Ericsson GE FMD LBI-38609A Manual de usuario

TABLE OF CONTENTS

Page

SAFETY INFORMATION . . . . . . . . . . . . . . . . 3

INTRODUCTION . . . . . . . . . . . . . . . . . . . . 4

CONTROLS, INDICATORS, AND DISPLAYS . . . . . 4

Controls . . . . . . . . . . . . . . . . . . . . . . 4

Indicators . . . . . . . . . . . . . . . . . . . . . . 6

Keypad LEDs . . . . . . . . . . . . . . . . . . . 7

Displays . . . . . . . . . . . . . . . . . . . . . . 7

ALERT TONES . . . . . . . . . . . . . . . . . . . . . 9

OPERATING NOMENCLATURE . . . . . . . . . . . 10

OPERATING THE RADIO . . . . . . . . . . . . . . . 12

Turning The Radio On . . . . . . . . . . . . . . . 12

Selecting System/Group/Channel . . . . . . . . . 12

Adjusting Squelch (Conventional) . . . . . . . . . 13

Adjusting Backlight Level . . . . . . . . . . . . . 13

TRUNKED OPERATION . . . . . . . . . . . . . . . . 14

Receiving A Trunked Dispatch Call . . . . . . . . 14

Placing A Trunked Dispatch Ca1l . . . . . . . . . 14

CONVENTIONAL MODE OPERATION . . . . . . . . 15

Receiving A Call . . . . . . . . . . . . . . . . . . 15

Sending A Message . . . . . . . . . . . . . . . . 15

CONVENTIONAL FAILSOFT OPERATION . . . . . . 15

EMERGENCY OPERATION . . . . . . . . . . . . . . 16

Receiving An Emergency Message . . . . . . . . 16

Sending An Emergency Message . . . . . . . . . 16

Clearing An Emergency . . . . . . . . . . . . . . 17

SPECIAL CALLS . . . . . . . . . . . . . . . . . . . . 17

Placing A Telephone Interconnect Call . . . . . . 17

Receiving A Telephone Interconnect Call . . . . . 18

Placing An Individual Call . . . . . . . . . . . . . 18

Receiving An Individual Call . . . . . . . . . . . . 19

GROUP SCAN OPERATION . . . . . . . . . . . . . 19

Adding/Deleting To/From Scan . . . . . . . . . . 19

Starting Or Stopping Scan . . . . . . . . . . . . . 20

2nd SWITCH . . . . . . . . . . . . . . . . . . . . . . 20

EMER SWITCH . . . . . . . . . . . . . . . . . . . . 21

KEYPAD FUNCTIONS . . . . . . . . . . . . . . . . . 21

Primary Keypad (Assume User Options) . . . . . 21

Alternate Keypad (Assume Status Operation) . . . 23

DTMF Keypad Operation . . . . . . . . . . . . . 23

MOBILE DATA . . . . . . . . . . . . . . . . . . . . . 24

OPERATING PROCEDURES . . . . . . . . . . . . . 25

OPERATING TIPS . . . . . . . . . . . . . . . . . . . 26

SAFETY INFORMATION

The operator of any mobile should be aware of certain hazards

common to the operation of vehicular radio transmissions.

A list of the possible hazards are:

•

Explosive Atmospheres

Just as it is dangerous to fuel a vehicle with the motor running,

be sure to turn the radio off while fueling the vehicle. Do not

carry containers of fuel in the trunkof the vehicle when the radio

is mounted in the trunk.

•

Interference To Vehicular Electronic Systems

Electronic fuel injection systems, electronic anti-skid breaking

systems, electronic cruise control systems, etc., are typical of

the types of electronic devices that may malfunction due to the

lack of protection from radio frequency energy present when

transmitting. Ifthevehiclecontainssuch equipment,consultthe

dealer for the make of vehicle and enlist his aid in determining

if such electronic circuits perform normally when the radio is

transmitting.

•

Dynamite Blasting Caps

Dynamite blasting caps may be caused to explode by operating

a radio within 500 feet of the blasting caps. Always obey the

"Turn Off Two Way Radio" signs posted where dynamite is

being used. When transporting blasting caps in your vehicle:

a. Carry the blasting caps in a closed metal box with a soft

lining.

b. Leave the radio OFFwhenever the blasting caps are being

put into or removed from the vehicle.

•

Radio Frequency Energy

To prevent burns or related physical injury from radio frequency

energy, do not operate the transmitter when anyone outside of

the vehicle is within two feet of the antenna.

INTRODUCTION

The Ericsson GE FMD mobile radio is asynthesized radio that uses

microcomputer technology to provide high reliability and performance.

The radio is designed to provide mobile dispatch service in both

trunked and conventional operation.

The FMD consists of a radio assembly and control unit in a single

housing. The control unit may be optionally remote mounted. The

control unit is equipped with an alphanumeric display and switches for

control of the radio. The display and switch locations are backlighted

for night time use.

The FMD is PC Programmable to meet the specific needs of your

communications system. This manual provides information on the

features and operating procedures for your radio. There may be

descriptions for features which are not programmed on your particular

radio.

CONTROLS, INDICATORS, AND DISPLAYS

The FMD System radio contains twenty four switches, an eight

character alphanumeric display, nine indicators, and twelve LEDs. In

addition, there are times when partof the eight character display willbe

used to display the radio status.

A layout of the FMD front panel is shown in Figure 1.

CONTROLS

PWR

Momentary switch. Press once to turn on the radio.

Push again to turn off the radio.

VOLUME

Twomomentary switches (auto ramping).

VOLUMEUP

and

VOLUMEDOWN

. Beepsareheardwhilestep-ping

the volume when no call is in process. Hold the switch

(up or down) to auto ramp the volume.

SYSTEM

Two momentary switches (auto ramping). The

SYS-

TEM UP

and

SYSTEM DOWN

switches are used to

select system changes. The alphanumeric name of the

system will appear without changing systems the first

timeeither

SYSTEM

switch is pressed. (Note: the radio

may be programmed with wrap around on the system

selection; this would allow the radio to switch from the

highest to lowest system with one change instead of

wrapping all the way through the list).

GROUP

Two momentary switches (auto ramping). The

GROUP

and

GROUP DOWN

switches are used to select the

current group/channel selection. (See wrap around

note from SYSTEM.)

SPC

Momentary switch. The

SPC

(Special Call) switch is

used to enable special call mode if programmed in the

radio. Special Calls are used to place telephone inter-

connect calls and individually call other radios.

CLR

Momentary switch. The

CLR

switch is used to restore

the radio to normal group operation (e.g. exit Special

Call), monitor a conventional channel.

2nd

Momentary switch. The

2nd

switch is used to select the

functions of the DTMF keypad.

SCAN

Momentary switch. The

SCAN

switch is used to toggle

scan on and off. When on, the SCAN indicator in the

display will be on (note: The radio may be programmed

to disable scan when the microphone is off hook. If so

programmed, the radio will not scan when the micro-

phone is off hook, but SCAN remains on indicating the

state you have selected for normal operation.) The

SCAN

switch is also used in conjunction with the

GROUP

Up and Down switches to perform the Add and

Delete functions.

EMER

Momentary switch. The EMER switch may be pro-

grammedto send anEmergency messageand/orselect

a home group/channel.

INDICATORS

ON indicates the radio is transmitting.

BSY

Lights when a group is active (trunked system) or when a chan

nel is busy (conventional system). Flashes when a callis queued

on a trunked system.

SCAN

ON indicates that the user has enabled the Scan function.

S 1 2

Priority level for Scan:

indicates that the displayed

group/channel is enabled for scan.

indicates that the conven

tional channel is set for priority 2.

indicates that the conven

tional channel is set for priority 1.

ON indicates that the radio cannot locate a trunked

system. This indicates that the radio is not functional for

voice or data communications. FLASHING indicates

that the radio is operating in trunked failsoft mode and

some of the features of the system may not be available

for use (e.g. Telephone Interconnect).

PVT

ON indicates that the radio has been set to transmit in

Voice Guard encrypted mode (Note: must have a Voice

Guard module attached to the radio for this indicator to

work).

EMER

ON indicates that the radio has declared an Emergency

on the system (may beprogrammed to notdisplay when

declaring emergencies). FLASHING indicates that an-

other radio on the displayed group has declared an

emergency.

KEYPAD LEDs

The twelve switch keypad is a programmable keypad with multiple

layers of functions: DTMF keypad, User Programmable Options, and

Status operation. These functions are accessed via Special Call or the

2nd key. The Primary keypad (typically the User Programmable Op-

tions) is the one which uses the twelve LEDs (one above each switch).

The following functions will cause the corresponding LED above its key

to light: External Alarm Active, Mobile Data disabled, External Speaker

selected, Message mode, Public Address active, or Voice Guard Pri-

vate mode.

DISPLAYS

The radio is capable of displaying status messages in the alpha

display. Some of these messages will use the entire display while

others will use two characters. When the short message is displayed

it may be on the right or left of the display. It is separated from the

normal information with an indicator such as an asterisk ("*").

Full Length Indicators

**INDV** Displayedwhenyourunitreceives anindividualcallfrom

another unit.

ID ##### If programmed, displayed when your unit receives an

individual call where ##### is the unit id of the calling

radio (Note: If the ID is in your Special Call list, it may

show an 8 character name instead of the number).

GR ##### If programmed, displayed when acall is received to your

selected group where ##### is the unit ID of the calling

radio (Note: If the ID is in your Special Call list, it may

show an 8 character name instead of the number).

PHN CALL Displayed when your radio receives a telephone call

from the trunked system.

DATACALL Displayed when your radio is involved in a data call.

*NO DATA Displayed when your radio is in the data disabled state.

ALL CALL Displayed when receiving a System wide call.

*AGENCY* Displayed when receiving an Agency Call.

*FLEET* Displayed when receiving a Fleet Call.

PRIMARY Displayed when using 2nd to select primary keypad

operation.

ALTRNATE Displayed when using 2nd to select alternate keypad

operation.

KEYPAD Displayed when using 2nd to select DTMF from the

keypad in conventional mode or in Special Call mode.

Abbreviated Indicators

C Displayedwhenanindividualcallhasbeenreceivedand

not answered. By selecting Special Call, the call can be

recalled for return at a later time (Note: the call is not

saved through a power cycle and the ID is cleared by

pressing the CLR switch).

ALERT TONES

The FMD mobile generates a number of alert tones to indicate its

current state. These tones are described below:

CALL ORIGINATE

A short tone is sounded whenever you key the microphone Push-

To-Talk (PTT) switch and the radio has acquired a channel. This tone

indicates that you may proceed to talk (both conventional and trunked

operation).

CALL QUEUED (Trunked Operation Only)

If your hear one short, high pitched beep after you key the micro-

phone, this indicates that the system has placed your request in a

queue. The tones are sounded at both your transmitting unit and your

receiving unit(s), indicating to the user on the receiving end that they

will receive a call shortly. If you should unkey the microphone while in

queue, your radio will autokey when a channel becomes available

(Automatically key (push-to-talk), see AUTOKEY below).

AUTOKEY (Trunked Operation Only)

When you key the microphone to place a call on the system and

release the PTT switch before getting to the channel (e.g. a queued

call), the radio will automatically key on the channel when it gets the

assignment. The radio will generate a long beep and hold the transmit-

ter keyed for two seconds. Press the PTT switch to keep the channel

and send your message before this two second timeout has expired.

SYSTEM BUSY (Trunked Operation Only)

If you key the microphone and hear three short, medium pitched

beeps, this indicates that the receiving party is already on the system

or the system is busy and its queue is full. You must rekey later to

access the system.

CALL DENIED (Trunked Operation Only)

If you hear a single low pitched tone when you key the microphone,

your request has been denied by the system. This will happen if you

are an invalid user or if you are requesting an unavailable service.

OUT OF RANGE/SYSTEM INOPERATIVE (Trunked Operation

Only)

If you hear a single low pitched tone immediately after you key the

microphone, this indicates your mobile unit is out of range of the

repeater. Your radio will try to place the call for a short period after the

initial attempt. The radio willgenerate a second low pitched beep when

it gives up trying to place the call. If you hear these beeps when you

know you are in calling range, this indicates that the system is off the

air, or that your mobile unit needs servicing. When the mobile is out of

range, the NC indicator will be displayed.

CARRIER CONTROL TIMER

The Carrier Control Timer alert is a low pitched tone you will hear

whenever you have kept the PTT switch continuously pressed for a

preprogrammed length of time. The transmitter will shut down when

the steady low pitched tone starts, interrupting communications. When

on a trunked system, the FMD will generate short beeps prior to

unkeying to alert you that the transmission is about to be terminated.

To maintain communications, release and re-key themicrophone. This

resets the timer and turns the transmitter back on. The CCTis a built-in

precaution against inadvertent use of the system.

OPERATING NOMENCLATURE

CONVENTIONAL OPERATION

All radios on a conventional system operate in one of two modes:

repeatedortalk-around. Talk-around(alsoreferredtoas"directmode")

provides a direct radio-to-radio short-range communications link. It is

intended to maintain communications outside of the main system

coverage area. Trunked features (such as call queueing and system

scan) are not available in conventional mode.

TRUNKED OPERATION

Trunked operation refers to the use of a set of radio frequency

channels by multiple user groups. By using high speed digital signal-

ling, users may place and receive calls to single or multiple users

without being monitored by other users (or groups) on the system.

Tabla de contenidos

Otros manuales de Radio de Ericsson GE

Ericsson GE

Ericsson GE EDACS FMD Manual de usuario

Ericsson GE

Ericsson GE LBI-38378C Manual de usuario

Ericsson GE

Ericsson GE LBI-31932E Manual de usuario

Ericsson GE

Ericsson GE MTD SERIES Manual de usuario

Ericsson GE

Ericsson GE MDS Manual de usuario

Ericsson GE

Ericsson GE MDX Manual de usuario

Ericsson GE

Ericsson GE MDX/ORION Manual de usuario

Manuales populares de Radio de otras marcas

EisSound

EisSound KBSound iSelect Manual de usuario

Midland

Midland 1001LWX Manual de usuario

Konig

Konig HAV-SR41 Manual de usuario

Roberts

Roberts exprssion Manual de usuario

VDigi

VDigi DD3.0 Manual de usuario

Radio Shack

Radio Shack 21-1863 Manual de usuario

Roberts

Roberts Stream 207 Manual de usuario

Sony

Sony Walkman SRF-M97 Manual de usuario

Stanley

Stanley FatMax FMC770 Manual de usuario

auna

auna DAB-Radio 10026947 Manual de usuario

SOUNDMASTER

SOUNDMASTER UR190 Manual de usuario

HYT

HYT TC-320 Manual de usuario

auna multimedia

auna multimedia Yellowstone 10026851 Manual de usuario

B-Tech

B-Tech GMRS-V2 Manual de usuario

Weierwei

Weierwei VEV-V8 Manual de usuario

SOUNDMASTER

SOUNDMASTER DAB750 Manual de usuario

Telefunken

Telefunken TF-1505 Manual de usuario

Makita

Makita LXRM03 Manual de usuario