eTIGER ES-DLS-01 Manual de usuario
ES-DLS-01
Wireless Security DockLock Base Set
www.etiger.com
ON
OFF
ON
OFF
Smart Access Door Lock set inter gate the Wireless technology, compatible with Etiger Home
secure Alarm Set S5/S6/secure Box V2/ secure Bub/ secure Hub Heating.The Main lock is fixed
inside of door, it is highly protected to be destroyed by thief from outside.Thief can not Use
kind of Electric drill to touch the lock.
This is a wireless smart lock kit for home use. It consists of a Wireless Lock and two Remote
Transmitters. Super strong 3M stickers provide a simple way for installation, no door destroy, no
hole,wireless,no power cab. 433Mhz Rolling Code of encryption algorithm and the split design
guarantee higher-secure.
The Keypad can store 500 PIN/card users. Because of ultra low power consumption, the Keypad
and Remote Transmitters can work as long as one year (bases on 30 times /day), Wireless Lock
can work 6 months. It will remind people to replace batteries intelligently if low battery.
- 500 PIN/card users
- 4-8 digits PIN, 13.56M Hz M1 Card
- With two Remote Transmitters
- 433MHz Rolling Code technology
- Communication distance: 50m Max
- Ultra low power consumption
FEATURES
INTRODUCTION
User Capacity
PIN Length
Card Type
Operating Voltage
Wireless Lock
Remote Transmitter
Idle Current
Working Current
Wireless Lock
Remote Transmitter
Communication Frequency
Communication Distance
Operating Temperature
Wireless Keypad
Wireless Lock
Operating Humidity
Physical
Wireless Lock
Remote Transmitter
Dimensions
Wireless Lock
Remote Transmitter
Unit Weight
Wireless Lock
Remote Transmitter
500
4-8 Digits
13.56M Hz M1 Card
2 units of AA batteries
1 unit of 2032 Lithium battery
All items ≤10uA
≤42mA
≤3mA
433MHz
50m Maximum
-40°C～+60°C(-40°F～+140°F)
-20°C～+60°C(-4°F～+140°F)
0%～86%RH
Zinc-Alloy + ABS Shell
ABS Shell
L150*W95*D39(mm)
L55*W32*D10(mm)
800g
16g/pc
SPECIFICATIONS
Major Parts
ON
OFF
ON
OFF
The device packed with 3M double-side stickers, can easily stick the Wireless Keypad and
Wireless Lock on smooth surface (We used high-quality 3M stickers, the stickiness will be the
best after sticking in 24 hours).
Below introduction for how to installWireless Lock intensively:
Method 1: Stick by 3M stickers
Confirm the direction and position of Hasp, meanwhile, make sure the Hasp align the
doorframe.
(So please make sure the direction of Hasp is fit for main body of lock before installation.)
Attentions of installing the Hasp
Put the Locating Rings into Hasp, and stick the 3M sticker at the back side of Hasp (You can
screw the hasp on the Reinforcing Plate if needed, then stick 3M sticker at the back of plate. It
can increase the stick area to make the Hasp stronger).
Installing the Hasp
Fix the main body of lock and the Fixed Plate by M5*6 hex screws in the packaging, and stick the
3M sticker on the back of Fixed Plate.
Installing the main body of lock
OPEN
CLOSE
INTRODUCTION
Press the Mechanical Switch on the main body of lock to open the lock mechanically, and
match the Hasp. Make sure it can be combined with Hasp perfectly, then stick the mail body of
lock on the door.
Combining the lock
Note: Mechanical Switch, it is used for installation and equipment trouble, please don’t
press it often in the normal condition.
When press the Mechanical Switch, the lock will be unlock all the time until open the
door one time by valid card, or valid PIN, or touch the close icon on the lock, or unlock
button on Remote Transmitter.
Method 2: Install by screws
OPEN
CLOSE
OPEN
CLOSE
87mm
61mm
Simplified Instruction
Function description
Enter the Program Mode:
Change the Master Code:
IMPORTANT NOTE: Please remember
the New Master Code as it can’t be reset
to default if forgotten
Add PIN User:
Add Card User:
Add fingerprint User:
Delete User:
Exit from the Program Mode:
How to release the door
PIN Access:
Card Access:
By Remote Transmitter:
By Wireless Lock:
Lock Immediately
By Keypad:
By Remote Transmitter:
By Wireless Lock:
Fingerprint Access:
Enter and Exit Program Mode
Operation
*(123456)#
(123456 is the factory default master code)
0 (New Code) # (Repeat New Code) #
(code: 6 digits)
1 (User ID) # (PIN) #(Repeat PIN) #
1 (Read Card)
1 (User ID) #（Read fingerprint）
#(Repeat Read fingerprint) #
2 (User ID) #
2 (Read Card)
*
PIN #
(Read Card)
Press
Touch
Press“0#”
Press
Touch
(Read Fingerprint)
Programming Step Keystroke Combination
1. Enter Program Mode
2. Exit
* (Master Code) #
(Factory default is 123456)
*
OPEN
CLOSE
PROGRAMMING
Set Master Code
Programming Step Keystroke Combination
1. Enter Program Mode
2. Update Master Code
3. Exit
Please do remember your Master Code because the Master Code can’t be reset if forget it.
* (Master Code) #
0（New Master Code）#
（Repeat New Master Code）#
Master code is any 6 digits
*
Add Users PIN(s)
Programming Step Keystroke Combination
1. Enter Program Mode
2. Add PIN
3. Exit
User ID: 0~499
PIN length: 4~8 digits
* (Master Code) #
1 (User ID) # (PIN) # (Repeat PIN) #
The users can be added continuously
*
Add Users Card(s)
Programming Step Keystroke Combination
1. Enter Program Mode:
2. Add Card:
Using Auto ID(Allows to assign Card
tonext available User ID number)
OR
2. Add Card:
Select Specific ID(Allows Master to
define a Specific User ID to associate
the card)
3. Exit:
User ID: 0~499
Card type: 13.56MHz M1 Card
* (Master Code) #
1 (Read Card) #
The cards can be added continuously.
1(User ID) # (Read Card) #
*
Change PIN
Programming Step Keystroke Combination
1.Change PIN:
By Card(There will be auto allocate
PIN (8888) to cards when adding)
OR
Change PIN: By User ID
2. Exit:
Note: Below is done outside programming mode, users can undertake this themselves
* (Read Card) (Old PIN) # (New PIN) #
(Repeat New PIN) #
* (User ID) # (Old PIN) # (New PIN) #
(Repeat New PIN) #
Exit automatically
Tabla de contenidos
