EURO EA120BTSX Manual de usuario

User Manual and

Installation Instructions

Model：

：：

： EA120BTSX Model：

：：

：EA120BIS

Model：

：：

： EA90BTSX Model：

：：

：EA90BIS

For Outdoor use only.

Read the instructions carefully and be sure your barbecue is properly installed, assembled and cared for.

Failure to follow these instructions may result in serious bodily injury and/or property damage.

Please retain the manual for future reference.

These BB s are configured for use with Propane Gas, however are also approved for use with Natural Gas. If

you prefer to connect the BB to Natural Gas, the BB needs to be configured for Natural Gas. Converting

this BB to Natural Gas must only be done by an authorized person and with a Natural Gas conversion kit

supplied by Eurostyle. Please contact Eurostyle to purchase a Natural Gas Conversion kit.

Remove any transit protection before using.

Please

DO NOT use the two solid hot platestogether.

NOTE TO INSTALLER: TEST OPERATION OF THE APPLICANCE AND INSTRUCT THE USER BEFORE LEAVING.

Service & Spare parts

Your applianc should b s rvic d annually by a comp t nt authoris d p rson

For s rving or spar parts or Natural Gas conv rsion kit, pl as contact

Eurostyl Group trading as Euro Applianc s

S rvic lin : (08) 81651012

Fax: (08) 8165 1018

Email: admin@ urostyl group.com.au

USE

OUTDOORS

ONLY

This appliance shall only be used in an above ground open-air situation with natural ventilation, without stagnant areas,

where gas leakage and products of combustion are rapidly dispersed by wind and natural convection.

Any outdoor enclosure or alfresco area in which the appliance is used shall comply with one of the following:

An enclosure with walls on all sides, but at least one permanent opening at ground level and no overhead cover. See

Figure .

Within a partial enclosure that includes an overhead cover and no more than two walls. See Figure 2 & 3.

Within a partial enclosure that includes an overhead cover and more than two walls, the following shall apply:

- At least 25% of the total wall area is completely open; and

- At least 30% of the remaining wall area is open and unrestricted. See Figure 4 & 5.

In the case of balconies, at least 20% of the total of the side, back and front wall areas shall be and remain open and

unrestricted.

The following diagrams provide a diagrammatic representation of outdoor areas. Rectangular areas have been used in these

figures - the same principles apply to any other shaped area

Figure 1 - Enclosure with walls on all sides but Figure 2 - Partial Enclosure with overhead cover and

no overhead cover no more than two walls

Figure 3 - Partial Enclosure with overhead cover and Figure 4 - Open side at least 25% o total wall area.

no more than two walls 30 % or more in total o the remaining wall area is

open and unrestricted.

Figure 5 - Open side at least 25% o total wall area. 30 percent

or more

in total o the remaining wall area is open and

unrestricted

* Us spann r to tight n all gas fittings

* Ch ck all gas hos and lin conn ction for

damag , cuts or cracks ach tim for using

th applianc .

* Always l ak t st with soapy wat r

*Ch ck main burn rs, sid burn rs and

infrar d r ar burn r r gularly for spid r w bs

and ins ct n sts as th s may int rf r with

th prop r op ration of th burn rs and must

b r mov d b for using th burn rs.

* Us th applianc outdoors only

* Acc ssibl parts mayb v ry hot. Always

K p childr n away from th applianc

*Hav th gas cylind r fill d by an authoriz d

gas suppli r

* Always w ar prot ctiv glov s wh n

handling hot compon nt

* Clos th gas cylind r valv aft r ach us

* Cl an th gr as tray r gularly.

* USE grill at l ast 915mm from any

combustibl , wall or surfac .

* “Burning off” th barb cu aft r v ry us

(for approx 15 minut s) will k p xc ssiv

food r sidu to a minimum.

* Turn off th gas supply at th cylind r in th

v nt of gas l ak.

Do not do

* Do not l an ov r applianc wh n lighting

* Do not stor combustibl mat rials, gasolin ,

flammabl liquids or vapors within vicinity

of barb cu

* Do not us applianc with any cov r on

* Do not us plastic or glass ut nsils on th

Barb cu

* Do not us th applianc in strong winds

* Do not dismantl control valv s

* Do not t st for gas l aks with a nak d flam

* Do not stor spar gas cylind rs in th

cabin t

* Do not lay th gas cylind r down ( always

k p upright)

* Do not us applianc indoors

* Do not modify th construction of th

applianc or th siz of any burn r, inj ctor

orific or any oth r compon nts

* Do not mov th applianc during us

* Do not obstruct any v ntilation of th

applianc

* Do not allow th fl xibl gas supply hos or

any l ctrical cord to com in contact with any

h at d surfac of th applianc

* Do not us charcoal or any oth r solid fu l in

this applianc

* Do not disconn ct any gas fittings whil th

applianc is in us

* Do not us a rusty or d nt d gas cylind r

with a damag d gas valv

* Do not fill th gas cylind r b yond 80%

capacity

* Do not us th infrar d r ar burn r at th

sam tim as oth r burn rs

Gas Cylinder Information

Gas Cylind r Saf ty Information

• This applianc is d sign d to b us d with a gas cylind r not xc ding 9KG.

• Th gas cylind r supply valv must b turn d off wh n th applianc is not in us .

• Gas cylind rs must b stor d outdoors, out of r ach of childr n and must not b stor d in a building, garag or any

oth r nclos d ar a.

• Th gas cylind r us d must incorporat a saf ty collar to prot ct th valv ass mbly.

* N v r stor a spar cylind r und r th barb cu sh lv s or insid th troll y housing. Any

LPG cylind r not attach d to th BBQ for us should b stor d outdoors and w ll away from this applianc .

Important:

• Wh n disconn cting and r moving th gas cylind r for th purpos of r filling, always obs rv th following

proc dur .

• Ensur that all gas control valv s on th applianc and th gas cylind r ar turn d off b for disconn cting th

r gulator from th cylind r.

• Do not smok or us a nak d flam n ar th applianc or gas cylind r whil disconn cting th gas lin b tw n th

applianc and gas cylind r.

• R mov th gas cylind r from th nclosur b for disconn cting th r gulator from th applianc .

• Tight n all conn ctions b for placing th gas cylind r back in its nclosur .

• Th gas l ak t sting proc dur should b conduct d v ry tim th gas cylind r is r fill d and r conn ct d to th

applianc b for using th applianc .

R gulator Conn ction

1. Ch ck that all control knobs ar in th ‘Off’ position.

2. Mak sur th cylind r valv is off.

3. R mov th prot ctiv cap from th cylind r if pr s nt.

4. L ak t st th conn ction with a soapy wat r solution.

Gas L ak T st Proc dur

N v r us a nak d flam to ch ck for gas l aks. Always us th following proc dur to ch ck for gas l aks.

1. In a small contain r, mix up a solution of wat r and d t rg nt or soap. Mix th solution w ll.

2. Mak sur that th gas supply valv on th gas cylind r is turn d on.

3. Mak sur that th gas control valv s on th applianc ar all turn d off.

4. Using a brush or spray bottl apply th solution to th gas lin and ach join in th gas lin .

5. Bubbling of th solution will indicat that th r is a l ak pr s nt.

6. R -tight n or r -s al any joints that ar l aking.

7. If a l ak p rsists th n contact your distributor or th manufactur r for assistanc .

LIGHTING YOUR BARBECUE

This barb cu is d sign d for us outdoors, k p away from any flammabl mat rials.

It is important that th r ar no overhead obstructions and that th r is a minimum distanc of 915mm from th sid or

r ar of th applianc . Do not us th BBQ und r ov rh ad combustibl mat rials.

It is important that th v ntilation op nings of th cylind r compartm nt ar not obstruct d.

Th barb cu must b us d on a l v l, stabl , non-flammabl surfac .

Th applianc should b prot ct d from dir ct draughts and shall b position d or prot ct d against dir ct p n tration by

any trickling wat r ( .g. rain). Parts s al d by th manufactur r or his ag nt must not b alt r d by th us r.

No modifications should b mad to any part of this barb cu and r pairs and maint nanc should only b carri d out by

an authoriz d p rson.

DO NOT l t childr n op rat or play n ar grill.

DO NOT us charcoal or c ramic briqu ts in a gas grill

DO NOT light or us th sid burn r with th lid in th clos d position.

DO NOT att mpt to light burn r with lid clos d. A build-up of non-ignit d gas insid a clos d grill is hazardous

Th sid burn r is d sign d for pot/pan with diam t r 60-260mm. Sid burn r lid can not b

us d as work tabl , do not put anything on th sid burn r lid.

Lighting Instruction:

1. Read instructions before lighting.

2. Open the lid and make sure all the knobs are on the OFF( ) position.

Conn ct th r gulator to gas cylind r and th hos to barb cu .

Turn the gas supply ON” at the cylinder. Check with

the use of soapy water for any gas leakage between the bottle and the regulator.

Push down th control knob and k p pr ssing whilst turning anti-clockwis to HIGH ( ) position whilst also pr ssing

th ignition button (a clicking sound is h ard), this will light th burn r.

5. If th burn r still do s not light, turn th control knob to OFF

( )

wait 5 minut s and r p at st p 4. If th burn rs do

not stay alight , r p at st ps 4 and 5.

6. Adjust th h at by turning th knob to th High ( )/Low ( ) position.

7. To turn th barb cu ‘OFF’ turn th cylind r valv to th ‘OFF’ position and th n turn all

of th control knobs on th applianc clockwis to th OFF

( )

position.

For Infrared rear burner

Push down th control knob and k p pr ssing whilst turning anti-clockwis to HIGH ( ) position and also pr ssing th

ignition button (a clicking sound is h ard). Aft r th infrar d r ar burn r is lit, k p pushing down th control knob and hold

for 5 s conds. It may tak a littl whil for th gas to flow to th infrar d burn r b

ecause it is some distance away from

the gas valve.

For Match- Lighting:

1. Follow above instruction step 1-3.

2. For Main burn r, plac th match into match lighting stick

and light th match, th n put into lighting hol on right

sid of th barb cu ; For burn rs far away from right sid

of th barb cu , tak th cooking grat out and plac th

match n ar th main burn r ports;

For side burner, place the lit match on the holes of the

side burner head,

For infrared rear burner, place the lit match on the

surface of ceramic panels

3. Push down and turn the knob anticlockwise to HIGH( ) position. Thus the burner could be lit. If the burner does

not light, turn off the gas tap and wait for 5 minutes then repeat this step 2-3.

B for cooking for th first tim , op rat th barb cu for about 15 minut s with th lid clos d and th gas turn d on

HIGH(

)

. This will “h at cl an” th int rnal parts and dissipat odor from th paint d finish. Th color of cooking ar a

may slightly discolour. This is normal and it is th natur of mat rial.

While igniting main burner and infrared rear burner, please make sure the lid for main burner is in open position

While igniting side burner, please make sure the lid for side burner is in open position

Battery Replacement:

Unscrew the battery cap and plastic nut on the igniter

at the front of the control panel. Replace the battery

and refit the cap.

CLEANING AND CARE

All cl aning and maint nanc should b carri d out wh n th barb cu is cool and with th fu l supply turn d OFF at th

gas cylind r.

DO NOT mistak brown or black accumulation of gr as and smok for paint. Surfac s of th gas grills & hotplat s ar not

paint d. Apply a strong solution of d t rg nt and wat r or us a grill cl an r with scrubbing brush on insid s of

grill lid and bottom. Rins and allow to compl t ly air dry.

DO NOT apply a caustic grill / ov n cl an r to any paint d surfac s.

DO NOT us abrasiv or flammabl cl an rs, as it will damag th parts of th product and may start a fir .

Plastic parts: wash with warm soapy wat r and wip dry.

Porcelain surfaces: b caus of glass-lik composition, most r sidu can b wip d away with backing soda / wat r solution

or sp cially formulat d cl an r. Us nonabrasiv sourcing powd r for stubborn stains.

Painted surfaces: wash with mild d t rg nt or nonabrasiv cl an r and warm soapy wat r. Wip dry with a soft

nonabrasiv cloth.

Stainless steel surfaces: Stainl ss st l will surfac rust if not maintain d w ll. To maintain your grill’s high quality

app aranc , wash with mild d t rg nt and warm soapy wat r and wip dry with a soft nonabrasiv cloth aft r ach us .

Us stainl ss st l prot ction liquid lik WD-40 on th surfac to avoid rust.

Coo ing grid:

Use a mild soapy water solution. Non-abrasive scourer can be used on stubborn stains then rinse with

water.

Abnormal Operation:

Any of th following ar consid r d to b abnormal op ration and may r quir s rvic

Y llow tipping of th y llow flam

Sooting up of grills plat s

Burn rs not igniting prop rly

Burn rs failing to r main alight

Burn r xtinguish d by troll y doors

Gas valv s, which ar difficult to turn

Technical Information

Mod l No.: EA120BTSX/

CB6-SBG001-BU

EA120BIS/

CB6-BG001(B)

T st Point Pr ssur : 2.75KPA 2.75KPA

Total Nominal

Gas Consumption:

96.1 MJ/h

81.1 MJ/h

Gas Typ : Propan Propan

Nominal gas consumption:

Main Burn rs: 11.6 MJ/h x 6

Sid Burn r: 15MJ/h

Back Burn r: 11.5MJ/h

Main Burn rs: 11.6 MJ/h x 6

Back Burn r: 11.5MJ/h

Inj ctor Siz :

Main Burn rs: 0.98mm

Sid Burn r: 1.13mm

Back Burn r: 1.00mm

Main Burn rs: 0.98mm

Back Burn r: 1.00mm

Mod l No.: EA90BTSX/

CB4-SBG001-BU

EA90BIS/

CB4-BG001(B)

T st Point Pr ssur : 2.75KPA 2.75KPA

Total Nominal

Gas Consumption:

72.9 MJ/h

57.9MJ/h

Gas Typ : Propan Propan

Nominal gas consumption:

Main Burn rs: 11.6 MJ/h x 4

Sid Burn r: 15MJ/h

Back Burn r: 11.5MJ/h

Main Burn rs: 11.6 MJ/h x 4

Back Burn r: 11.5MJ/h

Inj ctor Siz :

Main Burn rs: 0.98mm

Sid Burn r: 1.13mm

Back Burn r: 1.00mm

Main Burn rs: 0.98mm

Back Burn r: 1.00mm

AGA Approval No.: AGA 7142 G

For Us outdoors and in w ll v ntilat d ar as

Warning: Acc ssibl parts may b v ry hot, k p young childr n away.

Clos th valv of th gas cylind r or th r gulator aft r us .

Th us of this applianc in nclos d ar as can b dang rous and is prohibit d

For storag and cylind r xchang , disconn ct th cylind r only. Do not disconn ct hos from th

applianc .

Always maintain 915mm minimum cl aranc to combustibl mat rials at th r ar and sid s of

th BBQ. Do not us this BBQ und r ov rh ad combustibl surfac s.

Conv rsion to natural gas only to b don by authoriz d p rson.

The minimum cylinder size for use with this appliance is 7kgs

The thread type of this appliance is G1/4B.

Exploded View

Model No. : EA120BTSX

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Parrilla de otras marcas

Orbegozo

Orbegozo GR 2300 Manual de usuario

bora

bora PT11 Manual de usuario

Klarstein

Klarstein 10031664 Manual de usuario

Garland

Garland MWE3W Manual de usuario

Char-Broil

Char-Broil 463722714 Manual de usuario

Nexgrill

Nexgrill 720-0830HK Manual de usuario

Kenmore

Kenmore 415.16123800 Manual de usuario

Camp Chef

Camp Chef PG24CLAU Manual de usuario

Tucker Barbecues

Tucker Barbecues GTR Series Instrucciones de montaje

Monogram

Monogram ZGG540NCP1SS Manual de usuario

Equipex

Equipex Sodir Savoy Manual de usuario

Gaggenau

Gaggenau VR 414 610 Manual de usuario

Miele

Miele KM 408-1 Manual de usuario

George Foreman

George Foreman GGR50B Manual de usuario

AOG

AOG T series Manual de usuario

Gorenje

Gorenje TG2000CB Manual de instrucciones

Weber

Weber Genesis Silver-B Permamount NG 051701 Manual de usuario

Glen

Glen SA 3037 Manual de usuario