-52-NPA 3-foot HP Dish 33.0

Andrew HP4F-52-NPA 4-foot HP Dish 34.5

Andrew HP6F-52-NPA 6-foot HP Dish 37.2

Andrew FPA5250D06-N 6-inch Panel 18.0

Andrew FPA5250D12-N 1-foot Panel 23.6

Exalt Communications Inc.

EX-5i Installation & Management

Page v

5000005

2006-05-17

Gabriel DFPS.5-52 6-inch Panel 18.0

Gabriel DFPD1-52 1-foot Panel

23.5

Gabriel DFPD2-52 2-foot Panel

28.0

Gabriel QF2-52-N 2-foot Dish

28.5

Gabriel QF2.5-52-N 2.5-foot Dish

31.2

Gabriel QF4-52-N 4-foot Dish

34.8

Gabriel QF6-52N 6-foot Dish

37.8

Gabriel HQF2-52-N 2-foot HP Dish 28.2

Gabriel HQF4-52-N 4-foot HP Dish 34.4

Gabriel HQF6-52-N 6-foot HP Dish 37.4

MTI MT-485001 7.5-inch Panel

19.0

MTI MT-485002 1-foot Panel

23.0

MTI MT-486004 18-inch Panel

26.0

MTI MT-486001 2-foot Panel

28.0

Proxim 5054-WA-15-STN Window Panel 15.0

Radio Waves FP.5-5-18 6-inch Panel 18.0

Radio Waves FP1-5-24 1-foot Panel 23.8

Radio Waves FP2-5-28 2-foot Panel 28.0

Radio Waves SP1-5.2 1-foot Dish 22.5

Radio Waves SP2-5.2 2-foot Dish 29.0

Radio Waves HP2-5.2 2-foot HP Dish 28.6

Radio Waves SP3-5.2 3-foot Dish 32.0

Radio Waves SP4-5.2 4-foot Dish 34.8

Radio Waves SP6-5.2 6-foot Dish 37.9

RFS SPF2-52A 2-foot Dish

27.9

RFS SPF3-52A 3-foot Dish

31.4

RFS SPF4-52A 4-foot Dish

33.9

RFS SPF6-52A 6-foot Dish

37.4

RFS SDF4-52A 4-foot HP Dish 33.9

RFS SDF6-52A 6-foot HP Dish 37.4

RFS MA0528-19AN 7.5-inch Panel

19.0

RFS MA0528-23AN 1-foot Panel

23.0

RFS MA0528-28AN 2-foot Panel

28.0

For operation within the 5735-5850 MHz band, the antenna associated with this device shall be

mounted in a location that is at least 29 feet away from humans that may be subject to long-term

or continuous exposure. For operation within the 5250-5350 MHz band, the antenna associated

with this device shall be mounted in a location that is at least 1 foot away from humans that may

be subject to long-term or continuous exposure.

Safety Notices

•Review this guide in it’s entirety for important installation instructions BEFORE you

attempt to install this product.

•This product is intended to be installed, used, and maintained by experienced

telecommunications personnel only.

Exalt Communications Inc.

EX-5i Installation & Management

Page vi

5000005

2006-05-17

•A properly licensed or authorized electrician should be employed to install or

evaluate/certify the installation of all power and grounding related to the use of this

equipment and all connected devices.

•The device(s) shall only be connected to AC power sources provided by the supplier or to

DC sources within the device’s specifications. A separate breaker circuit shall be

employed at the power source.

•Lightning, surge protection devices and earth grounding are required for most

installations to ensure human safety. Consult your qualified electrician.

•Servicing of this device should be performed by authorized personnel only. Do not

disassemble this device. By opening or removing any covers you may expose yourself to

hazardous energy parts. Incorrect reassembly of this product can cause a malfunction,

and/or electrical shock, when the unit is subsequently used.

•Do not connect or disconnect the power connection to the device when the power supply

is plugged into an AC outlet. To connect, first connect the power connection to the

device, then apply power (or plug in) at the outlet. To disconnect, disengage power at the

outlet or unplug, then disconnect the direct connection to the device.

•Do not insert any object of any shape or size inside this product at any time, whether

powered or not. Objects may contact hazardous energy parts that could result in a risk of

fire or personal injury.

•Liquids shall not come in contact with, or enter the inside of the device at any time.

•Proper ventilation and/or airflow shall be provided surrounding the equipment. Do not

block any intake or exhaust vents. Items shall not come in contact with heat-sinking

materials. Assure that ambient operational and storage temperature specifications are

maintained at all times.

•Equipment is suitable for mounting on noncombustible surfaces only.

•Do not move or alter the marking labels.

Open-Source License Information

In addition to proprietary software/firmware, which is the sole intellectual property of Exalt, the

EX-5i Digital Microwave Radio makes use of public (open-source) software/firmware (such as

Linux OS) within the terms of use of their respective shared license agreements. Interested

parties may contact Exalt Communications for copies of specific license agreements for any

open-source software/firmware utilized in this product.

Exalt Communications Inc.

EX-5i Installation & Management

Page vii

5000005

2006-05-17

Exalt Limited Hardware Warranty

Exalt Communications, Inc. (“Exalt”) warrants solely to the original purchaser (“Purchaser”) that

EX-5i (the “Product”) will substantially conform in all material respects to the relevant Exalt

published specifications that apply at the time of manufacture of such Product for two (2) years

from the date of tender of Product by Exalt from FOB point designated by Exalt (the “Warranty

Period”). Proof-of-purchase in the form of an invoice, payment of invoice, or delivery waybill

must be supplied, if requested by Exalt, in case of any dispute of warranty start date. Exalt shall

within the Warranty Period, at its own option: (A) use reasonable efforts to remedy any

reproducible Product defect covered by this limited warranty within a reasonable period of time;

(B) replace the defective Product with a functionally equivalent product (repair parts and

products may be either reconditioned or new, but, if reconditioned, shall be of the same quality

as new parts or products); or (C) if Exalt determines that it is unable to repair or replace such

Product, Exalt will refund to Purchaser the amount actually paid by Purchaser for the applicable

Product. All replaced parts become the property of Exalt. Exalt may, at its sole option, refuse to

accept as defective Product that (i) is subject to the exclusions set forth below; or (ii) cannot be

demonstrated to be defective by Exalt and Purchaser is unable to provide adequate information

describing how the Product failed. Such Product will, at Purchaser’s option and expense, either

be: (a) returned to Purchaser in the state received, or (b) repaired and returned to Purchaser.

Repaired or replaced Product will be warranted for the remainder of the original Warranty

Period, but not less than ninety (90) days.

Registration

Purchaser is required to register its Product for full warranty support. Unregistered Product will

receive a Warranty Period of only one (1) year.

Exclusions

This limited warranty will not apply to: (A) any Product that: (i) has been modified or altered by

any party other than Exalt; (ii) has been subject to accident, misuse, abnormal wear and tear,

neglect, or mistreatment; (iii) has been damaged during installation of the Product; (iv) has been

damaged by the equipment or system with which the Product is used; (v) has sustained damage

to the Products’ interface or power connectors; (vi) are determined to be stolen; or (vii) has been

damaged caused by fire, power changes, other hazards, or acts of God (including without

limitation lightning); or (B) any software included in any such Product. The warranty applies

only to Products that can be identified by the Exalt trademark, trade name, serial number or logo

affixed to them. Exalt does not warrant any Product that is not manufactured by, for, or with

permission from Exalt. The Products covered by this warranty are not consumer products and

are not intended for personal, family, or household purposes.

RMA Procedures

A return material authorization (RMA) is required prior to returning Product to Exalt for

warranty or out-of-warranty repair/evaluation. As such, Purchaser must follow the following

procedures: (1) Contact Exalt (see Section 1.0 of this document for current contact data) and

request an RMA number. Please be prepared to provide the serial number of the Product, the date

of purchase, and a description of the failure that is as complete as possible; (2) Pack the Product

Exalt Communications Inc.

EX-5i Installation & Management

Page viii

5000005

2006-05-17

in its original container and packing or an equivalent; (3) Write the RMA number CLEARLY on

the outside of the shipping box; (4) For services during the Warranty Period, cost of shipment to

Exalt’s authorized service center, taxes, duty, tariffs, risk of loss and insurance charges to Exalt

shall be borne by the Purchaser. Cost of return shipment and insurance charges shall be borne by

Exalt and will be made by Exalt’s choice of carrier and method/schedule of shipment. Purchaser

may expedite return shipments, upon request, at its own expense. PRODUCTS RETURNED

WITHOUT A DULY ISSUED RMA NUMBER WILL BE RETURNED TO PURCHASER AT

PURCHASER’S EXPENSE.

THIS EXPRESS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED,

IMPLIED OR STATUTORY, REGARDING THE PRODUCT, AND EXALT, ITS

SUPPLIERS AND LICENSORS HEREBY EXPRESSLY DISCLAIM ALL SUCH IMPLIED

AND EXPRESS WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL

IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE, TITLE,

INTERFERENCE WITH QUIET ENJOYMENT, NON-INFRINGEMENT OF THIRD-PARTY

RIGHTS AND MERCHANTABILITY. FURTHER, EXALT DOES NOT WARRANT

RESULTS OF USE OR THAT PURCHASER’S USE OF THE PRODUCT WILL BE

UNINTERRUPTED OR ERROR FREE. NO WARRANTIES ARE MADE BY EXALT’S

SUPPLIERS OR LICENSORS. EXCEPT FOR THE EXPRESS WARRANTY STATED

HEREIN, THE PRODUCT IS PROVIDED “AS IS” AND WITH ALL FAULTS. THE ENTIRE

RISK AS TO SATISFACTORY QUALITY, ACCURACY, AND EFFORT IS WITH

PURCHASER.

REGARDLESS OF WHETHER ANY REMEDY SET FORTH HEREIN FAILS OF ITS

ESSENTIAL PURPOSE OR OTHERWISE, AND EXCEPT FOR BODILY INJURY, IN NO

EVENT WILL EXALT, ITS SUPPLIERS OR LICENSORS BE LIABLE TO PURCHASER

OR TO ANY THIRD PARTY UNDER ANY TORT, CONTRACT, NEGLIGENCE, STRICT

LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOST PROFITS,

LOST OR CORRUPTED DATA, COMPUTER FAILURE OR MALFUNCTION,

INTERRUPTION OF BUSINESS, OR OTHER SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF THE USE OR

INABILITY TO USE THE PRODUCT, EVEN IF EXALT HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH LOSS OR DAMAGES AND WHETHER OR NOT SUCH LOSS OR

DAMAGES ARE FORESEEABLE.

IN NO EVENT SHALL EXALT’S AND ITS SUPPLIERS’ AGGREGATE LIABILITY

EXCEED AN AMOUNT EQUAL TO THE PURCHASE PRICE OF THE PRODUCT PAID

BY PURCHASER THAT IS THE SUBJECT OF A CLAIM. ANY CLAIM ARISING OUT OF

OR RELATING TO THIS AGREEMENT MUST BE BROUGHT WITHIN ONE (1) YEAR

AFTER THE OCCURRENCE OF THE EVENT GIVING RISE TO SUCH CLAIM. IN

ADDITION, EXALT DISCLAIMS ALL LIABILITY OF ANY KIND OF EXALT’S

SUPPLIERS.

Exalt Communications Inc.

EX-5i Installation & Management

Page ix

5000005

2006-05-17

Table of Contents

Legal Notice.....................................................................................................................................i

About this Document......................................................................................................................ii

Revision History .........................................................................................................................ii

Icons............................................................................................................................................ii

General Compliance and Safety.....................................................................................................iii

Regulatory Notices.........................................................................................................................iii

Safety Notices................................................................................................................................. v

Open-Source License Information.................................................................................................vi

Exalt Limited Hardware Warranty................................................................................................vii

Section 1 – Introduction.................................................................................................................. 1

1.0 Introduction to Exalt Communications........................................................................... 1

1.0.1 Other Documentation and Software........................................................................ 1

1.1 The EX-5i Digital Microwave Radio.............................................................................. 1

1.2 EX-5i Basic Features ...................................................................................................... 3

Section 2 – Before Installation........................................................................................................ 5

2.0 Link Engineering and Site Planning............................................................................... 5

2.1 Familiarizing Yourself with the EX-5i........................................................................... 6

2.1.1 Shipping Box Contents............................................................................................... 6

2.2 Back-to-Back Bench Test and Configuration................................................................. 7

2.3 RF Output Power Setting................................................................................................ 8

2.3.1 United States........................................................................................................... 8

2.3.2 Canada..................................................................................................................... 9

2.4 Time Division Duplex Factors...................................................................................... 10

2.5 Link Orientation and Synchronization.......................................................................... 11

2.5.1 The Temporary Hardware Configuration Key...................................................... 12

Section 3 – System Installation and Initiation Process................................................................. 14

3.0 Task Overview.............................................................................................................. 14

3.1 Record Keeping ............................................................................................................ 15

Section 4 – Installation.................................................................................................................. 16

4.0 Mechanical Configuration and Mounting..................................................................... 16

4.0.1 Rack Mounting the System................................................................................... 16

4.0.2 Table or Rack Shelf Mounting the System........................................................... 17

4.1 User Interfaces.............................................................................................................. 18

4.1.1 Connector Overview............................................................................................. 18

4.1.2 Indicator Overview ............................................................................................... 19

4.1.3 Control Overview.................................................................................................. 20

4.2 Applying Power............................................................................................................ 20

4.2.1 Terminating the RF Connector ............................................................................. 21

4.2.2 AC Power.............................................................................................................. 21

4.2.3 DC Power.............................................................................................................. 22

4.2.4 Reset to Critical Factory Settings ......................................................................... 23

4.3 The Antenna/Transmission System .............................................................................. 24

4.3.1 Initial Antenna Mounting...................................................................................... 25

4.3.2 Transmission Line from Antenna to Egress.......................................................... 26

Tabla de contenidos

Otros manuales de Radio de Exalt

Exalt

Exalt ExtendAir r5015 Manual de programación

Exalt

Exalt ExtendAir r4900 Manual de programación

Exalt

Exalt ExtendAir G2 Manual de programación

Exalt

Exalt r5050 Series Manual de programación

Exalt

Exalt ExtendAir eMIMO r5050 Series Manual de usuario

Exalt

Exalt EX-4.5r GigE Manual de programación

Exalt

Exalt S Series Manual de programación

Exalt

Exalt EX-5r GigE Manual de instrucciones

Exalt

Exalt EX-2.4i Lite Manual de programación

Exalt

Exalt ExtendAir series Manual de programación

Exalt

Exalt r Series Manual

Exalt

Exalt ExtendAir series Manual de usuario

Exalt

Exalt rc06020 FCC Manual de programación

Exalt

Exalt EX-5i-DS3-GigE Manual de programación

Manuales populares de Radio de otras marcas

EisSound

EisSound KBSound iSelect Manual de usuario

Midland

Midland 1001LWX Manual de usuario

Konig

Konig HAV-SR41 Manual de usuario

Roberts

Roberts exprssion Manual de usuario

VDigi

VDigi DD3.0 Manual de usuario

Radio Shack

Radio Shack 21-1863 Manual de usuario

Roberts

Roberts Stream 207 Manual de usuario

Sony

Sony Walkman SRF-M97 Manual de usuario

Stanley

Stanley FatMax FMC770 Manual de usuario

auna

auna DAB-Radio 10026947 Manual de usuario

SOUNDMASTER

SOUNDMASTER UR190 Manual de usuario

HYT

HYT TC-320 Manual de usuario

auna multimedia

auna multimedia Yellowstone 10026851 Manual de usuario

B-Tech

B-Tech GMRS-V2 Manual de usuario

Weierwei

Weierwei VEV-V8 Manual de usuario

SOUNDMASTER

SOUNDMASTER DAB750 Manual de usuario

Telefunken

Telefunken TF-1505 Manual de usuario

Makita

Makita LXRM03 Manual de usuario