eufy Security T8214 Manual de usuario
QUICK START GUIDE
Video Doorbell E340
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security
Logo are trademarks of Anker Innovations Limited, registered in the United
States and other countries. All other trademarks are the property of their
respective owners.
Model：T8214
51005004091 V01
01
AT A GLANCE
Front View
⑥
⑤
⑦⑧
①
②
③
④
⑨
①LED Light
②Motion Sensor
③Primary Camera Lens
④Microphone
⑤Ambient Light Sensor
⑥LED Ring / Doorbell Button
⑦LED Light
⑧Secondary Camera Lens
⑨Speaker
0302
Rear View
⑤
①
②
③
④
SYNC
①Detaching Mechanism
②Power Terminals for Existing Doorbell
Wires (Optional)
③SYNC Button
Press to turn on the doorbell.
Press and hold for 2 seconds until you hear a beep to
set up the doorbell. (Optional)
Press quickly 5 times within 3 seconds to turn off the
doorbell.
④Battery Compartment
⑤QR Code (Scan to add the doorbell in the app)
HOW THE SYSTEM WORKS
Works Independently
This video doorbell can work independently once it is
connected to your home wireless router. Additionally, you
have a variety of options to receive notifications and hear a
ring when someone presses your video doorbell.
• Use a traditional doorbell chime (if you have one).
• Use a eufy Security doorbell chime (sold separately).
• Use an Amazon Alexa Echo Show device.
Works with eufy Security HomeBase
(Optional)
The video doorbell detects motion at your porch and lets
you to answer the door anytime, anywhere. You can store
video clips in the built-in storage of your eufy Security
HomeBase 2 or S380 HomeBase (sold separately). When
someone rings the doorbell, people in the house will be
notified.
HomeBase
0504
CHARGING THE BATTERY
PACK
1. Remove the pre-installed battery pack from the battery
compartment.
0～100%
2. Fully charge the rechargeable battery pack before
installation.
3. Place the battery pack into the battery compartment.
0～100%
SETTING UP THE SYSTEM
1. Download and install the eufy Security app, then sign in
or create an account.
2. Follow the in-app instructions to add the video doorbell.
0706
DETERMING THE POWER
OPTION
Option 1: Battery Powered
If you don't have existing doorbell wiring at your front door,
use the included battery. You are free to determine the
location of the doorbell, and the mounting will be easy and
quick.
When the battery is low, you will need to recharge it. Battery
life varies with use. If you choose this option, please skip to
DOORBELL MOUNTING (Battery Powered).
Option 2: Wire Powered
If you have existing and working doorbell wires at your
front door, the video doorbell will be constantly powered
by these wires. So there's no need to detach and recharge
after installation.
The mounting position is limited. If you choose this option,
please skip to DOORBELL MOUNTING (Wire Powered).
DOORBELL MOUNTING
(Battery Powered)
Choose a Location
1. Take the video doorbell to your front door and check the
live view in the app. Choose a location where you can see
the desired field of view. Consider the following factors:
• Check if you can reuse the existing holes and anchors in
the wall or door frame.
• If you want to place the doorbell near a side wall, make
sure the wall isn't in the field of view. Otherwise, the IR
light will be reflected and the night vision will be blurred.
• If you are drilling the mounting holes for the first time, the
recommended height is 48" (1.2m) above the ground.
• To adjust the angle, use the 15º mounting wedge as a
supplementary mounting bracket.
15°
1.76m(5’9”)
1.2m (48")
0.3m
(12")
1m
(40")
0908
Mount the Bracket
Use the provided screws to secure the mounting bracket on
the wall.
Without 15º
Mounting Wedge
Mounting
Bracket
Mounting
Bracket
Wooden Wall
Mounting
Bracket
Mounting
Bracket
Mounting
Wedge
Mounting
Wedge
With 15°
Mounting Wedge
Hard Wall
Without 15º
Mounting Wedge
With 15°
Mounting Wedge
15°
1.76m(5’9”)
1.2m (48")
0.3m
(12")
1m
(40")
2. Place the screw hole positioning card against the wall
to mark the location. If mounting on a hard wall (brick,
concrete, or stucco), use a 15/64" (5.95mm) drill bit to drill 2
holes through the screw hole positioning card.
What you need: Phillips-Head Screwdriver; Power Drill
(15/64" Drill Bit)
1110
Install the Doorbell
Align the doorbell with the bottom of the mounting bracket,
then press the top of the doorbell into place until it clicks.
Recharging the Battery
1. Insert the detaching pin into the pin hole on the top of
the doorbell, then lift the top for removal.
2. Repeat steps in "CHARGING THE BATTERY PACK".
You can purchase an extra battery pack for quick replacement.
DOORBELL MOUNTING
(Wire Powered)
Check the Doorbell Wires
1. Ring the existing doorbell to check if it is working. If
it doesn't ring, your doorbell wires may be defective.
Power on the doorbell by the built-in battery or consult an
electrician to repair the wires.
2. Shut off the power at the circuit breaker. Turn the lights
on and off to make sure the electricity in your home is
properly shut off.
OFF
OFF
Always be careful when handling wires. If you're not comfortable
installing it yourself, have a qualified electrician to do it.
1312
Detach the Existing Doorbell Button
If you already have existing doorbell wiring:
1. Remove the existing doorbell button with a Phillips-head
screwdriver (not provided).
2. Pull the two wires out carefully when removing the
existing doorbell. Straighten the wire ends if necessary.
Choose a Location
1. Take the video doorbell to your front door and check the
live view in the app. Choose a location where you can see
the desired field of view. Consider the following factors:
• Check if you can reuse the existing holes and anchors in
the wall or door frame.
• If you want to place the doorbell near a side wall, make
sure the wall isn't in the field of view. Otherwise, the IR
light will be reflected and the night vision will be blurred.
• If you are drilling the mounting holes for the first time, the
recommended height is 48" (1.2m) above the ground.
• To adjust the angle, use the 15º mounting wedge as a
supplementary mounting bracket.
1.76m(5’9”)
1.2m (48")
0.3m
(12")
1m
(40")
1514
Mount the Bracket
Use the provided screws to secure the mounting bracket on
the wall.
Without 15º
Mounting Wedge
Mounting
Bracket
Mounting
Bracket
Wooden Wall
Mounting
Bracket
Mounting
Bracket
Mounting
Wedge
Mounting
Wedge
With 15°
Mounting Wedge
Hard Wall
Without 15º
Mounting Wedge
With 15°
Mounting Wedge
15°
1.76m(5’9”)
1.2m (48")
0.3m
(12")
1m
(40")
2. Place the screw hole positioning card against the wall
to mark the location. If mounting on a hard wall (brick,
concrete, or stucco), use a 15/64" (5.95mm) drill bit to drill 2
holes through the screw hole positioning card.
What you need: Phillips-Head Screwdriver; Power Drill
(15/64" Drill Bit)
1716
Connect the Wires to the Doorbell
Connect the wires to the terminals on the back of the
doorbell, then tighten the terminal screws. Wire can be
connected to any terminal.
SYNC
SYNC
To prevent short-circuiting, make sure the wires are not
touching each other after connecting them to the terminals.
If the wires are too short, use the extension wires and wire
nuts to make them longer. Use electrical wiring tape instead
if there is no more space on the wall for wire nuts.
Install the Doorbell
Align the doorbell with the bottom of the mounting bracket,
then press the top of the doorbell into place until it clicks.
Restore Power
Switch the main circuit breaker back to ON. You're all set!
OFF
OFF
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de eufy Security
