ETAS ES4435.1 Manual de usuario

ES4435.1 Current Source Load Board

User’s Guide

The data in this document may not be altered or amended without special noti-

fication from ETAS GmbH. ETAS GmbH undertakes no further obligation in rela-

tion to this document. The software described in it can only be used if the

customer is in possession of a general license agreement or single license. Using

and copying is only allowed in concurrence with the specifications stipulated in

the contract.

Under no circumstances may any part of this document be copied, reproduced,

transmitted, stored in a retrieval system or translated into another language

without the express written permission of ETAS GmbH.

The names and designations used in this document are trademarks or brands

belonging to the respective owners.

V1.0.0 R03 EN - 08.2018

ES4435.1 Current Source Load Board - User’s Guide 3

Contents

ETAS Contents

1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Basic Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.2.1 Correct Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.2.2 Labeling of Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.3 Identifications on the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.3.1 KC Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.4 Taking the Product Back and Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1 Current Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1.1 Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1.2 Switched Battery Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1.3 Calibrating the Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.2 Configuration in LABCAR-RTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.3 Assigning “Load in Slot x” to Connector “Load n” . . . . . . . . . . . . . . . . . . 13

2.4 The Load Signals at the Backplane Connectors . . . . . . . . . . . . . . . . . . . . . . 14

3Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4ETAS Contact Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

ES4435.1 Current Source Load Board - User’s Guide4

Contents ETAS

ES4435.1 Current Source Load Board - User’s Guide 5

ETAS Introduction

1 Introduction

This User’s Guide describes the ES4435.1 Current Source Load Board.

It consists of the following chapters:

• "Introduction" on page 5

This chapter – here you will find general information on the ES4435.1

Current Source Load Board.

• "Hardware" on page 11

This chapter describes the individual function units of the ES4435.1 Cur-

rent Source Load Board in more detail.

• "Technical Data" on page 15

This section contains the technical data of the ES4435.1 Current Source

Load Board

CAUTION!

Some components of the ES4435.1 Current Source Load Board may

be damaged or even destroyed by static discharge. Leave the board in

its transport package until you want to install it.

The ES4435.1 Current Source Load Board should only be taken from

its package, configured and installed at a working place that is pro-

tected against static discharge.

WARNING!

The components, connectors and conductors of the ES4435.1 Cur-

rent Source Load Board may carry dangerous voltages. These voltages

may even exist if the ES4435.1 is not installed in the ES4408.1 Load

Chassis or the ES4408.1 Load Chassis is powered off.

Make sure the ES4435.1 is protected against contact during opera-

tion.

CAUTION!

If cards are unlocked (e.g. during setup or calibration) but not com-

pletely removed from the housing, they nevertheless have to be

pulled out of the housing so that the distance between the card and

the backplane of the housing is at least 1 cm! Otherwise there could

be contacts between the cards which could then be destroyed as a

result.

ES4435.1 Current Source Load Board - User’s Guide6

Introduction ETAS

1.1 Features

The ES4435.1 Current Source Load Board is a 3 U plug-in board for the ES4408.1

Load Chassis and is used to simulate low current loads up to 150 mA.

A total of seven boards of the type ES4434.1 Configurable Load Board and

ES4435.1 Current Source Load Board can be installed in the ES4408.1 Load

Chassis.

The ES4435.1 Current Source Load Board has the following features:

• 24 current sources

• Current direction can be set for every current source in LABCAR-RTC

• Every current source can drive currents of 5...150 mA (at 6 V...20 V bat-

tery voltage)

• Power limitation 3 W/current source – with higher battery voltages (up to

60 V max.) the maximum permissible current will be limited accordingly

• Current sources are enabled/disabled depending on the status of a spe-

cific battery node – sources are also assigned to battery nodes in LABCAR-

RTC.

This makes the ES4435.1 Current Source Load Board suitable for projects in

which frequent reconfigurations are necessary – for rare changes, we would rec-

ommend the ES4434.1 Configurable Load Board which can accommodate 24

manually configurable loads.

ES4435.1 Current Source Load Board - User’s Guide 7

ETAS Introduction

Fig. 1-1 shows the block diagram of the ES4435.1 Current Source Load Board.

Fig. 1-1 Block Diagram of the ES4435.1 Current Source Load Board

FPGA

Status BN[0...5]

SPI

JTAG

Current Source10

Current Source 1

Current Source 2

Current Source 3

Current Source 4

Current Source 5

Current Source 6

Current Source 7

Current Source 8

Current Source 9

Current Source 11

Current Source 12

Current Source 22

Current Source 13

Current Source 14

Current Source 15

Current Source 16

Current Source 17

Current Source 18

Current Source 19

Current Source 20

Current Source 21

Current Source 23

Current Source 0

ES4435.1 Current Source Load Board - User’s Guide8

Introduction ETAS

1.2 Basic Safety Instructions

Please adhere to the safety instructions in this manuals to avoid injury to yourself and

others as well as damage to the device.

1.2.1 Correct Use

ETAS GmbH cannot be made liable for damage which is caused by incorrect use and not

adhering to the safety instructions.

1.2.2 Labeling of Safety Instructions

The safety instructions contained in this manual are shown with the standard danger sym-

bol shown below:

The following safety instructions are used. They provide extremely important information.

Please read this information carefully.

CAUTION!

indicates a low-risk danger which could result in minor or less serious injury

or damage if not avoided.

WARNING!

indicates a possible medium-risk danger which could lead to serious or even

fatal injuries if not avoided.

DANGER!

indicates a high-risk, immediate danger which could lead to serious or even

fatal injuries if not avoided.

ES4435.1 Current Source Load Board - User’s Guide 9

ETAS Introduction

1.3 Identifications on the Product

The following Symbols are Used for Product Labeling:

1.3.1 KC Mark

With the KC mark attached to the product and its packaging, ETAS confirms that

the product has been registered in accordance with the product-specific KCC

guidelines of the Republic of Korea.

Symbol Description

Marking for KCC conformity

(see "KC Mark" on page 9)

Marking for conformity with WEEE directive

(see "Taking the Product Back and Recycling" on page 10)

ES4435.1 Current Source Load Board - User’s Guide10

Introduction ETAS

1.4 Taking the Product Back and Recycling

The European Union has passed a directive called Waste Electrical and Electronic

Equipment, or WEEE for short, to ensure that systems are setup throughout the

EU for the collection, treating and recycling of electronic waste.

This ensures that the devices are recycled in a resource-saving way representing

no danger to health or the environment.

Fig. 1-2 WEEE Symbol

The WEEE symbol on the product or its packaging shows that the product must

not be disposed of as residual garbage.

The user is obliged to collect the old devices separately and return them to the

WEEE take-back system for recycling.

The WEEE directive concerns all ETAS devices but not external cables or batteries.

For more information on the ETAS GmbH Recycling Program, contact the ETAS

sales and service locations (see "ETAS Contact Addresses" on page 17).

Tabla de contenidos

Manuales populares de Electricidad industrial de otras marcas

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Manual técnico

Abtech

Abtech HVJB Series Guía

Murata

Murata GRM0335C1H8R1DA01 Series Manual de usuario

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Manual de usuario

Eaton

Eaton Ulusoy HMH24-04 Manual de usuario

Newlong

Newlong NP-7H Manual de usuario

Murata

Murata GJM0335C1E4R4BB01 Series Manual de usuario

Stahl

Stahl 8575/12 Manual de usuario

SI Pegasus Manual de usuario

Murata

Murata GRM1555C1H2R7CA01 Seies Manual de usuario

Murata

Murata GRM0225C1E6R4BA03 Series Manual de usuario

Cooper Power Systems

Cooper Power Systems VXE15 Manual de usuario

S&C

S&C Vista SD Manual de usuario

Murata

Murata GRM0335C2A7R3CA01 Series Manual de usuario

Siemens

Siemens 3VA9988-0BM10 Manual de usuario

Siemens

Siemens SITRANS LVS100 Manual de usuario

Murata

Murata GRM32ER60G227ME05 Series Manual de usuario

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Manual de usuario