Etatron EOne Manual de usuario

Part A: Attaching the discharge tubing to the top stem on the solenoid

Remove the

discharge valve nut.

Remove the protective

cap by popping it out.

Insert the opaque

tubing through

the nut.

Slide the locking collar

onto the tubing.

Insert the barb fitting

onto the tube.

Screw the nut back onto

the discharge valve.

The locking collar will

slide onto the barb

creating a compression

fitting.

Cut the injection valve to your specifications. Then insert it

into the water line so that the end of the injection valve is

midway in the pipe as seen below.

Attach the other end of

the tubing to the

injection valve following

steps 2 - 5.

Congratulations on your new Etatron.

Please read the following important information.

NEED HELP? CALL 800-451-6628

Included in Box

• eOne Basic Pump

• Bracket Mounting Kit

• Operating Instructions and Maintenance Manual

• Allen Wrench (to remove solenoid when needed)

• Hose Packet

- Opaque, Rigid PE Tubing for the Discharge

- Clear, Flexible, PVC Suction Tube

- Injection stem

- Foot Filter

NOTE: Remove safety labels before installing and

remember that pumps may hold water inside.

(See back for Part B)

eOne Basic Quick Start Guide

Flow rate 1.32 GPH, Max. pressure 101 PSI

NOTE: The

injection valve

comes as

1/2”, 3/8” or

M10 MPT.

- See operating manual for complete instructions and

safety standards. Barb

- When connecting a metering pump either to a public

water supply or to its own water source, you must

respect the regulations in force concerning protection

of the soursce i.e. backflow prevention, etc.

CAUTION

Part B: Attaching the PVC exible suction valve tubing

Cut the clear PVC flexible tubing into two

pieces that are the correct size for your

application.

Then, attach one of the two clear PVC tubes

to the suction valve barb following

steps 2 - 5 on the previous page.

Reattach the nut to the suction valve.

Using the other end of the clear PVC

tubing, attach the foot filter using steps

2 - 5 on the previous page. Place the foot

filter into the stock solution tank.

Now take the other piece of PVC tube

(priming discharge tube) and attach it to the

bleed barb. Place the other end into the stock

solution tank.

To prime the pump, set the frequency

adjusting knob to 100%. Then, plug the

pump in and press the start button.

Unscrew the bleed valve nut and the

solution will begin to go down through the

priming discharge tube. Once this has

finished, re-tighten the nut.

NOTE: The eOne Basic is a manual pump. The dial

option has a 0-100% to 0-20%. The 0-20% function

can be selected by pressing the F button. The indica-

tor light will illuminate on the percentage that is select-

ed. This function increases the distance on the scale

for accurately dialing down for lower dosing.

Basic Installation

Otros manuales de Bomba de agua de Etatron

Etatron

Etatron DLX-MF/M Instrucciones de uso

Etatron

Etatron eOne MF 0110 Manual de usuario

Etatron

Etatron DLX Instrucciones de uso

Etatron

Etatron DLX-MA/AD series Instrucciones de uso

Etatron

Etatron BT MA/M Instrucciones de uso

Etatron

Etatron eOneMa Manual de usuario

Etatron

Etatron eOne PLUS Instrucciones de uso

Etatron

Etatron DLX-pH/M SERIES Instrucciones de uso

Etatron

Etatron BH3-V Instrucciones de uso

Etatron

Etatron eSelect M 1 CI Instrucciones de uso

Etatron

Etatron HD-MA Instrucciones de uso

Etatron

Etatron eOne MF Series Instrucciones de uso

Etatron

Etatron DLXB pH-RX-CL Series Instrucciones de uso

Etatron

Etatron BT Series Instrucciones de uso

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario

Etatron eOne Manual de usuario

Manuales populares de Bomba de agua de otras marcas