General Information & Cleaning: Installation:
READ THIS FIRST:
Check the pack and make sure you have all of
the parts listed on the front of this booklet. If
not, contact the outlet where you bought this
product.
This product must be installed by a
competent person in accordance with the
current building and IEE wiring regulations.
As the buyer, installer and/or user of this product
it is your own responsibility to ensure that this
fitting is fit for the purpose for which you have
intended it. Eterna Lighting cannot accept any
liability for loss, damage or premature failure
resulting from inappropriate use.
If in any doubt, consult a qualified electrician.
This product is designed and constructed
according to the principles of the appropriate
British Standard and is intended for normal
domestic service. Using this fitting in any other
environments may result in a shortened working
life, for example where there is prolonged
periods of use or higher than normal ambient
temperatures such as lighting public or shared
spaces or in care facilities.
Switch off the mains before commencing
installation and remove the appropriate circuit
fuse or lock off MCB.
The lamps supplied with this fitting are
consumable parts and therefore may be outside
of any warranty offered.
This unit is suitable for indoor use only.
This product is designed for permanent
connection to fixed wiring: this must be a
suitable circuit (protected with the appropriate
MCB or fuse).
This product is suitable for installation on
surfaces with normal flammability e.g. wood,
plasterboard and masonry.
Before making fixing hole(s), check that
there are no obstructions hidden beneath the
mounting surface such as pipes or cables.
Make sure that the fixings are strong enough to
support the considerable weight of the fitting
and hold it rigidly.
The chosen location of your new fitting should
allow for the product to be securely mounted
(e.g. to a plastered wall) and safely connected to
the mains supply (lighting circuit).
When choosing the location for your new fitting,
ensure that the fixings will be anchored in a solid
surface e.g. concrete, brick or a joist—do not fix
directly onto panelling, cladding, plasterboard
etc.
Do not attach to surfaces which are damp,
freshly painted or otherwise electrically
conductive (e.g. metallic surfaces).
When making connections ensure that the
terminals are tightened securely and that
no strands of wire protrude. Check that
the terminals are tightened onto the bared
conductors and not onto any insulation.
This product must be connected to earth
termination.
WARNING: This product becomes hot!
This product is not intended to be used by
children and persons with sensory, physical
and/or mental impairments that would prevent
them from using it safely.
Small children should be supervised to ensure
that they do not play with this appliance.
You are advised at every stage of your
installation to double-check any electrical
connections you have made. After you have
completed your installation there are electrical
tests that should be carried out, these tests are
specified in the current IEE wiring and building
regulations. If in doubt, consult a qualified
electrician.
CLEANING:
Clean this light fitting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
INSTALLATION:
1) Remove picture light from packaging.
2) Using the mounting bracket as a template mark the horizontal position of the fixing holes on the
mounting surface. We recommend that you use a spirit level to ensure the bracket is horizontal.
3) Fit the bracket to the mounting surface with suitable screws and wall plugs (not supplied).
4) Connect the incoming mains supply cable to the fitting using the terminal block supplied and
according to the markings.
5) Remove the 2 screws from the ends of the mounting brackets and keep to one side.
6) Fit picture light to the mounting bracket and secure with the 2 screws taking care not to trap any of
the wiring.
7) Fit 2 x 40W max E14 SES candle lamps see fig. 1 below.
8) Adjust the picture light head to the desired position. (See fig. 2 below).
9) Restore the power and switch on.
Fig 2
Front View
Recommended picturelight
head orientation
Side View
Head may be adjusted
Fig 1
Insert 2 x 40W max E14 SES
candle lamps into the holders
as shown below
