Ergotron WorkFit-P Manual de usuario
1 of 9
888-45-307-G-01 rev. F • 11/13
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイ ド : 日本語
用户指南 : 汉语
For the latest User Installation Guide please visit: www.ergotron.com
ENGLISH
For the latest User Installation Guide please visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
2 of 9
888-45-307-G-01 rev. F • 11/13
WARNING
ENGLISH
Important! You will need to adjust this product after installation is complete. Make sure all your
equipment is properly installed on the product before attempting adjustments. This product should move
smoothly and easily through the full range of motion and stay where you set it. If movements are too
easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to
create smooth and easy movements. Depending on your product and the adjustment, it may take many
turns to notice a difference.Any time equipment is added or removed from this product, resulting in a
change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and
optimum operation.
CAUTION! Max weight 10 lbs (4.5 kg). Do not exceed maximum listed weight capacity.
Serious injury or property damage may occur!
Warning! Do not move arm until Lock is installed in the next step. Failure to follow these instructions may result in your arm
coming o the pole base and causing equipment damage and/or personal injury.
Warning! Remove arm from pole base before removing clamp or grommet hole mount from desk. Failure to follow these
instructions may result in the arm falling over causing equipment damage and/or personal injury.
Warning! Do not use with LCD on platform. Failure to follow these instructions will create an
unstable situation and may result in equipment damage and/or personal injury.
WARNING! Stored Energy Hazard:The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!
3 of 9
888-45-307-G-01 rev. F • 11/13
AB C D
1
2
3
4
5mm
13mm
4 mm
2.5 mm
M6 x 14mm
1/4”
8mm
ENGLISH
Components
Tools Needed
Optional for Pan Adjustment
4 of 9
888-45-307-G-01 rev. F • 11/13
1
4 mm
1x
1x
1x
4 mm
b
c
d
a
1x
1/4”
8mm
0.5"-2.5"
(13-64mm)
0.78"-2.56" (20-65mm)
0.78"-1.38" (20-35mm) 1.18"-2.56" (30-65mm)
ENGLISH
Set-up Steps
Warning: Because mounting surface materials can vary widely, it
is imperative that you make sure mounting surface is strong enough to
handle mounted product and equipment.
CAUTION: Bolt must be
centered in hole.
CLAMP GROMMET HOLE
DESK THICKNESS
5 of 9
888-45-307-G-01 rev. F • 11/13
2
31x 1x
4 mm
ab c
8
1x
ENGLISH
Set-up Steps
Warning! Do not move arm until Lock is
installed in the next step. Failure to follow
these instructions may result in your arm
coming o the pole base and causing
equipment damage and/or personal injury.
The height of the Arms Stop can be moved up or
down on pole. If you would like to move the Arm
Stop, see page 8 for instructions.
WARNING: Arm must be removed from pole
before moving Arm Stop. Failure to remove arm
may result in equipment damage and/or personal
injury.
Arms Stop Warning! When removing arm from desk,
remove arm from pole base before removing
clamp or grommet hole mount from desk.
Failure to follow these instructions may result
in the arm falling over causing equipment
damage and/or personal injury.
6 of 9
888-45-307-G-01 rev. F • 11/13
4
5
2x
M6 x 14mm
4 mm
a
b
c
d
ENGLISH
NOTE: These screws insert at an angle.
7 of 9
888-45-307-G-01 rev. F • 11/13
6
12
a
5mm
WARNING
ENGLISH
Increase Lift Strength
If the mounted weight is too heavy or this product does not
stay up when raised, then you'll need to increase Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or this product does not stay
down when lowered, then you'll need to decrease Lift Strength:
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all
your equipment is properly installed on the product before attempting adjustments. This
product should move smoothly and easily through the full range of motion and stay where
you set it. If movements are too easy or difficult or if product does not stay in desired
positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a
difference.Any time equipment is added or removed from this product, resulting in a
change in the weight of the mounted load, you should repeat these adjustment steps to
ensure safe and optimum operation.
WARNING! Stored Energy Hazard:The arm mechanism is under
tension and will move up rapidly, on its own, as soon as attached
equipment is removed. For this reason, DO NOT remove equipment
unless the arm has been moved to the highest position! Failure to
follow this instruction may result in serious personal injury and/or
equipment damage!
8 of 9
888-45-307-G-01 rev. F • 11/13
b
c
13mm
2.5 mm
Arms Stop
ENGLISH
Adjustment Step
Increase Friction
If this product moves too easily from
side-to-side, then you'll need to
increase friction:
Decrease Friction
If this product is too difficult to move
from side-to-side, then you'll need to
decrease friction:
The height of the Arms Stop can be moved up or down on pole.
WARNING: Arm must be removed from pole before moving Arm Stop. Failure to remove arm
may result in equipment damage and/or personal injury.
79 Overseas Drive Noble Park, VIC 3174 Australia
T: (+61) 03 9020 2098 | Freecall: 1800 615 666 (within Australia) | F: (+61) 03 9020 2092
9 of 9
888-45-307-G-01 rev. F • 11/13
20”
360˚ 180˚
ENGLISH
NOTE: When contacting customer
service, reference the serial number.
Learn more about ergonomic computer use at:
www.computingcomfort.org
Set Your Workstation to Work For YOU!
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists at.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain at.
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
Features & Specifications
Otros manuales para WorkFit-P
5
Tabla de contenidos
Otros manuales de De oficina de Ergotron
Ergotron
Ergotron WORKFIT Manual de usuario
Ergotron
Ergotron 97-583-009 Manual de usuario
Ergotron
Ergotron StyleView Manual de usuario
Ergotron
Ergotron WorkFit-S Manual de usuario
Ergotron
Ergotron StyleView Manual de usuario
Ergotron
Ergotron Command Post Manual de usuario
Ergotron
Ergotron WorkFit-Z mini Manual de usuario
Ergotron
Ergotron WorkFit-S Manual de usuario
Ergotron
Ergotron StyleView Manual de usuario
Ergotron
Ergotron 48 Unit Management Cart Manual de usuario
Ergotron
Ergotron STYLEVIEW Series Manual de usuario
Ergotron
Ergotron Desktop 16 Manual de usuario
Ergotron
Ergotron WorkFit-P Manual de usuario
Ergotron
Ergotron StyleView Manual de usuario
Ergotron
Ergotron WorkFit-P Manual de usuario
Ergotron
Ergotron WorkFit-A, Single LCD Mount, LD Manual de usuario
Ergotron
Ergotron WorkFit-P Manual de usuario
Ergotron
Ergotron TeachWell Mobile Digital WorkSpace Manual de usuario
Ergotron
Ergotron Steve's Station Advanced Manual de usuario
Ergotron
Ergotron StyleView VL Enclosure Guía de solución de problemas
