Eternal Lighting EventCUBE CW Manual de usuario

EventCUBE™ CW/WW Eternal Lighting Updated 03/2015

User Manual

EventCUBE™ CW/WW

EventCUBE™ CW/WW Eternal Lighting Updated 03/2015

Introduction:

Thank you for your purchase. The EventCUBE™ CW/WW is a DMX intelligent LED Pin Spot

light. This LED Pin Spot light is for the serious production company looking for high

powered LED output with (10) 5 Watt Cool White and Warm White LEDs. The CW/WW

LEDs can be controlled by Wireless DMX, on board push button display, wired DMX cable,

or with the PIN IR Remote (sold separately).

Unpacking: Thank you for purchasing the EventCUBE™ CW/WW light fixture. Every

EventCUBE™ has been thoroughly tested and has been shipped in perfect operating

condition. Carefully check the shipping carton for damage that may have occurred during

shipping. If the carton appears to be damaged, carefully inspect your fixture for any

damage and be sure all accessories necessary to operate the unit has arrived intact. In the

case damage has been found or parts are missing, please contact the manufacturer or your

dealer for further instructions. Do not return this unit to your dealer without first

contacting them.

Each EventCUBE™ CW/WW purchase includes:

•EventCUBE™ CW/WW

•Removable Hanging Bracket

•Charging Cord

•Padded Soft Carry Case for the EventCUBE™

•Adjustable Telescoping Tripod (Maximum Extended Height 8 Feet)

•Carry Bag for the Tripod

Additional item(s) sold separately:

•PIN IR Remote

FIRST CHARGE YOUR FIXTURE FOR 6 HOURS.Plug the IEC power cord into a

power strip connected to a wall outlet that supports 100-220V/50-60Hz. Have the Power

Switch in the OFF position and Receiver Switch in the OFF position. Securely, plug the IEC

power cord in the Power Input on the side of the light fixture. The Battery Charge Indicator

will illuminate Red while charging or illuminate Green when light fixture reaches 80% or

higher battery charge.

NOTE: You can be charging the EventCUBE™ and turn on the Power Switch to use the fixture.

EventCUBE™ CW/WW Eternal Lighting Updated 03/2015

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to

rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself; doing so will void your manufactures warranty. In the unlikely event your unit

may require service please contact the manufacturer or your dealer.

How Long Does the Battery Last?

The EventCUBE™ CW/WW will last up to 8 hours on a single full charge at full brightness. You

can adjust the brightness of the LEDs by DMX controller or by push button display to

prolong the battery per charge.

Features & Technical Specifications:

•(10) Zoomable Heads, each with (1) 5 Watt Cool White and (1) 5 Watt Warm White LED

•USITT DMX-512 (1CH, 10CH DMX Mode)

•Flicker Free Refresh Rate >400 Hz (HDTV Video, Guaranteed No Flicker)

•Ideal for ideal for HDTV recordings with Flicker Free operation

•16 Digit, 2 Line, Full Text read out Back-Lit LCD Push Button Display

•Power In & Power Out

•3-Pin Input/Output

•Master/Slave Control

•Up to 8 Hours of Battery Life

•Flush Mounted Wireless DMX Antenna recessed to keep the antenna safe

•2.4gHz Wireless DMX Receiver that is also a Transmitter (Up to 300ft Line of Sight)

•Simultaneous master signal transmitting from Master to all other lights in range

•IR Remote control. Also the Signal Received from the IR Remote can transmit to the other

lights by Wireless DMX

•Removable Hanging Bracket

•EventCUBE ™ CW/WW weighs 20 lbs

•Dimensions on EventCUBE™ CW/WW: 35” x 2.5” x 3” (Body) 35” x 2.5” x 10” (Body &

Heads)

•Dimensions on Tripod: 7.2” x 6.5” x 60”

•Beam Angle: 3° to 20° Zoomable Pin Spot Heads

•LED Life Rating: 50,000 hours

EventCUBE™ CW/WW Eternal Lighting Updated 03/2015

Operation Guide:

Start Up Welcome to ETERNAL LIGHTING

Switch to Display Version

DMX addr

CH mode

DMX address: 001-512

CH Mode 01 / 10

Mast/Slave

Mast / Slave

Programs

Program 01, Program 02, Program 03, Program 04

Boot Time/Work Time

Current operating time and total run time

Battery Capacity

Battery Percentage Indicator

(90-100% is Fully Charged, 20-30% is Low to Depleted Battery)

Note: Light will shut off around 20-30% left on Battery Capacity

LCD Display time

10 seconds through 60 seconds or Full on

IR INFA

Enable/Disable for IR Sensor

Menu:

oStart Up – Welcome to Eternal Lighting Screen

oDMX Address and Channel Mode – Press Enter to move up and down between

DMX Addr and CH. Press Down/Up to scroll through choices. Press Enter to save a

command then press Menu to back out.

oMaster/Slave – Press Up or Down to change the command of Master or Slave, Enter

to save the command. (NOTE: In order to use the PIN IR Remote, put the fixture in

Master Mode. The fixture will not respond to the PIN IR Remote if it is in Slave

Mode.)

oPrograms-

oProgram 01: All 10 Heads Warm White. Press Enter and manually control 0-

255 brightness by pressing up and down.

EventCUBE™ CW/WW Eternal Lighting Updated 03/2015

oProgram 02: All 10 Heads Cool White. Press Enter and manually control 0-

255 brightness by pressing up and down.

oProgram 03: Head 1-5 Warm White, Head 6-10 Cool White. Press Enter and

manually control 0-255 brightness by pressing up and down.

oProgram 04: Every other Head is Warm White and Cool White. Press Enter

and manually control 0-255 brightness by pressing up and down.

oBoot Time and Work Time – Current operating time and total run time

oBattery Capacity – Indication of Percentage left on the battery

oLCD Display Time – Choose to have the Display back lit Full On/10sec-60sec

oIR INFA – Enable or Disable

How to use the Wireless Receiver: Turn the wireless Receiver button to the ON position.

There is a Wireless Indicator that illuminates the colors in the ID Code Selector.

ID Code Selector – Red (1), Green (2), Yellow (3), Blue (4), Purple (5), Cyan (6), White (7).

To change to ID Code Selector colors, press the small clickable button next to the ID Code

Selector.

Master/Slave - Have one fixture in Master Mode and the rest of the fixtures in Slave Mode.

Turn on the Receiver button and put all fixtures on same ID Code Color. You now control

only the Master fixture and all the Slave fixtures will do what the Master is doing. The

Master fixture Wireless Indicator will start blinking RED (meaning transmitting signal) and

all the Slave fixture(s) will start blinking GREEN (meaning receiving signal).

Helpful Trick: To Master Reset the EventCUBE™ CW/WW to Factory setting, press Menu

and Enter button at the same time and hold for 5 seconds. The light will go into the

following factory settings. Address will go back to 001, CH mode 01, Manual values to 255,

IR INFA disabled.

Infrared remote control: (PIN IR Remote is Sold Separately)

To use the IR remote control on the EventCUBE™ CW/WW, first ENABLE the IR INFA located

in the MENU selection. Also, turn the fixture into a MASTER. To control the fixture you must

aim the remote at the infrared sensor located by the Display (front and back of fixture).

EventCUBE™ CW/WW Eternal Lighting Updated 03/2015

DMX Values and Functions:

DMX Channel Mode 1ch/10ch

1 CH Mode EventCUBE™ DMX CW/WW

Value

CW/WW 5 Watt LED

CH1

0-255

0-10: OFF

11-61: Warm White all 10 Heads Dim to Bright

62-124: Cool White all 10 Heads Dim to Bright

125-185: Head 1-5 WW and Head 6-10 CW Dim to Bright

186-255: Every other Head CW/WW Dim to Bright

10 CH Mode EventCUBE™ DMX CW/WW

Value

CW/WW 5 Watt LED

CH1 (Head 1) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

CH2 (Head 2) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

CH3 (Head 3) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

CH4 (Head 4) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

CH5 (Head 5) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

EventCUBE™ CW/WW Eternal Lighting Updated 03/2015

For more information, please contact Support by email at support@eternallighting.com

CH6 (Head 6) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

CH7 (Head 7) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

CH8 (Head 8) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

CH9 (Head 9) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

CH10 (Head 10) 0-255

0-10: OFF

11-123: Warm White Dim to Bright

124-255: Cool White Dim to Bright

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de iluminación de Eternal Lighting

Eternal Lighting

Eternal Lighting STELLAR6OXT Manual de usuario

Eternal Lighting

Eternal Lighting EchoICON Manual de usuario

Eternal Lighting

Eternal Lighting CUBEecho RGBWA+UV Manual de usuario

Eternal Lighting

Eternal Lighting CUBEecho RGBWA Manual de usuario

Eternal Lighting

Eternal Lighting EchoICON Manual de usuario

Eternal Lighting

Eternal Lighting FlatParPro-10W Manual de usuario

Eternal Lighting

Eternal Lighting EchoMATE Manual de usuario

Eternal Lighting

Eternal Lighting ULTRA170 CW/WW Manual de usuario

Eternal Lighting

Eternal Lighting EliteParHEX Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario