EUROPRO 0701AREN30MAS Manual de usuario

EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET - Tél : +33 (0)4 42 29 08 96 – Fax : +33 (0)4 42 53 44 36

SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510

User manual

Edition of 07/04/2020

Mini-Sandblaster 30L

INSTRUCTIONS AND MAINTENANCE MANUAL

INDEX

THANKS.................................................................................................................................................... 2

1. MANUAL AIMED TO............................................................................................................................. 3

2. INFORMATION REMARK..................................................................................................................... 3

3. GUARANTEE........................................................................................................................................ 4

4. WASTE PRODUCTS AND ENVIRONMENT........................................................................................ 4

5. EQUIPMENT DESCRIPTIONS ............................................................................................................. 4

5.1. GENERAL DESCRIPTION.............................................................................................................................4

5.2. MAIN COMPONENTS....................................................................................................................................5

5.3. IDENTIFICATION PLATE...............................................................................................................................6

5.4. TECHNICAL FEATURES ...............................................................................................................................7

5.5. REGULATION ................................................................................................................................................7

5.6. SAFETY SYSTEMS........................................................................................................................................8

6. EQUIPMENT INSPECTION WHEN RECEIVED................................................................................... 8

7. USE INSTRUCTIONS ........................................................................................................................... 9

7.1. PRIOR OPERATIONS....................................................................................................................................9

7.2. TANK LOADING.............................................................................................................................................9

7.3. WORKING PRESSURE REGULATION .........................................................................................................9

7.4. ABRASIVE PRODUCT OUTLET REGULATION..........................................................................................10

7.5. CONTROL OF THE ABRASIVE OUTLET ON LEAVING SANDING............................................................10

8. COMPONENTS DISMANTLE............................................................................................................. 11

8.1. TIPS DISMANTLE ........................................................................................................................................11

8.2. PRODUCT HOSE DISMANTLE ...................................................................................................................11

8.3. TANK TOP DISMANTLE ..............................................................................................................................11

9. PIECES OF ADVICE TO AVOID INAPPROPIATE AND DANGEROUS PRACTICES..................... 12

10. COMPLETE SPARE PARTS DISMANTLE...................................................................................... 14

TROUBLESHOOTING ............................................................................................................................ 17

12. EQUIPMENT STORAGE................................................................................................................... 18

13. EQUIPMENT WITHDRAW................................................................................................................ 18

14. INSPECTIONS AND PERIODICAL TESTS...................................................................................... 18

CONFORMITY DECLARATION ............................................................................................................. 19

THANKS

EUROPE PROJECTION wants to thank the confidence shown in the acquired

precision sandblaster.

This trust motivates us to keep working daily for the consecutions of the highest quality

criteria of our products, to such an extent that they have became a reference on reliability and

exigencies fulfilling in the market aimed to.

Hoping the acquired product is of your complete satisfaction and being at your entire

disposition to assist any consultation or suggestion, please receive again our most sincere

thanks.

SANDBLASTER 0701AREN10MAS

1. MANUAL AIMED TO

EUROPE PROJECTION has elaborated the here shown Instructions manual and

maintenance as a document recommended to be attached to the precision sandblaster

for its whole useful life, considering it as other component of this one.

The Manual is aimed to the end user and technical assistant of the equipment and it

contains every useful information on safety related to:

Assembly

Fine tuning

Use

Manteinance, including testing by the end user

Dangers caused by an inappropiate use

2. INFORMATION REMARK

This document must be at disposal of the staff using and maintaining the equipment.

In order to assure that equipment features are the same as the ones specified in your

order, please, revise it when received and contact the authorized TAS (Technical Assistance

Service) in case you find any disagreement.

For these reasons, it is recommended that every repairing or substitution of

components into the equipment is done directly by specialized staff (Consult the manufacturer

for local Technical Service)

ATTENTION:

Any modification in the original configuration of the equipment or its components, as

well as its use to a different aim for which it has been designed, will imply the

immediate invalidation of the product homologation. This will free EUROPE PRO-

JECTION from any responsibility as manufacturer enterprise of the commercialized

equipment.

Moreover, the homologation invalidation will be caused by:

Welding operations on the pressure device.

Mechanization operations (drills, cuts, etc.)

Different assemblies to the original one

Substitution of elements different to the original ones

Safety valve manipulation



The following actions will cause a breakdown which is be covered by the guarantee:

To work with wet abrasives or with measures higher to recommended.

To put the machine in horizontal position with the tank full of abrasive

To fill the tank with abrasive till the very top.

To use the equipment near of the air compressor

INSTRUCTIONS AND MAINTENANCE MANUAL

3. GUARANTEE

The acquired equipment counts on a two years guarantee from the Invoice date. The

guarantee covers manufacturing defects and faults in components.

Elements repairs and substitution are only guaranteed if made by technical staff of

EUROPE PROJECTION or Official Technical Service.

Defectives pieces will be sent carriage paid.

The guarantee does not cover direct or indirect damages caused by our machine on

people or things, neither repairing operations made directly by the client or third people.

Guarantee does not cover:

Breakdowns or damages caused by an inappropiate use of the equipment.

Breakdowns or damages caused by spare parts different to the original ones

or recommended by EUROPE PROJECTION.

Breakdowns or damages caused by a wrong conservation.

Components subject to wear (tips, filters, hoses, etc.).

Guarantee is null:

When repairs and components substitutions are done in the equipment, without prior

authorization from EUROPE PROJECTION.

When the serial number identifying unequivocally every equipment is manipulated or

removed.

When breakdown is proved to be caused by an inadequate use of the equipment, by

a fall or a hit, or by causes not due to normal working conditions.

When the equipment is dismantled, manipulated or repaired without the authorization

of EUROPE PROJECTION.

Repair operations made on guaranteed equipments will not mean stop or extension of

guarantee period.

4. WASTE PRODUCTS AND ENVIRONMENT

5. EQUIPMENT DESCRIPTIONS

5.1. GENERAL DESCRIPTION

The bought equipment is a precision sandblaster aimed to small and medium precision

workings on decoration, metal or wood industry; based in the application of abrasive products

on the surface to be treated.

Amongst the possible applications we can find:

Wall cleaning

Wood stripping

REMEMBER:

To get rid of pollutant and dangerous products, of packages, of equipments and

tools into disuse and in general of any type of waste produced by its activity, please

go to the Selective Collection and Treatment points suitable for each case.

If you need any information related to this, please go to the Environmental ministry

in your regional government or to the nearest city hall

SANDBLASTER 0701AREN10MAS

Paper and adhesive removing

Swimming pool stripping

Graffiti removing

Concrete cleaning and fitting

Plastic cleaning

Paving and flooring mark removing

Metallic surfaces preparation

Tank and metallic container clearing and stripping

This sansblaster allows us the application of the following types of abrasives: corindon,

metallic grain, glass, aluminium silicate, garnet, calcium carbonate and silica sand (grit).

Next, it is attached a table which will help the end user to choose the abrasive size

according to tip diameter.

Tip (mm)

Abrasive Granule Diam. (mm)

Minimum

Maximum

2,0

0,25

0,40

2,5

0,25

0,50

3,0

0,25

0,60

4,0

0,25

1,00

Table 1

The reference of the precision sandblaster model acquired is 0701AREN10.

5.2. MAIN COMPONENTS

Main components in the equipment are here shown graphically and listed.

Posit.

Denomination

Tank with wheels

Top

Product inlet

Regulation box and system

Working pressure regulador

Abrasive product outlet

Product outlet flow rate regulator

Product hose

Remote control circuit (pneumatic)

Safety valve

Air inlet to equipment

Gun

Carriage handle

Handle clamp

Handle clamp housing

Air inlet to tank

Cap

Purifier filter

INSTRUCTIONS AND MAINTENANCE MANUAL

Manometer

Air tank release

Table 2

5.3. IDENTIFICATION PLATE

Spare parts 1 –Main components

SANDBLASTER 0701AREN10MAS

The equipment is fitted with a identification plate that, under any case, can´t be

removed or manipulated.

The identification plate provides the following information:

Manufacturer name

Serial number and manufacturing date.

Main characteristics.

Other compulsory data, according to application regulation.

To make any enquiry to EUROPE PROJECTION, related to the equipment, it will

be neccessary to refer to the serial number on the identification plate.

5.4. TECHNICAL FEATURES

The precision sandblaster technical features are shown in the

table as follows:

0701AREN30MAS

Weight

31,5 kg

Tank capacity

30 l.

Min. working pressure

2 kg/cm2

Max. working pressure

6 kg/cm2

Optimal working

pressure

4 –5,5 kg/cm2

Required air flow rate

(compressor)

250 –450 l./min. (Boquilla 2)

350 –600 l./min. (Boquilla 2,5)

700 –1000 l./min. (Boquilla 3)

1200–1400 l./min.(Boquilla 4)

Safety pressure

6 kg/cm2

Air inlet connection

CR 3/8 / Racor Expres Din 3489

Working temperatura

de 0 a 50º C

Tip material

Carburo de tungsteno

Size

500x430x940 mm (with carriage

handle)

Table 3

5.5. REGULATION

The precision sandblaster has been designed, manufactured, inspected, tested and

commercialized, under the compliance of the following regulation:

EUROPEAN DIRECTIVE

97/23/CE

Relative to pressure equipments

HARMONIZED EUROPEAN REGULATION

EN 13445-1:2002

Pressure tank not subjected to flame action. General issues.

EN 13445-2:2002

Pressure tank not subjected to flame action. Materials

EN 13445-3:2002

Pressure tank not subjected to flame action. Design

EN 13445-4:2002

Pressure tank not subjected to flame action. Fabrication

EN 13445-5:2002

Pressure tank not subjected to flame action. Inspection and testing

Table 4

INSTRUCTIONS AND MAINTENANCE MANUAL

5.6. SAFETY SYSTEMS

5.6.1. SAFETY VALVE

The sandblaster is fitted as standard with a safety valve [Spare parts 1 –Posit.10] installed

on the top of the tank [Spare parts 1 –Posit.2], in order to never exceed the maximum working

pressure for which it has been designed (6 kg/cm2). If it exceeds the safety pressure, the valve

will unload the pressure excess.

No manipulation in safety valve or its seal may be done. Any valve alteration can

cause serious damages to user and alter the correct functioning of the equipment.

EUROPE PROJECTION is free from any responsibility derived from any

manipulation in valve by the user, which will support this responsibility.

5.6.2. DEPRESSURE SYSTEM

The sandblaster is fitted with a three via with piloting [Spare parts 2 –Posit.41] placed in

the inside of the regulation box [Spare parts 1 –Posit.4]. The pneumatic remote control system

[Spare Parts 1 –Posit.9] has been designed so that with no piloting signal (gun trigger [Spare parts 2

–Posit.58] released), the air inlet via to tank gets closed, so at the same time it is depressurized

through the exhaust of the antireturn valve installed on the top of the equipment [Spare parts 1 –

Posit.20].

6. EQUIPMENT INSPECTION WHEN RECEIVED

Before using the equipment, we have to ensure that it has not suffered any damage

during the carriage or storage. Moreover, we must check that every component and

accessories composing the equipment are into the package.

The basic equipment includes the following components:

Sandblaster unit (tank with wheels, top, regulation and safety valve systems)

Carriage handle

Gun

Tungsten carbide tip 3 mm

5 m product hose

10 m pneumatic remote control circuit (5 m to gun+ 5 m return)

Hopper with extension

Identification plate

Instructions and maintenance manual

Gloves

Basic protection mask

Disposable celulose hood (2 unit.)

Hearing protection, ear plugs

You must check that Serial number in the equipment coincides with the one appearing

in the delivery document.

WARNING:

Once the gun trigger is released of finger action [Spare parts 2 –Posit.58], we must wait

about 10 seconds to assure that tank depressurization has been completed.

SANDBLASTER 0701AREN10MAS

7. USE INSTRUCTIONS

7.1. PRIOR OPERATIONS

Before starting the equipment, we must do the following operations:

To drain the air feeding hose to eliminate possible water condensations.

To check that compressor is capable to supply the air flow rate required. The air flow

rate depends on the type of work to be done (working pressure), that can be between

700 –1000 l/min for the tip standard 3.

To check that every hose are in good condition (with no cracks no folds).

To check that connection of air feeding inlet is in good condition.

To check that water purifier filter [Spare parts 1 –Posit.18]is not full. As drain in not

automatic, you should drain it regularly.

To place the carriage handle [Spare parts 2 –Posit.47] which is received dismantled.

To fix the handle, slide the handle [Spare parts 2 –Posit.47] through the tubes welded to to

the body of the boiler and place the handle clamp [Spare parts 2 –Posit.61] .

To connect the air feeding hose to equipment.

7.2. TANK LOADING

To load the tank, you must follow the following steps:

To assure that tank is depressurized (manometer view [Spare parts 1 –Posit.19]).

To disconnect the equipment from compressor.

To unscrew the plastic cap [Spare parts 1 –Posit.17] located in the product inlet [Spare

parts 1 –Posit.3].

To introduce the hopper with extension in the loading hole [Spare parts 1 –Posit.3]

pressing into the inner product lid [Spare parts 2 –Posit.13], and so, it will be opened.

To pour the abrasive product inside the tank until reach the wanted fill level.

To remove the hopper, allowing the inner product lid [Spare parts 2 –Posit.13] locks

automatically thanks to the spring system.

To check that there is no abrasive product on the loading hole causing lack of air

tightness on the locking or unnecessary joint wear [Spare parts 2 –Posit.3].

To screw plastic cap [Spare parts 1 –Posit.17] into the original position.

To connect again the equipment to compressor.

The type of abrasive product (sand, metallic grain, glass, corindon, etc.) to be used, as

well as the granule diameter, depends on the type of work. To help to choose the abrasive

size according to tip diameter, please check Table 1.

7.3. WORKING PRESSURE REGULATION

Working pressure can be adjusted operating manually the regulator [Spare parts 1 –

Posit.5], located in the regulation box [Spare parts 1 –Posit.4].

The regulator can be operated with the equipment on.

To activate the regulator you must follow the following steps:

To raise the regulator control

To turn the control until reaching the appropiate working pressure which is shown

in the manometer.

INSTRUCTIONS AND MAINTENANCE MANUAL

To push the control again down to click the regulator.

Working pressure must never exceed 6 kg/cm2(max. pressure on safety valve).

Optimal pressure range is considered from 3,5 to 5,5 kg/cm2.

Working pressure depends on the type of work we want to do.

7.4. ABRASIVE PRODUCT OUTLET REGULATION

The abrasive product outlet can be regulated by operating manually the regulation

control of the product outlet [Spare parts 1 –Posit.7], placed in the lower part of the tank.

The beginning of the adjusting must be done with the regulator completely closed

(control totally tight), and you must open slowly and gradually until reaching the flow rate

suitable for the type of work to do. The adjusting process must be done with the gun trigger

[Spare parts 2 –Posit.59] pushed.

7.5. CONTROL OF THE ABRASIVE OUTLET ON LEAVING SANDING

The sandblaster has a valve in the tank cover [Exploded View 2 - Posic.94] to control

the abrasive outlet when the trigger is released.

In normal operation, the valve must be open to prevent the appearance of abrasive jets

when starting to sand and at the end.

WARNING:

Do not dismantle the regulation screw with the equipment on. Once the maximum

flow rate is reached, you must not keep turning the regulation screw [Spare parts 1 –

Posit.7] to opening, as it could be accidentally dismantled.

WARNING:

If for safety, it is necessary that the abrasive stops immediately when the trigger is

released. It is necessary, lock the key on the tank cover [Exploded view 2 - Posic.94].

Tabla de contenidos

Otros manuales de Herramientas eléctricas de EUROPRO

EUROPRO

EUROPRO SANDBLASTPRO 30L Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual