ESKUTE Star Manual de usuario
Electric Bike
www.eskute.com
User Manual
Model: Star
WELCOME!
Congratulations on the purchase of your new Star and
welcome to the Eskute team!
About
this User Manual
It is impoant for you to understand your new electric bike.
Even if you have ridden an e-bike before, it is impoant for
eve person to read this manual before riding - you’ll know
how to get better peormance, comfo, and enjoyment from
your new e-bike!
Before riding your e-bike, you
will need to charge your
batte fully before using.
Failure to do so may damage
the batte life and
peormance.
CAUTION WARNING
Don’t dismantle and repair pas by
yourself, please go to the local
distributor or the seicing station if
necessa. For any questions or
concerns, please email to
suppo@eskute.com or visit
www.eskute.com.
TABLE OF CONTENTS
Section 1. Geomet
Section 2. Specication
Section 3. Assembling Your Bike
Section 4. Fold & Unfold the Bike
Section 5. Charging the Batte
Section 6. Maintenance Instructions
Section 7. More Tips
Section 8. Warranty
Handlebars
Front Wheel
Seat / Saddle
Pedals
Tires
Brakes
Batte Care
01
02
03
06
07
16
17
10
Saddle
Geomet
Handlebar
On/O Switch
Display
Shifter
Brake
Throttle
Batte
Headlight
Front Fork
Front Brake
Frame
Tail Light
Fender
Rear Brake
Fat Tire
Rear Derailleur
01
Specication
Model
Frame Material
Batte
Range
Charger
Charging Time
Motor
Speed
Display
Sensor
Suspension
Shifter
Rear Derailleur
Front & Rear
Brakes
Suitable Height
Load Capacity
Item Weight
Up to 22 MPH
LCD Display
Speed Sensor
Hydraulic lockout, Coil spring
adjust for preload
Star
6061 Aluminum Alloy
48V, 20Ah with Samsung/LG Cells
50-80 Miles Average (estimate)
54.6V, 3A
4-5 Hour Charging
48V, 500W Sutto (Bafang) Hub Motor
SHIMANO 7 Speed
SHIMANO 7 Speed
CST, 20” x 4.0”
Hydraulic Disc Brakes
160-190 cm / 5’2”- 6’2”
125 kg / 276 lbs
74 lbs
02
1. Stem plate bolt removal 2. Tightening stem plate bolts.
STEP 1. Install the Handlebars
Assembling Your Bike
Note: DO NOT depress the brake levers before
installing the front wheel.
1. Using the Allen wrench, unscrew the 4 bolts and remove
the stem plate.
2. Place your handlebars into the groove and replace the
stem plate over the top. Tighten the bolts about 3/4this
of the way.
3. Make the nal adjustments on your handlebars position,
ensuring that they are centered and at a comfoable angle
before tightening the bolts the rest of the way.
Before assembling, check that all pas are complete and
in good condition. If you have any questions or cannot
nd the information you need in the manual, please
contact at suppo@eskute.com.
NOTE:
03
04
1. Take o the plastic protective gaps on each side, throw these
away.
2. Loosen up both bolts untill you are able to slide the wheel into
place, making sure the brake caliper slides onto the rotor and
both of the forks are properly hooked onto the wheel, fasten
and screw the bolts.
STEP 2. Install the Front Wheel
1. Remove the protective gaps
Tip: DO NOT raise the saddle higher than the safety line.
1. Loosen the seat post clamp and inse saddle post.
2. Adjust saddle to the preferred height then tighten clamp.
1. Dropping seat into bike.
2. Tighten the seat post clamp.
STEP 3. Install the Seat
05
2. Fasten both screws
1. Unfold the bike frame
2. Press the latch lock to
release mechanism.
1. Check the end cap on both pedals in order to identify the left
and right pedal.
2. Grab the wrench, and screw the pedal tightly into the correct
crank. The pedals should thread smoothly and easily if properly
aligned.
1. left vs. Right pedal
2. Attaching pedal to crank
STEP 4. Attach the Pedals
Tip: Imagine that you are sitting on the bike to correctly determine
left vs. right side.
06
Fold & Unfold the Bike Frame
Fold & Unfold the Handle Stem
3. Proceed when you achieve
the status as pictured.
4. Fasten the latch
as pictured.
1. Loosen quick release.
2. Tilt the stem slowly.
3. Fasten the stem latch upward
to lock it in place.
4. Jiggle the stem to see If it’s
rmly locked in place.
07
Charging the Batte
Tip: The batte can be charged on/o your bike. Make sure that
your motor system and batte is turned completely o
before beginning any charging procedures.
Tabla de contenidos
Otros manuales de Scooter de ESKUTE
ESKUTE
ESKUTE Polluno Manual de usuario
ESKUTE
ESKUTE Polluno Pro Manual de usuario
ESKUTE
ESKUTE Netuno Manual de usuario
ESKUTE
ESKUTE ES1 Manual de usuario
ESKUTE
ESKUTE Spark Y Manual de usuario
ESKUTE
ESKUTE Netuno Manual de usuario
ESKUTE
ESKUTE MYT-27.5 Manual de usuario
ESKUTE
ESKUTE Netuno Pro Manual de usuario
ESKUTE
ESKUTE ES MAX Manual de usuario
