Evonicfires e1800 Manual de usuario
IMPORTANT SAFETY INFORMATION:
Always read this manual rst before aempng to install or use this replace. For your safety, always comply with all warnings and safety instrucons contained in this
manual to prevent personal injury or property damage.
Please note: This product is only suitable for well insulated spaces or occasional use.
E-Series-180724
MODEL(S): e1800 / e1560 / e1500 / e1030 / e1000 / e900 / e810 / e800 / e710 /
e700 / e640 / e600 / e500
Please read these instrucons before installaon or use and keep this booklet handy for future reference.
All Evonic res products meet the requirements of the EC Direcves.
These direcves have been met by compliance with the following standards:
EN 55014-1:2006 + A2:2011 Electromagnec compability.
EN 55014-2:2015 Electromagnec compability.
EN 61000-3-2:2014 Electromagnec compability (EMC). Limits. Limits for harmonic current emissions
EN 61000-3-3:2013 Electromagnec compability (EMC). Limits. Limitaon of voltage changes, voltage uctuaons and icker
EN 60335-1:2012 + A1:2014
EN 60335-2-30:2009+A11:2012
Safety:
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilies or lack of experience and knowledge if they have
been given supervision or instrucon concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision
The instrucons shall state that the heater must not be located immediately below a socket outlet.
WARNING: in order to avoid overheang, do not cover the heater.
Children of less than 3 years should be kept away unless connuously supervised
Children aged from 3 years and less than 8 years shall only switch on/o the appliance provided that it has been placed or installed in its intended normal operang posion and they have
been given supervision or instrucon concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
CAUTION: Some parts of this product can become very hot and cause burns. Parcular aenon has to be given where children and vulnerable people are present
CAUTION: In order to avoid a hazard due to inadvertent reseng of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a mer,
or connected to a circuit that is regularly switched on and o by the ulity
CAUTION: The LED light system shall be replaced by electrically competent personnel only (LP – These cannot be user replaceable since they will allow access to live parts)
IMPORTANT INSTRUCTIONS:
Important electrical safety:
This appliance must never be installed above or in front of a xed electric socket.
The electrical socket must be easily accessible to isolate the supply during maintenance and cleaning.
This appliance is supplied with a two meter power lead, which has a 13Amp moulded three pin plug to connect to a standard 230/240V plug socket.
This appliance must always be earthed. If in any doubt consult a suitably competent person.
Replacement plug: (Please note that it will invalidate your warranty if the moulded plug is removed and connected to a fused spur by an unqualied person).
General Warnings:
Never leave children unsupervised with an unguarded heater.
Never obstruct or cover the heater outlet.
Never install or use this product where it may come in contact with water i.e. a bathroom or wet room.
Never use aerosols or steam cleaners near this product.
Never route the electric cable near the heater outlet.
Never route the electric cable under carpets or oor coverings.
Never install this product close to curtains or combusble materials.
Never Use the heater to dry clothes or other objects.
Never remove the replace surrounding without isolang the electric supply.
Fig:1.
This appliance must only be connected to a 230/240 Volts AC 50Hz supply. Before connecng the re, check that the supply voltage is the same as stated on the re.
This appliance must only be used on a AC supply, fuse rang 13Amp.
The wires in the mains lead are coloured in accordance with a standard UK supply, these being:
GREEN/YELLOW – EARTH
BLUE – NEUTRAL
BROWN – LIVE
As the colours of the mains lead of this appliance may not match the coloured markings used to idenfy the terminals in a plug, please observe the following (Fig:1).
• The green and yellow wire must be connected to the terminal in the plug which is marked with the leer E or Earth symbol.
• The blue wire must be connected to the terminal in the plug which is marked with the leer N.
• The brown wire must be connected to the terminal in the plug marked with the leer L.
• Replace fuses only with fuses of the correct size and rang.
This product has been designed to be installed into a plaster board, or exisng masonry chimney breast.
Please note that any GF2 models from the e-series range are not suitable to be installed into a exisng chimney breast.
Please seek advice from a professional, with reference to the structural integrity of the installaon site.
if the products is to be installed into a open chimney or ue, it is important that the chimney/ue is blocked o to prevent any up/down draughts and falling debris which could restrict
and alter the airow to the product.
It is also important to ensure that the product has a minimum internal clearance directly above and below the product of 50mm, this is to ensure that the product can circulate the re-
quired airow for the heater unit.
The product should never be sealed into a opening with the use of silicones or adhesives as this can also alter the airow and hinder any further servicing of the product.
INSTALLATION METHOD:
Installing Product:
Each E-Series product is supplied complete with one or more wall mounng brackets. (Dependent on Model)
Establish the desired nished height from oor level to the boom of the plaster kit of the product.
Fix the wall bracket to the wall ensuring to use the correct hardware xings given the wall construcon, Plaster board or Solid Wall.
Li and hook the product onto the wall bracket and secure using the wall brace brackets.
Once the product is secured to the wall and connected to the power supply, the false construcon such as plaster board wall or chimney breast can be formed around it.
It is important to allow for the nished face board when seng the depth of the frame construcon.
It is essenal to include header/Lintel at the required height to ensure the appliance does not support the weight of the nished wall.
Prepare the Cut-Out in the Plaster-board or Finishing Board, and install ensuring that the plaster kit edges are ng to the inside of the Cut-out of the board.
The above table contains the minimum opening sizes re-
quired to house the product.
Please refer to technical specicaon table for further informaon, with reference aperture measurements.
Please see Figure 1: as a example of a installaon.
Figure 1:
Model WDH
e500 530mm 305mm 610mm
e600 690mm 185mm 640mm
e640 508mm 185mm 845mm
e700 680mm 185mm 480mm
e710 760mm 185mm 790mm
e800 835mm 305mm 790mm
e810 866mm 305mm 1209mm
e900 886mm 185mm 695mm
e1000 1055mm 185mm 475mm
e1030 1065mm 305mm 560mm
e1500 1565mm 305mm 560mm
e1560 1566mm 305mm 810mm
e1800 1785mm 305mm 615mm
Model WDH
e500 495mm 305mm 400mm
e600 637mm 185mm 455mm
e640 460mm 185mm 655mm
e700 640mm 185mm 285mm
e710 710mm 185mm 607mm
e800 802mm 305mm 590mm
e810 810mm 305mm 1003mm
e900 836mm 185mm 492mm
e1000 1003mm 185mm 275mm
e1030 1003mm 305mm 355mm
e1500 1505mm 305mm 355mm
e1560 1509mm 305mm 605mm
e1800 1750mm 305mm 410mm
The below table contains the nal nished opening sizes once
the product has been installed.
Glass Removal:
The Appliance is operated using the E-Touch App Control.
The App Control can be used on either OS or Android operang systems.
To obtain the App please visit either the OS App Store Or Google Play and follow the on screen instrucons.
Screen shot taken from Apple App Store. Home Screen shot taken from E-Touch App
Product Operaon:
The appliance is operated by the e-touch App, the main standby power switch to the e-series product is located to the right of the heater outlet, which is marked with a light bulb image, to
acvate the product, this switch must be switch to the “ON” posion.
The rst me the e-series product is acvated both the illuminaon and heater will funcon, to switch the heater “O” simply reduce the Room Temperature down to 10 degrees on the
App control.
BUILT IN MODELS:
This product has been designed to be installed into a studwork or exisng chimney breast.
Please note that any GF2 models from the e-series range are not suitable to be installed into a exisng chimney breast.
Please seek advice from a professional, with reference to the structural integrity of the installaon site.
If the products is to be installed into a open chimney or ue, it is important that the chimney/ue is blocked o to prevent any up/down draughts and falling debris which could restrict
and alter the airow to the product.
It is also important to ensure that the product has a minimum internal clearance directly above and below the product of 100 mm, this is to ensure that the product can circulate the
required airow for the heater unit.
The product should never be sealed into a opening with the use of silicones or adhesives as this can also alter the airow and hinder any further servicing of the product.
Please refer to technical specicaon table for further informaon, with reference to measurements.
(Heater unit cut-out) (This is a safety feature, to safe guard against further damage to the product).
If the airow is restricted the heater will automacally turn o. This is can occur due to incorrect installaon or obstrucon.
To reset the heater funcon:
•isolate from the mains power supply.
•Leave product to cool.
•Aer a suitable cooling down period, remove the obstrucon if obstructed, and check installaon.
•Aer 10 minutes the thermo switch (cut-out) in the heater will reset.
Please note that both the eect fan and heater fan omit a low decibel noise, both of which are normal operang characteriscs.
LOG LENGTH
A260MM
B370MM
C230MM
D185MM
E190MM
F390MM
e1000/1030 —LOG LAYOUT
e1500/1800 —LOG LAYOUT
LOG SET
Please Note: The images shown are suggested Log layouts, the log sets can
be arranged to personal preference.
Condions of warranty:
If this appliance should prove to be defecve due to faulty design, materials or workmanship within 12 months of purchase, the product will be repaired free of charge, subject to the
following condions:
The electric re shall have been purchased and used solely within the UK and Ireland for domesc purposes and in accordance with the Users operang instrucons.
It is the purchasers responsibility to prove that the unit is under warranty, e.g. receipt of purchase.
All warranes, will be invalidated if unauthorised repairs or modicaons are made to the electric re, or in case of accident, misuse or damage caused by improper installaon, or to
damage occurring during transit to or from the repairer and altered or missing serial numbers.
Any parts, which have been replaced under this warranty, shall become our property.
CK Fires Ltd / Evonic Fires
1 Evonic house, Clifford park, Clifford lane, Stratford-Upon-Avon, CV37 8HW
Tel: +44 (0) 1789 263868 Fax: +44 (0) 1789 293080
Problem solving
• No power to the re: Check the wall socket, plug and fuse.
• No illuminaon: Make sure the re is turned on. Check heater is working, if so check that the dimmer control is set to full on the e-touch app/e-touch controller.
• Illuminaon but no heat: The safety cut has operated see note on operang the Fire.
• Noise when illuminated: Due to moving parts, the electric re will make a noise.
• Noise from the heater when in use: The sound of rushing air is normal.
Registering product:
To register a product please visit: www.evonicres.co.uk and complete the elds required under the Register a Product Secon.
Report a fault:
If a product is encountering a fault with the operaon and a Service Engineer is required, Please visit: www.evonicres.co.uk and complete the elds required under the Report a Fault
Secon.
Otros manuales para e1800
1
Este manual sirve para los siguientes modelos
13
Tabla de contenidos
Otros manuales de Chimenea de interior de Evonicfires
Evonicfires
Evonicfires Cubbington 1350 Manual de usuario
Evonicfires
Evonicfires e500 Manual de usuario
Evonicfires
Evonicfires E1030DS Manual
Evonicfires
Evonicfires Evoflame E32H Manual
Evonicfires
Evonicfires e500 Manual de usuario
Evonicfires
Evonicfires E Series Manual de usuario
Evonicfires
Evonicfires SIGMA Guía de configuración
Evonicfires
Evonicfires Arizona Instrucciones de montaje
Evonicfires
Evonicfires CANTO 200 Manual de usuario
Evonicfires
Evonicfires Stora DS Manual de usuario
Evonicfires
Evonicfires Evoflame E500 Manual de usuario
Evonicfires
Evonicfires Aaren Manual de usuario
Evonicfires
Evonicfires NEWTON Manual de usuario
Evonicfires
Evonicfires E800T Manual de usuario
Evonicfires
Evonicfires EVOFLAME Manual de usuario
Evonicfires
Evonicfires Alisio 850 Manual de usuario
Evonicfires
Evonicfires EVOFLAME E810 DS Manual de usuario
Evonicfires
Evonicfires Halo Tyrell Manual
Evonicfires
Evonicfires Aaren Manual de usuario
Evonicfires
Evonicfires Amathus Manual de usuario
