ESpring Water Purifier Manual de usuario

water

The

perfect

supply

is here.

The World’s Best Source of Water

eSpring™ Water Puriﬁ er Owner’s Manual

U.S. Patent Numbers: D431,084; D421,089; 4,753,728; 4,859,386;

5,017,318; 5,529,689; 5,573,666 and other patents pending

Contents

Important Safeguards ....................................................................1

Important Notes ............................................................................2

Introduction ..................................................................................3

Above the Counter Existing Tap Installation ........................................4

Below Counter Tap Installation .........................................................6

How to Mount the Auxiliary Tap .......................................................6

Checking for Leaks ........................................................................8

Electronic Module Display ................................................................9

How to Read the Electronic Module Display .......................................9

Maintenance and Troubleshooting ...................................................10

Filter Replacement .......................................................................12

Installing the new Filter Cartridge ...................................................13

Testing the Water Puriﬁ er .............................................................13

Accessories and Replacement Parts ...............................................14

Speciﬁ cations ..............................................................................14

Technical Support ........................................................................14

Warranty ....................................................................................14

Satisfaction Guarantee .................................................................15

NSF Performance Data Sheet .......................................................16

Owner’s Manual

Important Safeguards

WHEN USING AN ELECTRIC APPLIANCE, BASIC SAFETY PRECAUTIONS,

INCLUDING THE FOLLOWING, SHOULD ALWAYS BE FOLLOWED TO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK, AND/OR INJURY TO PERSONS:

1. READ ALL INSTRUCTIONS BEFORE USE. If you still have questions

concerning the installation or operation of your eSpring™ Water

Puriﬁ er, contact Technical Support toll-free, on 1 800 022 034

(in Australia), or 0 800 113 444 (in New Zealand).

2. To protect against electric shock, do not place power adapter, cord,

base unit, or Electronic Module in water or other liquids.

3. Close adult supervision is required when any appliance is used by or

near children.

4. Unplug from electrical outlet before cleaning or performing routine

maintenance (i.e. replacing the Filter Cartridge).

5. To disconnect appliance from electrical power, remove power adapter

from electrical outlet.

6. Do not operate any appliance with a damaged electrical cord or plug

or after the appliance malfunctions or has been dropped or damaged

in any manner. If the power adapter or cord is damaged, it must be

replaced.

7. Use only the power adapter supplied with the Water Puriﬁ er. Use of

unapproved power adapters could cause system damage or injury.

8. Use only factory authorized replacement parts. The use of

unauthorized replacement parts may degrade both the safety and

the performance of this product and will void the Limited Warranty.

9. Do not use outdoors.

10. Do not let power cord hang over the edge of table or counter, or

touch hot surfaces.

11. For household use only. Do not use this appliance for other than the

intended use.

12. CAUTION: Regularly inspect product and plumbing ﬁ ttings for water

leaks, as water leaks can cause property damage.

13. WARNING: THE APPLIANCE MUST BE DRY BEFORE APPLYING

ELECTRICAL POWER AND BE DRY AND FREE OF LEAKS DURING

OPERATION.

14. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT ATTEMPT TO OPEN THE ELECTRONIC MODULE. NO USER

SERVICABLE PARTS ARE INSIDE THE ELECTRONIC MODULE.

REPAIRS TO THE ELECTRONIC MODULE SHOULD BE DONE ONLY

BY AUTHORIZED SERVICE PERSONNEL.

15. WARNING: To ensure proper performance, this product must be

con-nected to a reliable source of electrical power. The electrical out-

let to which this product is connected must comply with all applicable

electrical codes and requirements. Connection of this product to an

improperly installed electrical outlet or a double adapter can result in

risk of electric shock or ﬁ re. If you are in doubt as to whether the

electrical outlet is properly installed, have the outlet inspected by a

qualiﬁ ed electrician.

Please Read and Save These instructions

Important Notes

The eSpring™ Water Puriﬁ er is designed for use only with cold, bacterio-

logically suitable (potable) water.

1. System tested and certiﬁ ed by NSF International against ANSI/NSF

Standard 42, 53, 55. See Performance Data Sheet for individual

contaminants and reductions performance, page 16.

2. This Class B system conforms to ANSI/NSF 55 and contains an

ultraviolet lamp that requires replacement at intervals in accordance

with the manfacturer's instructions. The system is designed for the

supplemental bactericidal treatment of either treated and disinfected

public drinking water or other drinking water that has been tested

and deemed acceptable for human consumption by the state and local

health agency having jurisdiction. The system is designed to reduce

normally occurring non-pathogenic or nuisance microorganisms only.

Class B Systems are not intended for treatment of contaminated water.

Systems certiﬁ ed for cyst reduction may be used on disinfected waters

that may contain ﬁ l-terable cysts.

3. Installation of the Water puriﬁ er must comply with applicable laws

and regulations.

4. During normal operation, if the Water Puriﬁ er has not been used for

several hours (e.g., overnight), run water through it for 30 seconds

prior to use.

5. DO NOT use with warm or hot water, as this may damage the

Water Puriﬁ er.

6. Except for lead and a few other compounds, the eSpring Water

Puri-ﬁ er is NOT designed to remove soluble inorganic substances

such as iron, calcium, magnesium, nitrates or ﬂ uorides.

7. Plumber’s thread sealing compounds should NOT be used with the

eSpring Water Puriﬁ er.

8. DO NOT allow vegetable oil, petroleum jelly, or other lubricants,

solvents, ammonia, alcohols, acids, or strong cleaning solutions to

come into contact with the eSpring Water Puriﬁ er. They could cause

permanent damage to the housing. When cleaning, use a mild liquid

dishwashing detergent (such as DISH DROPS™ Dishwashing Liquid)

and water. DO NOT use any other cleaners or abrasive pads as they

could damage the plastic housing and auxiliary tap.

9. The eSpring Water Puriﬁ er’s Electronic Module will let you know when

it is time to replace the ﬁ lter.

10. THE FILTER CARTRIDGE MUST BE REPLACED AT LEAST ONCE A

YEAR. In areas of very poor water quality, you may see a drop in the

ﬂ ow rate, indicating that ﬁ lter replacement may be needed more

frequently. Even if water ﬂ ow rate is not affected, the ﬁ lter must be

replaced as soon as a year has passed or when it has ﬁ ltered 5000 L

of water, whichever comes ﬁ rst.

REMEMBER: OPERATIONAL, MAINTENANCE AND REPLACEMENT

REQUIREMENTS ARE ESSENTIAL FOR THIS PRODUCT TO PERFORM

AS REPRESENTED. IT IS IMPORTANT THAT ONLY THOSE REPLACEMENT

ELEMENTS THAT ARE IDENTIFIED IN THIS MANUAL ARE USED WITH

THIS PRODUCT. THE LIMITED WARRANTY DOES NOT COVER ANY

DEFECT OR DIMINISHED PERFORMANCE CAUSED BY THE USE OF

ANY PART OR ACCESSORY THAT IS NOT COMPATIBLE WITH THE

eSpring WATER PURIFIER.

NOTE: The eSpring Water Puriﬁ er is to be installed with the Existing Tap

Kit or the Auxiliary Tap Kit only.

For service under this warranty in Australia contact Technical Support

on 1800 022 034 or in New Zealand on 0800 113 444 BEFORE you

return anything.

Information can also be accessed via the Internet at: www.espring.com

and www.a2k.com.au or www.a2k.co.nz.

Introduction

Congratulations on your purchase of the eSpring™ Water Puriﬁ er. You

have made a wise investment for you and your family and have taken an

important step in improving the quality of your drinking water.

Easy to Install and Maintain

The eSpring Water Puriﬁ er is easily installed and is operational in just

minutes in most homes, apartments, and cottages. Before beginning

installation, please review the owner’s manual thoroughly to ensure proper

performance of your eSpring Water Puriﬁ er.

Maintenance is quick and easy. Replace the Filter Cartridge (carbon and

UV) at least once a year according to the instructions in this manual. It is

recommended that the tubing be replaced every two years.

To maintain maximum performance and quality drinking water, the Filter

Cartridge should be replaced once a year or as soon as you have ﬁ ltered

5000 L of water - whichever comes ﬁ rst. The eSpring Water Puriﬁ er’s

Electronic Module monitors the amount of water ﬁ ltered and keeps track

of how long the ﬁ lter has been in service. When a year has passed or as

soon as the ﬁ lter has treated 5000 L of water the Electronic Module

alerts you to replace the Filter Cartridge.

Installation overview

There are two ways to install the eSpring Water Puriﬁ er:

Above counter with an Existing Tap Kit or Below counter with an Auxiliary

Tap Kit.

Above Counter Installation

• eSpring Water Puriﬁ er

• eSpring Existing Tap Kit

Below Counter Installation

• eSpring Water Puriﬁ er

• eSpring Auxiliary Tap Kit

Installation of Filter Cartridge and connecting the Water Puriﬁ er to power

Refer to the exploded view of the eSpring Water Puriﬁ er (Fig. 1) for

assistance with part names.

The Filter Cartridge (carbon and UV) comes installed at the factory. Make

sure the cartridge is ﬁ rmly in place and the handle is down. See individual

tap kit instructions later in this manual to connect your water. The only

connections needed are water and electrical power (240 volt AC).

If you are connecting to an Existing Tap turn to page 4 for installation

instructions.

If you are connecting to an Auxiliary Tap turn to page 6 for installation

instructions.

Top Shroud

Filter Retaining Ring

Electronic Module

Filter Bracket

Filter Cartridge

Base Housing

Fig. 1

Power Adapter

Above the Counter Existing

Tap Installation

This installation is quick and simple. The eSpring™ Water Puriﬁ er sits on

the countertop with the diverter and tubing attached directly to your tap.

Existing Tap Components (Fig. 2)

Check to make sure Existing Tap Kit contains all the correct components,

before you begin installation.

a). Diverter with attached white tubing

b). 3 tap adapters includes 2 males, 1 female (knurled edge)

c). 2 tube supports

d). 2 tubing ties (nylon)

1. If there is an aerator on the end of your kitchen tap, unscrew and

remove the aerator.

2. Position the diverter onto the tap and turn the knurled revolving

collar counterclockwise until the diverter draws up tight to the tap.

If necessary, use one of the three supplied adapters to ﬁ t the

diverter to your tap (Fig. 3).

3. Use the tubing ties to neatly secure the diverter’s tubing to the base

of the tap.

4. If the tubing is too long, you may want to shorten it. Use a utility knife

to cut tubing straight to form a ﬂ at end. Do not cut where tubing is

bonded together. (Fig. 4). Do not cut tubing too short.

Fig. 2

Fig. 3

Tap

Adapter

Nylon

Hose

Tie

Diverter

Fig. 4

Above the Counter Existing

Tap Installation

This installation is quick and simple. The eSpring™ Water Puriﬁ er sits on

the countertop with the diverter and tubing attached directly to your tap.

Existing Tap Components (Fig. 2)

Check to make sure Existing Tap Kit contains all the correct components,

before you begin installation.

a). Diverter with attached white tubing

b). 3 tap adapters includes 2 males, 1 female (knurled edge)

c). 2 tube supports

d). 2 tubing ties (nylon)

1. If there is an aerator on the end of your kitchen tap, unscrew and

remove the aerator.

2. Position the diverter onto the tap and turn the knurled revolving

collar counterclockwise until the diverter draws up tight to the tap.

If necessary, use one of the three supplied adapters to ﬁ t the

diverter to your tap (Fig. 3).

3. Use the tubing ties to neatly secure the diverter’s tubing to the base

of the tap.

4. If the tubing is too long, you may want to shorten it. Use a utility knife

to cut tubing straight to form a ﬂ at end. Do not cut where tubing is

bonded together. (Fig. 4). Do not cut tubing too short.

Fig. 2

Fig. 3

Tap

Adapter

Nylon

Hose

Tie

Diverter

Fig. 4

Above the Counter Existing

Tap Installation

This installation is quick and simple. The eSpring™ Water Puriﬁ er sits on

the countertop with the diverter and tubing attached directly to your tap.

Existing Tap Components (Fig. 2)

Check to make sure Existing Tap Kit contains all the correct components,

before you begin installation.

a). Diverter with attached white tubing

b). 3 tap adapters includes 2 males, 1 female (knurled edge)

c). 2 tube supports

d). 2 tubing ties (nylon)

1. If there is an aerator on the end of your kitchen tap, unscrew and

remove the aerator.

2. Position the diverter onto the tap and turn the knurled revolving

collar counterclockwise until the diverter draws up tight to the tap.

If necessary, use one of the three supplied adapters to ﬁ t the

diverter to your tap (Fig. 3).

3. Use the tubing ties to neatly secure the diverter’s tubing to the base

of the tap.

4. If the tubing is too long, you may want to shorten it. Use a utility knife

to cut tubing straight to form a ﬂ at end. Do not cut where tubing is

bonded together. (Fig. 4). Do not cut tubing too short.

Fig. 2

Fig. 3

Tap

Adapter

Nylon

Hose

Tie

Diverter

Fig. 4

5. Insert one tube support into the open end of each tube and mark the

tubing with a line 18mm from the end of the 9.5mm tubing and

14.4mm on the 8mm tubing. (Fig. 5).

6. Remove the Top Shroud and Electronic Module from the eSpring™

Water Puriﬁ er.

7. Insert and push the diverter tubing ﬁ rmly by hand into the Filter

Bracket Quick Connectors to the marked line (Fig. 6).

NOTE: The diverter tubing has a 9.5mm O.D. tube (output) and a 8mm

O.D. tube (Output). The tubing is designed to attach only one way to the

Filter Bracket.

8. Plug the DC Jack of the power adapter into the back of the

Electronics Module.

9. Replace the Electronic Module on top of the Filter Bracket. Push

down until it seats properly. Ensure the power adapter cord and

strain relief are properly located in the cutout in the back to prevent

the cord from being damaged.

10. Replace the Top Shroud on the Water Puriﬁ er.

11. Untreated water will ﬂ ow straight through the diverter, when the pin

is in. (Fig.7).

12. Turn on the tap and pull out diverter pin (Fig. 8). Water passes into

the eSpring Water Puriﬁ er and Filter Cartridge.

13. It will take a short time for the water to saturate the Filter Cartridge

and then emerge from the diverter. When treated water begins to

ﬂ ow from the treated water port, continue to let it run consistently

for ﬁ ve minutes to eliminate air pockets and to clear the Water

Puriﬁ er of any carbon dust. (It is normal for a small amount of carbon

dust from the ﬁ lter manufacturing process to be seen during the

initial ﬂ ow.) If the water does not clear of carbon dust within 15

minutes, call Technical Support toll-free. Australia contact Technical

Support on 1800 022 034 or in New Zealand on 0800 113 444.

14. Plug the power adapter into an available electrical outlet.

NOTE: If the Electronic Module is functioning properly, the blue water

drops on the display will blink sequentially, when water is ﬂ owing through

the unit. If the blue water drops are not blinking, see Maintenance and

Trouble Shooting, pages 10 and 11.

15. Check for any signs of leakage (bubbling or water drips around

connectors). If leaking occurs, push in the diverter pin to stop the

ﬂ ow of water through the Water Puriﬁ er and shut off the tap, see

Maintenance and Trouble Shooting, pages 10 and 11.

16. If there are no leaks after ﬂ ushing the Water Puriﬁ er to eliminate

possible carbon dust, push in the diverter pin to stop the ﬂ ow of

water through the Water Puriﬁ er and turn off the tap. Your eSpring

Water Puriﬁ er is ready to use. Whenever you want treated, good-

tasting water, just turn on the cold water tap and pull out the diverter

pin. When through, simply push the diverter pin back in and turn off

the tap.

17. After you have connected your tap to the Puriﬁ er and water, check

your Electronic Module display to be sure your Puriﬁ er is functioning

properly, page 9.

Untreated

Water

Fig.7

Diverter

Fig. 5

Tube Support

14.4 mm

18 mm

Fig. 6

Input

Fig. 8

Diverter

Output

Treated

Water

Below Counter

Tap Installation

The eSpring™ Auxiliary Tap Kit must be installed by a licenced plumber.

All installations are to be performed according to local plumbing codes

and regulations.

This installation uses a separate, counter-mounted Auxiliary Tap, which is

supplied in the Auxiliary Tap Kit. With the eSpring Water Puriﬁ er below

the counter, this installation allows maximum use of counter space, and

there is no visible tubing.

REVIEW ALL INSTALLATION INSTRUCTIONS TO BE SURE YOU HAVE ALL

PARTS PRIOR TO INSTALLATION.

The Auxiliary Tap Kit is designed for use with the eSpring Water Puriﬁ er.

Contact free Technical Support for assistance at 1800 002 034 / New

Zealand 0800 113 444.

Auxiliary Tap Components (Fig. 9):

a. Auxiliary tap body with red, green and blue hoses, foam gasket, wing nut

b. Auxiliary tap spout

c. Union quick connector*

* Union Quick Connector contains a ﬂ ow control that is essential for

proper operation.

NOTE: A licenced plumber needs to supply and install an approved isolation

valve and T-connector.

IMPORTANT: If you suspect that your water pressure exceeds 860 kPa,

a plumber needs to install a pressure regulating device.

How to Mount the

Auxiliary Tap

1. Select a location for the Auxiliary Tap. There may already be an extra,

capped hole in your sink’s ledge for a sprayer or extra tap. If so,

mounting your Auxiliary Tap there will result in the easiest installation.

Just remove the cap and the hole is ready to use, no drilling needed.

2. If there is no ready-to-use capped hole, you may choose to drill a hole

in the sink ledge or counter where you want to install your Auxiliary

Tap. The hole must be at least 32mm in diameter and centered no

farther than 150mm from the sink basin. Before drilling, make sure

that you have sufﬁ cient clearance below the sink or counter to

accommodate the tap and allow you to make connections to the

eSpring Water Puriﬁ er.

NOTE: If you have a porcelain/ceramic sink, you may want to seek profes-

sional assistance for proper drilling.

3. Insert the tap spout into the main body and press into place.

4. Remove the wing nut while keeping the foam gasket in place.

5. Holding the foam gasket in place, lower the Auxiliary Tap stem and

hoses through the hole in the sink ledge or counter (Fig. 10).

6. Reach up from below the counter and place the wing nut onto the

threaded tap stem above the three attached hoses. Position the tap

in the desired orientation relative to the location of the handle (left-

handed or right-handed). Have a helper hold the tap in place while you

tighten the wing nut.

Fig. 9

Tap Body

Spout

Foam Gasket

Counter

Wing Nut

Fig. 10

WARNING: Due to the possibility of shock or electrocution, use extreme

care when operating an electric power drill or other power tools around

the sink. Make sure that no part of you or the drill comes into contact

with water or moisture at any time.

Red

Green

Blue

Red

Green

Blue