Safety Instructions
● When working with the CPCI-ETH2 follow the instructions below and read the manual carefully to protect yourself from
injury and the CPCI-ETH2 from damage.
● The de ice is a built-in component. It is essential to ensure that the de ice is mounted in a way that cannot lead to
endangering or injury of persons or damage to objects.
● The de ice has to be securely installed in the control cabinet before commissioning.
● Protect the CPCI-ETH2 from dust, moisture and steam.
● Protect the CPCI-ETH2 from shocks and ibrations.
● The CPCI-ETH2 may become warm during normal use. Always allow adequate entilation around the CPCI-ETH2 and
use care when handling.
● Do not operate the CPCI-ETH2 adjacent to heat sources and do not expose it to unnecessary thermal radiation.
Ensure an ambient temperature as specified in the technical data.
● Do not use damaged or defecti e cables to connect the CPCI-ETH2 and follow the CAN wiring hints in chapter:
"Correctly Wiring Electrically Isolated CAN Networks".
● In case of damages to the de ice, which might affect safety, appropriate and immediate measures must be taken, that
exclude an endangerment of persons and domestic animals and property.
● Current circuits which are connected to the de ice ha e to be sufficiently protected against hazardous oltage (SELV
according to EN 60950-1).
● The CPCI-ETH2 may only be dri en by power supply current circuits, that are contact protected.
A power supply, that pro ides a safety extra-low oltage (SELV or PELV) according to EN 60950-1, complies with this
conditions.
ANGER
Hazardous Voltage - Risk of electric shock due to unintentional contact with uninsulated li e parts with high
oltages inside of the system into which the CPCI-ETH2 is to be integrated.
► Disconnect all hazardous oltages (mains oltage) before opening the system.
NOTICE
Electrostatic discharges may cause damage to electronic components.
To a oid this, please perform the steps described on page 10 before you touch the CPCI-ETH2, in order to
discharge the static electricity from your body.
Qualified Personal
This documentation is directed exclusi ely towards personal qualified in control and automation engineering.
The installation and commissioning of the product may only be carried out by qualified personal, which is authorized to
put de ices, systems and electric circuits into operation according to the applicable national standards of safety
engineering.
Conformity
The CPCI-ETH2 is an industrial product and meets the demands of the EU regulations and EMC standards printed in the
conformity declaration at the end of this manual.
Warning: In a residential, commercial or light industrial en ironment the CPCI-ETH2 may cause radio interferences in
which case the user may be required to take adequate measures.
ata Safety
This de ice is equipped with an Ethernet or other interface which is suitable to establish a connection to data networks.
Depending on the software used on the de ice, these interfaces may allow attackers to compromise normal function, get
illegal access or cause damage.
esd does not take responsibility for any damage caused by the de ice if operated at any networks. It is the responsibility
of the de ice's user to take care that necessary safety precautions for the de ice's network interface are in place.
Intended Use
The intended use of the CPCI-ETH2 is the operation as Ethernet interface in a CompactPCI system.
The guarantee gi en by esd does not co er damages which result from improper use, usage not in accordance with
regulations or disregard of safety instructions and warnings.
● The CPCI-ETH2 is intended for installation in a CompactPCI system only.
● The operation of the CPCI-ETH2 in hazardous areas, or areas exposed to potentially explosi e materials is not
permitted.
● The operation of the CPCI-ETH2 for medical purposes is prohibited.
Service Note
The CPCI-ETH2 does not contain any parts that require maintenance by the user. The CPCI-ETH2 does not require any
manual configuration of the hardware.
isposal
De ices which ha e become defecti e in the long run ha e to be disposed in an appropriate way or ha e to be returned
to the manufacturer for proper disposal. Please, make a contribution to en ironmental protection.
Page 4 of 15 Hardware Manual • Doc. No.: I.2321.21 / Re . 1.1 CPCI-ETH2
