ESD ECX-PoE-PE Manual de usuario
ECX-PoE-PE
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
Page 1 of 25
esd electronic system design gmbh
Vahrenwalder Str. 207 • 30165 Hannover • Germany
www.esd.eu • Fax: 0511/37 29 8-68
Phone: 0511/37 29 80 • International: +49-5 11-37 29 80
ECX-PoE-PE
Power-Extractor for InRailBus
Hardware Manual
to Product E.3020.02
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
ECX-PoE-PEPage 2 of 25
N O T E
The information in this document has beencarefullychecked andis believed to be entirelyreliable. esd
makes no warranty of any kind with regard to the material in this document, and assumes no
responsibility for any errors that may appear in this document. esd reserves the right to make changes
without notice to this, or any of its products, to improve reliability, performance or design.
esd assumes no responsibility for the use of anycircuitryother than circuitry which is part of a product
of esd gmbh.
esddoes not conveyto the purchaser of the product described herein anylicense under the patent rights
of esd gmbh nor the rights of others.
esd electronic system design gmbh
Vahrenwalder Str. 207
30165 Hannover
Germany
Phone: +49-511-372 98-0
Fax: +49-511-372 98-68
E-mail: [email protected]
Internet: www.esd.eu
USA / Canada:
esd electronics Inc.
525 Bernardston Road
Suite 1
Greenfield, MA 01301
USA
Phone: +1-800-732-8006
Fax: +1-800-732-8093
E-mail: [email protected]om
Internet: www.esd-electronics.us
Trademark Notices
EtherCAT® is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany.
All other trademarks, product names, companynames or companylogos used inthis manual are reserved by their respective
owners.
ECX-PoE-PE
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
Page 3 of 25
Document-
File:
I:\Texte\Doku\MANUALS\ECX\ECX-PoE-PE\English\ECX-POE-PE_Hardware_en_10.wpd
Date of print: 2011-02-22
PCB version: from ECX-PoE-PE Rev. 1.0
Firmware version: from Rev. 2.6
Changes in the chapters
The changes in the document listed below affect changes in the hardware and firmware as well as
changes in the description of facts only.
Chapter Changes versus previous version
- First English version
- -
Technical details are subject to change without further notice.
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
ECX-PoE-PEPage 4 of 25
Safety Instructions
!When working with ECX-PoE-PE follow the instructions below and read the manual carefully to
protect yourself and the ECX-PoE-PE from damage.
!Do not open the housing of the ECX-PoE-PE
!In order to prevent overvoltage damage due to thunder storm, unplug the ECX-PoE-PE beforehand.
!Never let liquids get inside the ECX-PoE-PE. Otherwise, electric shocks or short circuits may result.
!Protect the ECX-PoE-PE from dust, moisture and steam.
!Protect the ECX-PoE-PE from shocks and vibrations.
!The ECX-PoE-PE may become warm during normal use. Always allow adequate ventilation around
the ECX-PoE-PE and use care when handling.
!Do not operate the ECX-PoE-PE adjacent to heat sources and do not expose it to unnecessary thermal
radiation. Ensure an ambient temperature as specified in the technical data.
!Do not use damaged or defective cables to connect the ECX-PoE-PE.
Conformity
The ECX-PoE-PE is an industrial product and meets the demands of the EU regulations and EMC standards
for industrial environments printed in the conformity declaration at the end of this manual.
Warning: In a residential, commercial or light industrial environment the ECX-PoE-PE may cause radio
interferences in which case the user may be required to take adequate measures.
Qualified Personal
This documentation is directed exclusively towards qualified personal in control and automation engineering.
The installation and commissioning of the product may only be carried out by qualified personal, which is
authorized to put devices, systems and electric circuits into operation according to the applicable national
standards of safety engineering.
Intended Use
The intended use of the ECX-PoE-PE is the operation as a power extractor for InRailBus, applicable with ECX
and CBX units. The esd guarantee does not cover damages which result from improper use, usage not in
accordance with regulations or disregard of safety instructions and warnings.
!The ECX-PoE-PE is intended for indoor installation only.
!The operation of the ECX-PoE-PE in hazardous areas, or areas exposed to potentially explosive
materials is not permitted.
!The operation of the ECX-PoE-PE for medical purposes is prohibited.
Service Note
The ECX-PoE-PE does not contain any parts that require maintenance by the user. The ECX-PoE-PE does not
require any manual configuration of the hardware. Unauthorized intervention in the device voids warranty
claims.
Remove all cables before cleaning. Clean the device with a slightly moist, lint-free cloth. Cleaning agents or
solvents are not suitable.
Disposal
Devices which have become defective in the long run have to be disposed in an appropriate way or have to be
returned to the manufacturer for proper disposal. Please, make a contribution to environmental protection.
ECX-PoE-PE
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
Page 5 of 25
Contents
1. Overview ....................................................................7
1.1DescriptionoftheModule ............................................7
2. Technical Data ...............................................................9
2.1General technicalData...............................................9
2.2Microcontroller ....................................................10
3. Hardware Installation ........................................................11
3.1ConnectingDiagram ................................................11
3.2LEDDisplay ......................................................12
3.2.1 Operation of the System LED S . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2.2 Operation of the PoE LEDs P, + . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2.3 Operation of the Temperature LED T . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2.4 Operation of the Current LEDs 1, 2, 3 and W . . . . . . . . . . . . . . . . . . 14
3.3 Power Derating Depending on the Mounting Position . . . . . . . . . . . . . . . . . . . . . . 15
3.4 Installation of the Module Using InRailBus Connector . . . . . . . . . . . . . . . . . . . . . 16
3.4.1 Connection of the Power Supply Voltage . . . . . . . . . . . . . . . . . . . . . 16
3.4.2 Module Installation Using a Mounting Rail Bus Connector . . . . . 17
3.4.3 Connecting Power Supply to InRailBus . . . . . . . . . . . . . . . . . . . . . . 19
3.5 Remove the ECX Module from the InRailBus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4. Connector Assignment ........................................................20
4.1 Power Supply Voltage 24 V (X201) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2ETH(X400) ......................................................21
4.3 Power Supply Voltage via InRailBus Connector (X200) . . . . . . . . . . . . . . . . . . . . 21
4.4Ethernet(X110,X120) ..............................................22
5. Quick Start Guide ...........................................................23
6. Declaration of Conformity ....................................................24
7. Order Information ...........................................................25
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
ECX-PoE-PEPage 6 of 25
This page is intentionally left blank.
Overview
ECX-PoE-PE
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
Page 7 of 25
+24 V=
+48 V=
LEDs
Photo
Coupler
InRailBus
Connector
MEMAX
Po er Connector
MSTBO 2,5/4-
G1L-KMGY
DC/DC
Converter
Module
OVP
Gigabit Ethernet
DATA&PoE
RJ45
RJ45
DATA
Microcontroller
(PIC16)
SW-PoE
-
+
I
OUT
24V
ϑ
1. Overview
1.1 Description of the Module
Fig. 1: Block circuit diagram of the ECX-PoE-PE module
The ECX-PoE-PE is a power extractor that provides 24 V power supply voltage for the InRailBus.
It can be used for ECX and CBX units.
The power supply voltage is fed via the Ethernet lines (PoE).
The module is designed for hat-rail mounting in a control enclosure. The connectors and status LEDs
are mounted in the front panel.
The ECX-PoE-PE supports IEEE 802.03at (PoE+, layer 1 only), and is compatible with IEEE 802.03af
(Class 4).
Ethernet data (10/100/1000BASE-T) is electrically passed through.
The ECX-PoE-PE comes with LEDs which indicate the state of operation and the states of the
temperature- and the output current control.
Übersicht
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
ECX-PoE-PEPage 8 of 25
The following figure shows an example for the usage of the ECX-PoE-PE module.
Fig. 2: Exemplary installation of the ECX-PoE-PE
The ECX-PoE-PE receives the Ethernet data and the power supply for the InRailBus from the Power
Source Equipment (PSE). The 24 V power supply voltage is fed into the InRailBus and the Ethernet
data is electrically passed through to the Powered Devices (PD), e.g. to ECX-DIO8.
Technical Data
ECX-PoE-PE
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
Page 9 of 25
2. Technical Data
2.1 General technical Data
Input voltage 36 - 57 V/DC
Output voltage 24 V ± 5%
Power output maximum 25 W
(Derating from approximately 33
/
C or 41
/
C, depending on the
mounting position, see page 15)
Connectors
ETH/PoE (8-pin RJ45 jack, X110) - Ethernet Data, Power over
Ethernet (PoE)
ETH (8-pin RJ45 jack, X120) - Ethernet Data
24V (4-pin COMBICON connector with spring-cage connection,
X201) - 24V-power supply voltage
InRailBus (5-pin ME-MAX-TBUS-connector, Phoenix Contact, X200)
- power supply voltage for InRailBus
Temperature range -20 ... + 60
/
C ambient temperature
Humidity max. 90%, non-condensing
Protection class IP20
Pollution degree maximum permissible according to DIN EN 61131-2:
Pollution Degree 2
Housing Plastic housing for carrier rail mounting NS35/7,5 DIN EN 60715
Dimensions width: 22.5 mm, length: 99 mm, constructional height: 114.5 mm
(dimensions without mating connectors)
Weight approx. 135 g
Table 1: General technical data
Technical Data
Manual • Doc.-No.: E.3020.21 / Rev. 1.0
ECX-PoE-PEPage 10 of 25
2.2 Microcontroller
Microcontroller PIC16, 8 MHz
Table 2: Microcontroller
2.3 EtherNet Data & Data/PoE
Ethernet data (10/100/1000BASE-T), electrically passed through
PoE supply according to IEEE 802.03at (PoE+, only layer 1 is supported),
and compatible with IEEE 802.03 af (Class 4)
Table 3: Data of analog inputs
Tabla de contenidos
Otros manuales de Hardware de red de ESD
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
