ESAB Retrofit Aristo Mig 4004i WeldCloud Manual de usuario

Aristo®

Instruction manual

0463 331 101 GB 20161123

Valid for: Mig 4004i Pulse serial no. 420-xxx-xxxx Mig 4004i

Pulse WeldCloud™ serial no. 550-xxx-xxxx

Mig 4004i Pulse,

Mig4004iPulseWeldCloud™

TABLE OF CONTENTS

0463 331 101 © ESAB AB 2016

1SAFETY ........................................................................................................... 4

1.1 Meaning of symbols ...................................................................................... 4

1.2 Safety precautions ........................................................................................ 4

2INTRODUCTION.............................................................................................. 7

2.1 Equipment ...................................................................................................... 7

3TECHNICAL DATA .......................................................................................... 8

4INSTALLATION................................................................................................ 10

4.1 Location.......................................................................................................... 10

4.2 Lifting instruction .......................................................................................... 10

4.3 Mains supply.................................................................................................. 11

5OPERATION .................................................................................................... 13

5.1 Connections and control devices ................................................................ 14

5.2 Symbols ......................................................................................................... 15

5.3 Connection of welding and return cable ..................................................... 15

5.4 Turning the power source on/off.................................................................. 15

5.5 Fan control ..................................................................................................... 15

5.6 Thermal protection ........................................................................................ 15

5.7 VRD (Voltage Reducing Device)................................................................... 15

5.8 Remote control unit....................................................................................... 15

5.9 MIG/MAG and self shielded cored wire welding......................................... 16

5.10 Arc voltage feedback .................................................................................... 16

6MAINTENANCE............................................................................................... 17

6.1 Inspection and cleaning................................................................................ 17

6.2 Welding torch................................................................................................. 17

7TROUBLESHOOTING ..................................................................................... 18

8ORDERING OF SPARE PARTS ...................................................................... 19

DIAGRAM ............................................................................................................... 20

ORDERING NUMBERS.......................................................................................... 22

SPARE PARTS LIST............................................................................................... 23

ACCESSORIES ...................................................................................................... 24

Rights reserved to alter specifications without notice.

1 SAFETY

0463 331 101 -4- © ESAB AB 2016

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of

life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and Safety

Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0463 331 101 -5- © ESAB AB 2016

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to EMF:

○ Route the electrode and work cables together on the same side of your

body. Secure them with tape when possible. Do not place your body

between the torch and work cables. Never coil the torch or work cable

around your body. Keep welding power source and cables as far away

from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0463 331 101 -6- © ESAB AB 2016

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be potential

difficulties in ensuring electromagnetic compatibility of class

A equipment in those locations, due to conducted as well

as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment and its implementation

in accordance with national law, electrical and/or electronic

equipment that has reached the end of its life must be

disposed of at a recycling facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved collection

stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0463 331 101 -7- © ESAB AB 2016

2 INTRODUCTION

The power sources Mig 4004i Pulse and Mig 4004i Pulse WeldCloud™ are intended for

MIG/MAG welding with pulsed current.

The Mig 4004i Pulse WeldCloud™ is provided with a top mounted control box which

enables wireless monitoring via a puck antenna.

The power sources are intended for use with the wire feed unit Aristo® Feed 3004/4804 or

Aristo® YardFeed 2000 and the cooling unit COOL 1. Aristo® Feed 3004/4804 is available

with two operational solutions, the Aristo® U6 panel and the Aristo® U82pendant. Aristo®

YardFeed 2000 is available with the Aristo® U6 panel.

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of

this manual.

2.1 Equipment

The power sources are supplied with:

• 5 m return cable with earth clamp

• 5 m mains cable with 32 Amp connector

• instruction manual for the welding power source

• Quick start guide WeldCloud™, only for Mig 4004i Pulse WeldCloud™

For Mig 4004i Pulse WeldCloud™, see the separate manual Quick start guide WeldCloud™

for a description how to install WeldCloud™.

For WeldCloud™ information, see

• Service manual W82, Retrofit Mig 4004i WeldCloud™, WeldCloud™ Mobile,

(0740800203)

• Instruction manual WeldCloud™ (0463 450 *)

3 TECHNICAL DATA

0463 331 101 -8- © ESAB AB 2016

3 TECHNICAL DATA

Mig 4004i Pulse / Mig 4004i Pulse WeldCloud™

Mains voltage 380-440 V, +/- 10%, 3~ 50/60 Hz

Mains supply Sscmin 1.8 MVA

Primary current Imax 28 A

No-load power Mig 4004i Pulse: 40 W

Mig 4004i Pulse WeldCloud™: 42 W

Setting range (DC)

MIG/MAG 16 A / 15 V - 400 A / 34 V

MMA 16A/21V-400A/36V

TIG 4A/10V-400A/34V

Permissible load at MIG/MAG

60 % duty cycle 400 A / 34.0 V

100% duty cycle 300 A / 29.0 V

Permissible load at MMA

60 % duty cycle 400 A / 36.0 V

100% duty cycle 300 A / 32.0 V

Permissible load at TIG

60 % duty cycle 400 A / 26.0 V

100% duty cycle 300 A / 22.0 V

Power factor at maximum current 0.94

Efficiency at maximum current 88 %

Open circuit voltage

VRD function inactive1) 55V

VRD function active1) <35V

Operating temperature -10 to +40°C

Transport temperature -20 to +55°C

Constant sound pressure when

idling

<70 dB(A)

Dimensions l×w×h Mig 4004i Pulse: 610×250×445 mm

(24.0x9.8x17.5in.)

Mig 4004i Pulse WeldCloud™: 610×250×515mm

(24.0x9.8x20.3in.)

Weight Mig 4004i Pulse: 44.5kg (98lb)

Mig 4004i Pulse WeldCloud™: 47.9kg (105lb)

Insulation class H

Enclosure class IP23

Application classification

1) The VRD function is explained in the instruction manual for the control panel.

Mains supply, Ssc min

Minimum short circuit power on the network in accordance with IEC 61000-3-12.

3 TECHNICAL DATA

0463 331 101 -9- © ESAB AB 2016

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or

cut at a certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

4 INSTALLATION

0463 331 101 - 10 - © ESAB AB 2016

4 INSTALLATION

The installation must be carried out by a professional.

CAUTION!

This product is intended for industrial use. In a domestic environment this product

may cause radio interference. It is the user's responsibility to take adequate

precautions.

4.1 Location

Position the welding power source in such way that its cooling air inlets and outlets are not

obstructed.

For Mig 4004i Pulse WeldCloud™, make sure the antenna on the top box is not covered or

blocked.

4.2 Lifting instruction

Otros manuales para Retrofit Aristo Mig 4004i WeldCloud

Tabla de contenidos

Otros manuales de Sistema de soldadura de ESAB

ESAB

ESAB Caddy Professional 250 Manual de usuario

ESAB

ESAB PT-27 Manual de usuario

ESAB

ESAB Pipeweld Orbiter Manual de usuario

ESAB

ESAB Precision Plasmarc EPP-600 Manual de usuario

ESAB

ESAB ST-21 Manual de usuario

ESAB

ESAB HandyPlasma 550 Guía de configuración

ESAB

ESAB Caddy Tig 1500i VRD Manual de usuario

ESAB

ESAB Cutmaster 60 Manual de usuario

ESAB

ESAB A6 Mastertrac Tandem Manual de usuario

ESAB

ESAB Rogue ES 180i Manual de usuario

ESAB

ESAB Warrior Feed 304 Manual de usuario

ESAB

ESAB Aristo RoboFeed 3004w Manual de usuario

ESAB

ESAB Aristo WeldCloud Mig U5000i Manual de usuario

ESAB

ESAB EAS IV Manual de usuario

ESAB

ESAB 653 cvcc Manual de referencia

ESAB

ESAB SR-B 9 Manual de usuario

ESAB

ESAB 100i Manual de usuario

ESAB

ESAB ESP-200 Manual de usuario

ESAB

ESAB CoolMidi 1800 Manual de usuario

ESAB

ESAB PT-26 Manual de usuario

ESAB

ESAB Aristo Mig 5000i Manual de usuario

ESAB

ESAB Origo Mig 4002cw Manual de usuario

ESAB

ESAB PT-36 Manual de usuario

ESAB

ESAB Origo Tig 3000i Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario