ETL SecureLogic Series Manual de usuario
1.ai 2/14/2005 9:43:32 AM
Congratulations and thank you for
purchasing the ETL®SecureLogic™ Wall
Vault™. Your new Wall Vault™ is a high
quality security product, that can be used
to store a variety of items out of reach of
children or other unauthorized persons.
Please read through the following
instruction guide carefully before installing
your Wall Vault™.
1. Wall Vault™
2. Battery Charger
3. Mounting Bolts (4)
4. Washers (4)
5. Allen Wrench
6. Keys (2)
7. Installation Guide
8. Quick Reference Card/Template
9. Warranty Card
PACKAGE CONTENTS
1
2.ai 2/14/2005 11:03:49 AM
TABLE OF CONTENTS
Warnings & Recommendations pg. 3
Standard Features pg. 5
Installation Instructions pg. 7
Programming Model 20700 pg. 9
Programming Model 20710 pg. 12
Operating Instructions pg. 13
Maintenance Instructions pg. 15
Security Features pg. 16
Trouble Shooting pg. 17
Warranty & Registration pg. 18
2
3.ai 2/14/2005 11:06:34 AM
WARNINGS AND RECOMMENDATIONS
Anything in this installation guide that has been written in Italics is a WARNING. Failure to
observe these instructions constitutes a MISUSE of this product and may result in serious
physical injury or DEATH.
NO UNAUTHORIZED REPAIR
The Wall Vault™ is serviceable at the factory only. Any tampering, unauthorized repair
and/or modification will void all warranties, and may cause the safe to fail unexpectedly,
or be damaged. If in doubt, call Customer Service at 1-209-529-3546.
FIREARM SAFETY
WARNING: The Wall Vault™ or any other firearm storage device cannot take the place
of other safety procedures including advising children of the dangers of firearms.
WARNING: The manufacturer and distributors of the SecureLogic™ Wall Vault™ do
not recommend, suggest, advise, promote or otherwise condone the ownership of
firearms.
RECOMMENDATION: The touchpad and biometric sensor on the control panel are
electronic. They have a certain feel to them and may seem different to different people. It
is important that you become accustomed, through practice, as to how the Wall Vault™
responds to your personal touch.
3
!
!
!
4.ai 2/14/2005 11:11:04 AM
!
!
WARNING: Never grab your firearm by the trigger when removing or placing into the
Wall Vault™. Make sure your firearm’s safety mechanism is on.
WARNING: Always follow the firearm safety rules set out by the firearm’s
manufacturer.
IMPORTANT NOTICE:
- Vault must be in vertical position and installed on a vertical wall in order for door
to drop open
- Door must be open in order to install
- Designed to install between 16” studs on center
- Recommended installation height is approximately 5 feet from the floor. The Wall
Vault™ must be clear from obstruction 10” below
- Once installed, allow battery to charge for 12 hours
RECOMMENDATION: Before installing Wall Vault™ consult a licensed contractor to ensure
safety and proper installation.
4
5.ai 2/14/2005 11:15:18 AM
STANDARD FEATURES
1. Drop down quick access door >
2. 12 gauge stainless steel face >
3. Plush fabric interior >
4. Touchpad / Numeric Keypad >
5. Biometric Finger Sensor with 6 user storage >
(Model 20700 Only)
6. Emergency access key lock with 2 keys >
7. Hidden storage compartment >
8. Interior light >
5
6.ai 2/14/2005 11:21:38 AM
1.
6.
7.
2.
3.
4.
5.
6
7.ai 2/14/2005 11:23:41 AM
INSTALLATION INSTRUCTIONS
The Wall Vault™ is specifically designed to be mounted into a standard residential wall with at least 2x4
construction and wall studs of at least sixteen (16) inches on center apart. It is recommended to use an
industrial grade stud finder to locate studs and ensure the wall void is free of other obstructions (ie. water
pipes, electrical conduit, etc.).
Installing the Wall Vault™ (Please Review Warnings & Recommendations Section)
1. Locate desired mounting location (please refer to IMPORTANT NOTICE section on pg. 4) (See Figure 1)
2. The insertable section of the Wall Vault™ is approximately 14” x 14”. It is recommended to allow a 1/8“
tolerance for each side of the Wall Vault™ making the hole size approximately 14.25” x 14.25“. Once
mounting location is determined, cut hole in wall accordingly. (Refer To Template) (See Figure 2)
3. Carefully place vault in wall. Do not forcefully insert. Vault should slide into wall easily (See Figure 3)
4. Open vault door
A. Biometric Wall Vault™ (Model 20700)
a. Press the ‘*’ button located on the Touchpad (See Figure 4A)
b. Wait five (5) seconds until beep, green LED light will flash once
c. Press default code, 1 2 3 4 4 and ‘*’ button
* If the battery is dead, use emergency access key (refer to Operating Instructions)
B. Keypad Wall Vault™ (Model 20710)
a. Input pin (default is 1 2 3 4) and press ‘#’ (See Figure 4B)
* If the battery is dead, use emergency access key (refer to Operating Instructions)
5. Vault door will drop (See Figure 5)
6. Locate the 4 mounting tabs, 2 on each side of vault walls (See Figure 6)
7. Mark holes for pre-drilling (See Figure 7)
8. Remove vault and pre-drill holes with a 1/8” bit
9. Reinsert vault and screw bolts and washers into pre-drilled holes through vault tabs (See Figure 8)
Biometric Wall Vault™ Trickle Charge Option: (Model 20700) See Important Note Below
Please consult a licensed electrician for questions.
Important: Terminal only accepts 12-14 VDC. DO NOT WIRE DIRECTLY TO TYPICAL HOUSE WIRING 110 VAC
1. Locate terminal jack beneath sticker at top side of vault
2. Wire to terminal a 12-14 VDC
3. Terminal will accept non-specific polarity
7
8.ai 2/14/2005 11:28:37 AM
AH
BCD
IJK OPQ RST
UVW
LMN
XYZ
*#
EFG
13
24
5678
90
5 feet
Template
123
4A 4B
678
5
8
9.ai 2/14/2005 11:32:32 AM
PROGRAMMING INSTRUCTIONS (MODEL 20700)
TouchPad
The numbered touchpad operates on the capacitance of your skin and is very accurate in sensing the
pressure of a touched area. Very little pressure is needed to operate this sensor. However, when using the
numbered touchpad, the entire area of the number should be covered with your finger. This will ensure an
accurate number is input every time it is used.
Biometric Sensor
The fingerprint sensor maps your specific fingerprint using capacitance technology and computer
algorithms. This technology is very accurate when a “good” fingerprint is captured, and is not easily fooled
by counterfeits. In order to capture a “good” fingerprint, adequate pressure should be applied when first
enrolling a new fingerprint, i.e. enough pressure should be applied so that the entire face of your finger is
flat on the sensor. This will ensure that the sensor captures a good fingerprint and reduces the chance of an
enrolled fingerprint being denied access.
Setting Administrator Pin and Fingerprint
Once you are ready to program your Wall Vault™, the Administrator will need to be chosen. The
Administrator should be the primary user of the vault. The Administrator will be the only one allowed to add,
delete, or modify users. For security purposes, there can only be one Administrator.
1. Press ‘*’ button and wait for five (5) seconds.
2. Press ‘1’ and hold for three (3) seconds. One (1) beep, followed by three (3) beeps will indicate the
system is in Admin Mode.
3. Enter current pin number (default is 1 2 3 4 4) and press the ‘*’ button
4. Enter new pin number (must be 5 digits in length and can not include ‘*’ button as part
of pin) and press the ‘*’ button
5. Re-enter pin number followed by the ‘*’ button. Green light will flash.
6. With green light flashing, immediately place finger on biometric sensor. Center and place finger
parallel with biometric sensor pad. Once finger is recorded, beep will sound. The Administrator
fingerprint is now recorded. This fingerprint will be required to add new users.
7. Biometric sensor will store one (1) Administrator fingerprint and five (5) additional user prints.
8. If at any point during Programming you see a Red light, repeat steps 1-6.
9
10.ai 2/14/2005 11:34:07 AM
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Manuales populares de Seguro de otras marcas
Honeywell
Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Manual de usuario
Hornady
Hornady SnapSafe Trunk Safe II Manual de usuario
SPORTS AFIELD
SPORTS AFIELD SA-HD5-BIO Manual de usuario
Honeywell
Honeywell 5912 Manual de usuario
Phoenix
Phoenix FS1280F Manual de usuario
Phoenix
Phoenix SS0992K Hoja de información del producto
Technomax
Technomax Trony Series Manual
SPORTS AFIELD
SPORTS AFIELD INSTINCT BIOMETRIC Series Manual de usuario
RICHTER CZECH
RICHTER CZECH LA Manual de operación
Olymp
Olymp GOsafe 110 Manual de usuario
Phoenix
Phoenix SS0100E Hoja de información del producto
Clarke
Clarke Strong-Arm CS1000K Manual de instrucciones