EuropAce Otimmo ECH 5141S Manual de usuario
DELUXE SLIM HOOD
ECH 5141S
Thank you for purchasing EuropAce Products.
Thank You For Purchasing EuropAce Designer Slim Hood.
DELUXE SLIM HOOD
ECH 5141S
by EuropAce
ithout
r of the
Table of Contents
From the Manufacturer 3
Specifications 3
SAFETY : Read this first ! 4. 5
Vent System Requirement 5
Description of Parts 6
Ducted vs. Re-circulating modes 7
Setting 8
Installation 9, 10
Electrical Connection 11
Operation 12
Cleaning & Maintenance 13
Troubleshooting 14
Schematic Diagram 15
3
From the Manufacturer
This appliance and it’s packaging are produced by processes
that minimize waste and respect the environment.
Please help us to continue the protection of the environment by
disposing of the packaging in a correct manner.
Safety !
Please do not allow young children to play with the plastic bag
packaging.
Before disposing of any old appliances, be sure to cut off the
power chord so that others will not be endangered by a defec-
tive electric appliance
Specifications
Input :
2 motor version :
LED Lamps :
220-240V 50Hz
2 X 85W
2 X W
Total Power
2 motor version : W
External Dimensions
90cm version : 898x508x130mm
4
SAFETY : Read this First !
Do not connect the appliance if there are obvious signs of transportation dam-
age.
Read this user manual thoroughly before attempting to use this appliance.
Installation and repair should be attempted only by qualified technical personnel.
It is dangerous to modify any part of this appliance.
The manufacturer declines all responsibility in case of failure to adopt proper
safety measures.
Ensure the location in which this appliance is installed has good, permanent ven-
tilation.
The distance between the bench top to the lower part of the hood must not be at
less than 65 cm or higher than 75 cm.
Use an electrical connector with earth that is correct for your location.
Check that the voltage in your area is correct before plugging in.
The electrical connection of this appliance must be connected as follow.
Blue = NEUTRAL
Brown = LIVE
Multiple plugs and extension cables must not be used. Overload is dangerous
and may cause a fire.
Ensure that the power supply chord is free from any heat source or sharp ob-
jects.
The appliance should be switched off and the electrical supply disconnected be-
fore any cleaning or maintenance work can be carried out.
This appliance is not intended for use by persons (including children) with re-
duced physical, sensory or mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety. Children should be super-
vised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its
Operation
The hood is equipped with 3 speed control.
Use the low speed for simmering, medium speed for light cooking.
Use the high speed for frying or heavy cooking.
It is also equipped with a light bulb to illuminate you cooking area
when needed.
Light On/Off Button (i)
On/Off switch for the light. Push the button in to turn the light ON,
push again to turn the light OFF.
Blower Off Button (ii)
Off switch for the blower. Push the button in to turn the blower OFF.
Blower On and Speed Buttons (iii, iv & v)
Button (iii) operates the blower on LOW speed.
Push button (iv) for MEDIUM speed.
Push button (v) for HIGH speed.
12
i ii iii iv v
5
SAFETY : Read this First ! (Continued)
Service agent or similarly qualified persons in order to avoid a hazard.
There shall be adequate ventilation of the room when the range hood is used at the
same time as appliances burning gas or other fuels (not applicable to appliances that
only discharge the air back into he room);
There is a fire risk if cleaning is not carried out in according with the instructions.
No flame allowed under the range hood.
The appliance supports maximum 4 hob element .
Vent System Requirements
Determine which venting method is best for your application. Vented (non-
recirculation) system must be terminate to the outside. Ductwork can extend either
through the wall or the roof. Do not terminate the vent system in an attic or other
enclosed area.
The length of the ductwork and the number of elbows should be kept to a minimum
to provide efficient performance. The size of the ductwork should be uniform. Do
not install two elbows together. Use duct tape to seal all joints in the ductwork sys-
tem. Use caulking to seal exterior wall or floor opening around the cap.
Flexible ductwork is not recommended. Flexible ductwork creates back pres-
sure and air turbulence that greatly reduces performance.
Make sure there is proper clearance within the wall or floor for exhaust duct before
making cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or
stud must be cut, then a supporting frame must be constructed.
6
Description of Parts
7
Ducted vs. Re-circulating
Your cooker hood can be configured to operate in the ducted or re-circulating
mode :-
A. DUCTED MODE (VENTED MODE)
In the ducted mode, cooking fumes are vented outdoors through suitable
connection of 125mm diameter. In this mode, only the aluminum filters
are installed, charcoal filter is optional.
B. RE-CIRCULATING MODE
Fumes are filtered for grease and odour through the aluminum grease
filters and the charcoal filters respectively and re-introduced into the
kitchen environment. In re-circulating mode, both the aluminum grease
filters and the charcoal filters must be installed.
8
Setting
The operating mode of your cooker hood must be set before installation
A. To set your hood to operate in the ducted mode
By adjusting the plastic parts on the motor housing as per below arrow
showed.
B. To set your hood to operate in the re-circulation mode
By adjusting the plastic parts on the motor housing as per below arrow
showed.
9
Installation
Mounting accessories included
4 screws 5 x 44mm
4 wall plugs (brick fixing) Ø 8mm
4 screws 4,2 x 35 mm
Installation (1) — Wall unit mounting
(1) Using the drilling temple.
(2) Make the holes on the bottom of the cupboard.
(3) If the hood is to be used in the extraction version.
(4) Make a hole for the exhaust pipe.
(5) From inside the cupboard, insert the 4 supplied screws.
(6) And tighten them in the appropriate holes on the appliance.
10
Installation (2) — Wall Mounting
(1) Mark a centre line on the wall.
(2) Fit the template onto the wall.
(3) Fix the drilling template to the wall. Make 3 Ø 8mm holes in the wall.
(4) 2 at upper points, 1 as desired at lower points. Insert the three Ø 8mm expan-
sion plugs into the wall.
(5) (brick fixing only..) Insert two 5 x 45 screws.
(6) But do not tighten them completely, hang the hood.
(7) Tighten the 2 upper screws.
(8) From inside the hood, insert the third 5 x 45 screw into the lower hole.
(9) And tighten.
Tabla de contenidos
Otros manuales de Campana de ventilación de EuropAce
