ETC Source Four Manual de usuario

ETC Quick Guide

Source Four LED™Profile

Source Four LED Profile Page 1 of 8 Electronic Theatre Controls, Inc.

Corporate Headquarters



3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA



Tel +608 831 4116



Fax +608 836 1736

London, UK



Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK



Tel +44 (0)20 8896 1000



Fax +44 (0)20 8896 2000

Rome, IT



Via Pieve Torina, 48, 00156 Rome, Italy



Tel +39 (06) 32 111 683



Fax +44 (0) 20 8752 8486

Holzkirchen, DE



Ohmstrasse 3, 83607 Holzkirchen, Germany



Tel +49 (80 24) 47 00-0



Fax +49 (80 24) 47 00-3 00

Hong Kong



Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong



Tel +852 2799 1220



Fax +852 2799 9325

Service:

(Americas) service@etcconnect.com



(UK) service@etceurope.com



(DE) techserv-hoki@etcconnect.com



(Asia) service@etcasia.com

Web:

www.etcconnect.com



Product information and specifications subject to change.

7460M1300-1.7.0



Rev A



Released 2014-12



ETC intends this document to be provided in its entirety.

Overview

For complete information and step-by-step instructions, see the Source Four LED Profile User Manual.

ETC documentation can be downloaded at www.etcconnect.com.

Accessory

holder

Yoke

Accessory

retainer

Yoke

locking knob

Safety cable

loop

LCD

DMX Thru

DMX In

Keypad

Power In

Power Thru

Status

indicators

Light Bulb

Home

Back

Enter

Down

Power – Indicates AC power is On.

DMX – Indicates control signal is Active.

Error – Indicates data error, high temperature, or other unusual status.

All manuals and user guides at all-guides.com

all-guides.com

ETC Source Four LED Quick Guide

Install

Source Four LED Profile Page 2 of 8 Electronic Theatre Controls, Inc.

Install

Lens Tube

Step 1: Slide the lens tube into the shutter barrel.

Step 2: Tighten the lens zoom knob.

Step 3: Tighten the Phillips screw at the top of the lens barrel.

Install Fixture

Step 1: Hang or mount the fixture.

Step 2: Attach a safety cable.

Step 3: Insert additional accessories such as a top hat, etc.

WARNING:

Use only hardware rated for total weight of fixture and accessories.

A safety cable (or other approved safety device) must be securely attached to

the safety cable loop before loosening the clamp.

Disconnect the unit from power and DMX and allow the fixture to cool before

removing or installing the shutter barrel or other adapters, and all cleaning and

maintenance.

Low clearance position

General use position

All manuals and user guides at all-guides.com

ETC Source Four LED Quick Guide

Connect

Source Four LED Profile Page 3 of 8 Electronic Theatre Controls, Inc.

Connect

Step 1: Attach the power cable to the Power In connector.

Step 2: Attach the 5-pin XLR cable to the DMX In connector (if using external control).

Step 3: Connect the power cable to AC power.

Step 4: Plug the XLR cable (if using) into the data source.

Step 5: Link additional fixtures via Power Thru and DMX Thru connectors.

Focus

Step 1: Supply power and wait for the fixture to boot up.

Step 2: Press []to open the Presets & Sequences menu.

Step 3: Select Focus and press []to turn on the LED array.

Step 4: Adjust the fixture to the desired position.

Step 5: Once focus is set, press []to turn off the LED array and then []to return to home

screen.

WARNING:

No more than nine total Source Four LED (four total Series 2 Lustr) fixtures on

Power Thru (non-dimming, 100 to 240 VAC, 50/60 Hz)

Up to 32 device loads can be on one DMX daisy-chain.

WARNING:

The fixture must be connected to a non-dimmable power source in order to

avoid damage to its internal power supply and other electrical components.

Dimming will damage the fixture and void the warranty.

Power In

Power Thru

DMX In

DMX Thru

All manuals and user guides at all-guides.com

ETC Source Four LED Quick Guide

Soft Focus Diffuser

Source Four LED Profile Page 4 of 8 Electronic Theatre Controls, Inc.

Soft Focus Diffuser

Step 1: Install the diffuser into an A-Sized Pattern holder.

Step 2: Install a pattern in front of the diffuser, if needed.

Step 3: Insert the pattern holder with diffuser into the Pattern holder slot, making sure the

writing on the diffuser faces the front of the fixture.

Address

Step 1: From the home screen, press []to open the Main Menu.

Step 2: In the Main Menu, scroll to DMX Start Address, press [].

Step 3: Use []or []to scroll to the desired fixture address.

Step 4: Press []to select the address number.

Step 5: Press []to return to the home screen.

* DMX address is not needed if using standalone or master/slave control.

Features

Quick Color (Lustr+, Series 2 Lustr, Series 2 Daylight HD, Series 2 Tungsten HD, and

Studio HD)

Quick Color allows you to easily select a color and its intensity from a predefined menu. This

feature overrides any presets or sequences previously selected and is only available when

there is no external DMX signal to the fixture.

To select a Quick Color:

Step 1: Within the Presets and Sequences screen, scroll to Quick Color and press [].

Step 2: Scroll to Color and press [].

Step 3: Scroll to the desired color and press [].

Step 4: Scroll to Intensity and press [].

Step 5: Scroll to adjust the fixture’s intensity and press []to commit the selection.

Step 6: To exit the Quick Color menu, press [].

Note:

Exiting the Quick Color menu will return the fixture to the state it was in prior to

entering the menu.

All manuals and user guides at all-guides.com

ETC Source Four LED Quick Guide

Features

Source Four LED Profile Page 5 of 8 Electronic Theatre Controls, Inc.

Quick Setup

Step 1: On the Main Menu, scroll to Quick Setups and press [].

Step 2: Scroll to the desired setup and then press [].

An asterisk (*) indicates which setup is active.

Step 3: Press []to return to the home screen.

The top line of the home screen displays the name of the active setup.

Individual features and settings are adjustable under the Advanced menu. Consult the User

Manual for more information on advanced features of Source Four LED fixtures.

Lustr+, Series 2 Lustr, Series 2 Daylight HD, Series 2 Tungsten HD, and Studio HD

Tungsten and Daylight

Quick

Setup Profile Features Recommended For:

General Direct

Standard dimming curve,

regulated output for color

consistency.

Factory default: for general purpose

use, including interior architectural

applications

Stage HSI

Plus 7 enabled

Incandescent dimming curve,

regulated output for color

consistency, 3200K white point

setting

Theatrical lighting: duplicates the color

and dimming behavior of tungsten and

stage lighting fixtures

High

Impact RGB

Quick dimming curve, boost

mode for maximum intensity,

5600K white point setting

Event lighting: enables quick response,

simple RGB control and strobe channel

for maximum effect usage

Studio Studio

Linear dimming curve,

regulated output mode for

color consistency

Studio factory default: enables three-

parameter control of white light

(intensity, white point, and tint) via DMX

from a console or console-free fixture

display

Quick

Setup Profile Features Recommended For:

Studio Studio Linear dimming curve, regulated

output for intensity stability

Enables control of intensity from

luminaire’s user interface; no console

required

Single

Channel Direct

Standard dimming curve,

regulated output for color

consistency

For general purpose architectural use

Stage Direct Incandescent dimming curve,

regulated output

Matches conventional luminaire

performance

All manuals and user guides at all-guides.com

ETC Source Four LED Quick Guide

Features

Source Four LED Profile Page 6 of 8 Electronic Theatre Controls, Inc.

DMX Profiles

Lustr+, Series 2 Lustr, Series 2 Daylight HD, Series 2 Tungsten HD, and Studio HD

DMX

Profile

DMX

Channels Channel Assignments Notes

Direct 10

See Channel

assignments in direct

mode chart below

Direct control of each individual color with a

separate master intensity channel. Color

calibration of LEDs is not active in this mode.

The ten-channel profile will produce the highest

quality color cross fades.

RGB

(Ch. 4 not

used)

1-Red

Effectively addresses all seven colors via three

channels of control. RGB profile will produce

medium quality color cross-fades

2-Green

3-Blue

4 - n/a

5 - Strobe

6-Fan Control

HSI 6

1 – Hue (coarse)

High resolution hue (two channels), saturation,

and intensity control.

HSI mode will produce color cross-fades around

the color space.

2 – Hue (fine)

3 - Saturation

4 - Intensity

5- Strobe

6-Fan Control

HSIC 7

1 – Hue (coarse)

High-resolution hue, saturation, and intensity

control as above, with the addition of a color

point channel to adjust the color temperature of

the fixture in both white light and color. Color

cross-fade performance is the same as HSI.

2 – Hue (fine)

3 - Saturation

4 - Intensity

5 - Strobe

6 - Fan Control

7-Color Point (CCT)

Studio

(Ch. 4 not

used)

1 – Intensity

Controls fixture as a white light unit. If no DMX

is present, (i.e. console input), a fixture can be

adjusted for these three parameters on the U/I

at the back of the unit.

2 – Color Point (CCT)

3 - Tint

4 - n/a

5 - Strobe

6 - Fan Control

Additional profile options (on following page)

Plus 7

Seven additional precision color-control override channels are available for

use with RGB, HSI, and HSIC input profile settings. For example HSI with

‘Plus 7’ enabled becomes an 15-channel profile:

See Plus7 profile

options chart below

The desired color and intensity are achieved by

using the HSI or RGB channels

Placing the Plus7 channel at a value over 51%

gives the fixture additional channels in its profile.

Channels 9-15 represent the native colors of the

fixture and allow the operator to adjust individual

color channels to fine tune the color output.

Strobe Variable strobe control: 0% is no strobe. The fixture output will strobe more

rapidly as the strobe channel value approaches 100%.

All manuals and user guides at all-guides.com

all-guides.com

ETC Source Four LED Quick Guide

Features

Source Four LED Profile Page 7 of 8 Electronic Theatre Controls, Inc.

Channel assignments in direct mode

Plus7 profile options

Tungsten and Daylight

Channel

Number

Series 1

Studio HD

Series 1

Lustr+

Series 2

Lustr

Series 2

Daylight HD

Series 2

Tungsten HD

1 Red Red Red Red Red

2 Red Orange White Lime (not used) Red Orange

3 Mint Amber Amber Mint Mint

4 Blue Green Green Blue Blue

5 Indigo Cyan Cyan Indigo Indigo

6 n/a Blue Blue Intensity Intensity

7 n/a Indigo Indigo Strobe Strobe

8 Intensity Intensity Intensity Fan Control Fan Control

9 Strobe Strobe Strobe (not used) (not used)

10 Fan Control Fan Control Fan Control (not used) (not used)

Channel

Number

Series 1

Studio HD Series 1

Lustr+

Series 2

Lustr

Series 2

Daylight HD

Series 2

Tungsten HD

1 Hue (course) Hue (course) Hue (course) Intensity Intensity

2 Hue (fine) Hue (fine) Hue (fine) Color Temp Color Temp

3 Saturation Saturation Saturation Tint Tint

4 Intensity Intensity Intensity Strobe Strobe

5 Strobe Strobe Strobe Fan Control Fan Control

6 Fan Control Fan Control Fan Control n/a n/a

7 n/a n/a n/a Plus7 Control

on/off

Plus7 Control

on/off

8Plus7 Control

on/off

Plus7 Control

on/off

Plus7 Control

on/off Red Red

9 Red Red Red Mint Red Orange

10 Red Orange White Lime Blue Mint

11 Mint Amber Amber Indigo Blue

12 Blue Green Green (not used) Indigo

13 Indigo Cyan Cyan (not used) (not used)

14 (not used) Blue Blue (not used) (not used)

15 (not used) Indigo Indigo (not used) (not used)

DMX

Profile

DMX

Channels

Channel

Assignments Notes

Studio 3

1 - Intensity Control of parameters is also enabled from the

luminaire's user interface. No console is required

2 - Strobe

3 - Fan Control

Direct 3

1 - Intensity

2 - Strobe

3 - Fan Control

All manuals and user guides at all-guides.com

ETC Source Four LED Quick Guide

Typical Power Consumption

Source Four LED Profile Page 8 of 8 Electronic Theatre Controls, Inc.

Typical Power Consumption

Lustr+

Series 2 Lustr

Studio HD

Daylight

Tungsten

Series 2 Daylight HD

Series 2 Tungsten HD

90V 120V 240V

Idle Power / Current 4.27W / 0.084A 4.38W / 0.079A 4.2W / 0.068A

100% Boost Power / Current 130.8W / 1.48A 129.9W / 1.11A 126.4W / 0.576A

90V 120V 240V

Idle Power / Current 6.77W / 0.144A 6.9W / 0.149A 6.5W / 0.155A

100% Boost Power / Current 173.0W / 1.94A 171.0W / 1.44A 168.0W / 0.783A

100V 120V 240V

Idle Power / Current 5.69W / 0.096A 5.71W / 0.091A 5.35W / 0.073A

100% Boost Power / Current 129.2W / 1.3A 127.1W / 1.07A 126.2W / 0.564A

90V 120V 240V

Idle Power / Current 4.3W / 0.083A 4.35W / 0.077A 4.04W / 0.066A

100% Boost Power / Current 165.2W / 1.87A 163.3W / 1.39A 160.3W / 0.718A

100V 120V 240V

Idle Power / Current 4.3W / 0.085A 4.35W / 0.078A 4.0W / 0.065A

100% Boost Power / Current 159.8W / 1.81A 157.4W / 1.35A 154.8W / 0.695A

100V 120V 240V

Idle Power / Current 5.58W/0.093A 5.69W/0.088A 4.9W/0.06A

100% Boost Power / Current 246.6W/2.481A 245.2W/2.58A 242.3W/1.111A

100V 120V 240V

Idle Power / Current 5.64W/0.095A 5.71W/0.091A 4.9W/0.061A

100% Boost Power / Current 210.1W/2.115A 208.5W/1.752A 205.4W/0.963A

All manuals and user guides at all-guides.com

Otros manuales para Source Four

Tabla de contenidos

Otros manuales de Equipo de DJ de ETC

ETC

ETC Desire series Guía de configuración

ETC

ETC Releve Spot Instrucciones de montaje

ETC

ETC Congo jr Master Playback Wing Manual de usuario

ETC

ETC Source Four Mini LED Manual de usuario

ETC

ETC ColorSource CYC Manual de usuario

ETC

ETC Source Four PARN Manual de usuario

ETC

ETC F-Drive R12 Series Manual de usuario

ETC

ETC Irideon WLZ Manual de usuario

ETC

ETC Desire XTI Series Manual de usuario

ETC

ETC Desire D40 Manual de usuario

ETC

ETC ColorSource Manual de usuario

ETC

ETC CE Source Four Guía de configuración

ETC

ETC High End Systems SHOWGUN Manual

ETC

ETC Source 4WRD II Manual de usuario

ETC

ETC Source Four Mini LED Manual de usuario

ETC

ETC Desire series Manual de usuario

ETC

ETC ColorSource PAR Manual de usuario

ETC

ETC Source Four Zoom Manual de usuario

ETC

ETC ColorSource Spot V 1.0 Manual de usuario

ETC

ETC ColorSource Linear Manual de usuario

ETC

ETC fos/4 Series Manual de usuario

ETC

ETC Source Four XT HID Zoom Grid Louver Manual de usuario

ETC

ETC Source Four LED Series Manual de usuario

ETC

ETC Desire series Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario