Estate Slide E-SL 450BD Series Manual de usuario
—WARNING—
Read all instrucons before beginning installaon or use of
this gate opener. This operator exerts a high level of force.
Exercise cauon at all mes and stay clear of the system
during operaon.
INSTRUCTION MANUAL
USER DRIVEN MANUAL*
Any feedback, changes, or advice we are
glad to hear it. Please contact us at
E-SL 450BD Series
*Estate Swing’s unique user driven manuals are constantly updated by installers and homeowners like yourself. We improve by hearing and applying your
feedback.
E-SL 450BD Series Instrucon Manual
Estate Swing Summary of Functions
Estate Slide Summary of Funcons
The Estate Slide is only to be used for vehicular Slide gates in a Class I seng.
Class I: A vehicular gate opener (or system) intended for use in a home of one-to-four single family
dwelling, or a garage or parking area associated therewith.
The Estate Slide automated system was designed and built for controlling vehicle access. Do not use
for any other purpose.
The Estate Slide automated system automates residenal Slide-leaf gates with leaves of up to 18’ in
length.
It consists of a locking electro-mechanical linear operator, powered by a 24V AC transformer, coupled
with control board that switches the voltage to DC to power the motor. The MASTER card can be pro-
grammed and is used to set the following: funcon logics, work mes (by self-learning) and pause
mes, leaf speed, and the sensivity of the an-crushing device.
The locking system will automacally lock when the motor is not operang. A release system enables
the gate to be moved by hand in case of a system failure.
For Your Assistance
Keep this manual safely stored aer installaon
Serial Number ________________________________
Date of Purchase _____________________________
Place of Purchase ____________________________
Have this informaon on hand while handling all service and warranty issues.
E-SL 450BD Series Instrucon Manual
Specifications & Part List
1
Model Estate Slide 450BD
Power Supply 24 V AC / 24V DC
Absorbed Power (W) 50
Absorbed Current (Amps) 10
Max Run Time 5.6 Minutes
Operang Ambient Temperature -4 °F to +124 °F
Motor Rotaonal Speed 2000r / min
Gate Leaf Max Length (.) Up to 14
Gate Leaf Max Weight (lbs.) Up to 450
Type of Limit Switch Magnec
Estate Swing Parts Included:
A) Two Remotes
B) Transformer
C) Limit Magnet
D) Release Keys
E) Baery
F) Belt
G) Motor
E-SL 450BD Series Instrucon Manual
Standard System Overview and Safety Zones
The system display below is a recommended standard system. Other approved accessories can be in-
stalled.
Photo sensors and a ashing light indicang gate movement is recommended for safety purposes.
1) Estate Slide Operator 2) Photocells (not included) 3) Key operated pushbuon (not included) 4)
Flashing lamp (not included) 5) Radio receiver (oponal)
NOTES:
1) Do not extend operator connecon cables
2) When laying electrical cables, use appropriate rigid and/or exible tube
3) Do not run any wires in the same conduit as 110 AC power that may be in the area.
This will cause unwanted interference
Important Preliminary Checks:
To ensure safety and an eciently operang automated system, make sure the following condi-
ons are observed.
• The gate and post must be suitable for being automated. Check that the structure is suciently
strong and rigid, and its dimensions and weights conform to those indicated in secon 1. In parcu-
lar, wheel diameter must be in relaon to the weight of the gate to be automated. Dimensions and
weight must match those indicated in the technical specicaons.
• Make sure the leaves move smoothly without any irregular fricon during enre travel.
• The soil must permit sucient stability for the expansion plugs securing the foundaon plate.
• Check if the upper guide and travel limit mechanical stops are installed.
We advise you to have any metalwork carried out before the automated system is installed.
2
E-SL 450BD Series Instrucon Manual
Tools Needed For Installation
3
• Power Drill
• Crescent Wrench
• Metal Drill Bits
• Hacksaw
• Flat Head Screwdriver
• Phillips Head Screwdriver
• Tape Measure
• Level
• Wire Strippers
• C-clamps
Other items that may be needed prior to commencing installaon:
• Cement, boards for a slab frame, and a trowel.
• Low voltage wire will be required to run power to your operator. See the power page for
specicaons.
• If the gate is more than 144’ from an a/c power supply then an electrician will be required
to move a supply closer.
• Depending on the current base, you may need cement to form a level mounng pad.
• A voltage meter may be necessary to run diagnosc checks.
• A digital camera will come in handy with technicians if any support is needed.
E-SL 450BD Series Instrucon Manual
Manual Operation
4
1. Key release the lever.
2. Li the lever to disengage the gears.
3. The motor will not run again unl the motor is relocked. There is a magnec sensor that allows
the motor to operate, be sure the magnet is lined up with the sensor.
E-SL 450BD Series Instrucon Manual
Creating Mounting Slab
5
1. Determine the height of your concrete pad based upon how high the gate is from the ground and where the
belt can be mounted to the gate. The minimum height from the top of the slab to the belt is 10”.
2. Pour a concrete pad for your opener to bolt to. Levelness of the pad is important. For convenience place a
piece of conduit that runs up the center of the pad and the other end is easily accessible.
3. Aer the foundaon has dried, use 7/16 concrete anchors aach the opener to the base.
NOTE: The gate opener can be placed on the le or right of the driveway. The diagram below is for being
placed on the le side of the driveway (if you are standing on the inside of the property looking out)
Mount Base
* Pad can be larger/closer to gate as long as opener is mounted at correct distance from the gate.
** Dimension can be greater if spacers are used to oset gate brackets from rear face of gate.
Spacers will need to be (Base distance from gate) - 31/8 = Spacer Width.
Concrete Slab Tips: Creang a wood rectangle with no top is a good way to form a slab. Aer the cement
dries the wood can be knocked away. The slab must be secured to the ground below. Having rebar pass into
the slab works well.
E-SL 450BD Series Instrucon Manual
Securing the Operator
6
If the height of the operator from the slab ever has to be adjusted, nuts can be inserted just on the
threads between the anchor and the boom of the opener—the opener can be moved up the
threading and the operator can rest on the nuts.
Feed any wires up through the opener while installing the opener to the base.
E-SL 450BD Series Instrucon Manual
Installation of Motor
7
Horizontal posion of gate bracket: The hole in the gate brack-
et should be mounted on the gate so it is centered with the
idler gears horizontally. Depending on how close you mounted
the gate opener from the rear face of the gate you may need to
shim your bracket to make it protrude o the back of the gate
more to achieve this.
Vercal posion of gate bracket: The hole in the gate bracket
should be level with the top of the idler gears when mounted
on the gate.
Aer idenfying the correct height for the gate bracket, bolt
the bracket to your gate frame using the three mounng holes.
The at side with a single hole should be facing in toward the
center of the gate.
On one side of the gate lay the belt into the belt aachment
bracket so the teeth of the belt mesh the teeth of the bracket.
E-SL 450BD Series Instrucon Manual
Installation of Motor
8
Lay the top of the belt bracket on the belt. It has two holes
in it. Mark and drill two holes in the belt . Then put the
bolts through the bolt bracket assembly to hold the brack-
et to the belt.
Aach the assembled belt bracket to the belt
aachment bolt.
Run the belt over the idlers and under the mechanized
gear with the belt teeth facing up.
Repeat gate bracket and belt bracket steps on the other
side of the gate to aach the other end of the belt to the
gate. The belt may need to be cut down to be ght if you
gate is not 15 feet long including tail. Do not cut the belt
unl you have run the belt through the gears to account
for the length needed for this.
Make your nal ghtening adjustments on the belt. The
belt should not have excessive sag in it (no more than 2
inch variance from furthest bracket to opener). To ghten
the belt aer mounng, move the nuts on the belt aach-
ment bolt.
Otros manuales para E-SL 450BD Series
1
Tabla de contenidos
Otros manuales de Abridor de puerta de Estate Slide
