EURA ELH-20H4 Manual de usuario

ELECTRONIC HANDLE

WITH ACCESS CONTROL

User manual

ELH-20H4

CARD

CONTENTS

1. GENERAL CHARACTERISTICS AND INTENDED USE.........................................................................4

2. SET CONTENTS .....................................................................................................................................4

3. STRUCTURE...........................................................................................................................................5

4. OPERATION PRINCIPLE.......................................................................................................................6

5. MOUNTING THE ELECTRONIC HANDLE IN THE DOOR ...................................................................6

5.1. SETTING HANDLE ORIENTATION (LEFT/RIGHT DOORS) ..........................................................8

5.1.1 SETTING ORIENTATION - HANDLE FRONT........................................................................8

5.1.2 SETTING ORIENTATION - BACK OFESCUTCHEON...........................................................8

5.2. INSTALLING THE BOLT INTHE ELECTRONIC HANDLE..............................................................9

5.3. BATTERY INSTALLATION ..............................................................................................................9

5.4. INSTALLATION DIAGRAM...........................................................................................................10

5.5. EMERGENCY ENTRANCE............................................................................................................ 12

6. RESETTHE HANDLE .......................................................................................................................... 13

7. PROGRAMMING AND OPERATION OFTHE ELECTRONIC HANDLE WITHACCESS CONTROL.. 13

8. TECHNICAL SPECIFICATION ..............................................................................................................14

INITIAL NOTES

Please read these operating instructions carefully before installing, connecting and using the

unit. In the case of any problems with understanding the content of this document, please

contact the device seller.

Installation and start-up of the device by the user are possible if adequate tools are used. Ne-

vertheless, it is recommended to have the device installed by qualied personnel.

Because of the possible damage to the handle with access control:

-the device should never be installed in doors with a door closer,

-the door in which the device is going to be installed should be correctly installed and adju-

sted along the door frame,

-the door leaf must close easily (without springing) and the maximum operating forces ac-

ting on the device should exceed the threshold values specied in the device specication

provided in this manual,

Handles with access control should not be installed in saunas, refrigerated warehouses and

other premises, where relative humidity and ambient temperature exceed the threshold valu-

es indicated in the technical specication of the device.

For added security, it is recommended to install the patented insert, which also acts as an

additional emergency entry option.

The manufacturer shall not be liable for damage which may occur as a result of incorrect instal-

lation or operation, as well as unauthorised repairs and modications.

Remember to:

-use the device according to its intended use, keep it away from moisture and re, do not

throw into re, avoid impacts, do not crush and expose the device to mechanical damage,

-do not clean the device with water, solvents or other chemicals,

- clean the housing only with the power supply cut o, use only a wet cloth for cleaning and

wait until the housing is completely dry aer cleaning,

- do not carry out unauthorised modications or repairs,

Caution!

Devices with a protection degree equal to or higher than IP44 may be installed outdoors

(e.g. doorbell buttons, outdoor video intercom panels, cameras, etc.). Information about the

protection degree is available in the technical specication of the device.

1. GENERAL CHARACTERISTICS AND INTENDED USE

An electronic handle with access control simply limits access to protected areas for unauthori-

zed persons. It is designed for both le and right doors, and the universal spacing of mounting

screws allows for the use of an already installed mortise lock in most cases.

The handle body features a proximity key reader (Mifare 13.56 MHz) and a touch numeric key-

pad with Bluetooth module. Additionally, a ngerprint reader is installed above the numeric

keypad.

Aer approaching the key fob to the reader, entering the correct PIN code, using a mobile

application, or placing a nger on the ngerprint reader, the lock inside the handle is released.

2. SET CONTENTS

handle with an integrated

battery compartment 2 anti-slip

pads

2 keys for manual door

opening in case

of emergency

additional

pin locking

bolt

4 screws

for mounting

sleeves

2 pins

* Note

The relevant accessories - pin, sleeves and tie bolts should be selected according to the door leaf thickness.

pin locking

split pin

2 mounting

sleeves

Manual

electronic handle

with an access control module

2 bolts for

the locking sleeve

2 locking

sleeves

assembly

template

CARD

Fig. 1.

3. STRUCTURE

Touch-sensitive keypad

with key fob reader

Fingerprint reader

Inner side External side

CARD

Battery

compartment cover

Fig. 2. Budowa

127 mm

43 mm 40 mm

300 mm

45 mm

71 mm

58 mm 88 mm 154 mm

24 mm

13 mm

CARD

Fig. 3. Dimensions

4. OPERATION PRINCIPLE

Aer receiving a signal from the electronic access control module, the servo motor unlocks

the mechanical gearbox, allowing the door to be opened by normal operation of the external

handle. The opening is indicated by a sound. The waiting period for handle operation is facto-

ry-set to approximately 5 seconds, aer which the gearbox is re-locked and the lock returns to

standby mode, waiting for the next signal from the electronic access control module.

From the inside of the room, the door can always be opened by simply pressing the handle.

Once the door is closed, the latch mechanism immediately engages, preventing the door from

being opened from the outside without a signal from the electronic access control module.

There is an emergency lock release feature that can be activated using a mechanical key, of

which two copies are included in the kit. Additionally, the device has an access block function,

which allows entry to the room only through the administrator application or emergency en-

try key.

5. MOUNTING THE ELECTRONIC HANDLE IN THE DOOR

The kit includes pins, sleeves, and screws for mounting the handle in doors with a thickness

of 35-65 mm. During installation, the appropriate length of the supplied components must be

selected.

Note!

Installation should be carried out with emergency keys on hand, which may be necessary if

the door is accidentally locked with an unprogrammed lock. The lock should be installed on

the open door leaf, and aer installation and programming of the lock, a test of the device's

operation should be carried out, also on the open door leaf.

Example of locks installed in standard doors:

50 lub 55 mm

72 mm

50 lub 55 mm

90 mm

50 lub 55 mm

92 mm

Fig. 4.

Example of locks installed in doors with aluminum prole:

30 lub 35 mm

72 mm

30 lub 35 mm

90 mm

30 lub 35 mm

92 mm

Fig. 5.

5.1. SETTING HANDLE ORIENTATION (LEFT/RIGHT DOORS)

All electronic handles are universal and can be mounted on both le and right opening doors.

5.1.1 SETTING ORIENTATION - HANDLE FRONT

To determine the direction of the handle with built-in access control, loosen the

mounting screw located on the inner side of the escutcheon (Fig. 6.), then change

the direction of its position and tighten it again with the mounting screw.

Fig. 6.

5.1.2 SETTING ORIENTATION - BACK OF ESCUTCHEON

To set the direction of the handle with a built-in battery pocket, loosen the mounting screw

located on the inner side of the escutcheon (Fig. 7.), then change the direction of its position

and tighten it again with the mounting screw.

Fig. 7

5.2. INSTALLING THE BOLT IN THE ELECTRONIC HANDLE

The bolt should be placed in the slot located in the device body marked with a triangle, and

then the counter-locking washer included in the accessory kit should be installed.

Note:

When installing the bolt, remember to ensure that the slot in the

lock body is facing towards the handle.

Fig. 8.

PREPARATION OF A REPLACEMENT BOLT

If you wish to use a dierent bolt than the one included in the set, you should:

acquire a bolt with dimensions of 8 x 8 mm, then measure the appropriate length and cut the

bolt.

Note: The bolt must be cut to the correct length in order to eliminate the possibility of this

element sliding during use. Otherwise, the bolt slot will be at risk of damage.

5.3 BATTERY INSTALLATION

To install the battery in the battery compartment, slide the battery compartment cover

upwards.

Fig. 9

Attention!

-The device requires the use of alkaline batteries to function properly. Rechargeable bat-

teries should not be used.

-It is recommended to install and program the handle with the door open. Once the proper

operation is veried, the door can be closed.

-Aer inserting the batteries for the rst time, the handle automatically enters the armed

state. Therefore, batteries should only be inserted aer the electronic handle has been

mounted in the door. If the batteries were inserted earlier to open the door, the emer-

gency key should be used, which is recommended to be kept on hand during installation.

The electromechanical handle is powered by 4 alkaline DC 1.5 V AA batteries and can work for

approximately 1 year on one set of batteries. The battery status can be checked periodically

through the application aer synchronizing with the handle (via Bluetooth) or in real-time (by

using WiFi gateways in the system).

5.4. INSTALLATION DIAGRAM

To install the electronic handle in a door:

Fig. 10.

Existing mounting holes can be used, or new ones can

be prepared according to the template included in the

kit. To avoid damaging the mortise lock, it should be

removed and veried that it complies with one of the

standard samples shown in Fig. 4 or Fig. 5.

ATTENTION! It is also possible to install the han-

dle in a dierent standard aer verifying that instal-

lation in such a lock will not damage the lock or the

electronic handle. Additionally, the cylinder insert

should be removed from the lock. In most cases, the

hole le aer removing the cylinder insert will serve

as the mounting track for the lower handle sleeve.

The installation sequence for the electronic han-

dle is as follows:

Fig. 11.

1. According to Fig. 11, install the rubber washer and

screw the mounting sleeves (two types of sleeves

are included and should be selected according to the

door thickness) onto the front body of the handle.

2. Install the spindle into the handle socket and lock it

with the plug (two types of spindles are included and

should be selected according to the door thickness).

ATTENTION!

When mounting the plug in the spindle, ensure that

the triangle symbol on the spindle socket is facing to-

wards the handle grip. Aer placing the plug, adjust it

to t into the previously prepared spindle socket hole.

Otros manuales para ELH-20H4

Tabla de contenidos

Otros manuales de Cerradura de puerta de EURA

EURA

EURA ELH-62B9 SILVER Manual de usuario

EURA

EURA ELH-20H4 Manual de usuario

EURA

EURA ELH-60B9 SILVER Manual de usuario

EURA

EURA AC-01C9 Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

Assa Abloy

Assa Abloy effeff 827A-IP Manual de usuario

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario