Erduro BTS ENGINEERING Fluid Solutions BTKF-I Manual de usuario

SINGLE STAGE

USER MANUAL

BTKF-I

https://prom-nasos.pro

https://bts.net.ua https://

prom-nasos.com.ua

+38 095 656-37-57,

+38 067 360-71-01,

+38 063 362-12-31,

[email protected]

- You should absolutely obey the followng safety nstructons.

- Never touch the pump and ppes havng temperature more than 80 ºC. Necessary

precautons should be taken for warnng users. (E.g Warnng sgns and sgnboards )

Never operate pump n reverse

drecton.

- Do not walk over pump pr ppes whch are connected to pump.

- Any operaton whch wll be done n pump should be performed by at least two

staﬀs.

- No works should certanly be done over wthout stoppng pump group.

Power comng to pumps should be oﬀ and you should be sure that t wll not operate

agan before you make any work

- Absolutely nstall the safety guards whch were dsmounted before after work n

pump has ﬁnshed.

- Tensons and crcks n ppe system absolutely should not reach to pump.

Do not make any operaton whle pump and ppes whch are connected to pump are

under pressure.

- Cloths of personnel who wll work over should be sutable and/or they should use

safety equpments.

Never do any operatons when pump s stll hot.

- Electrcal connecton related wth pump and auxlary equpments should be sutable

wth local rules and made by authorzed personnel.

- Operate pump wth only specﬁed condtons.

- Do not nsert your hand and ﬁngers nto holes and spaces over pump body.

- Be always careful whle workng wth pumps dschargng hazardous lquds.

SAFETY INSTRUCTIONS

Fl uid

So lut ion s

BTKF-I Seres Pumps are centrfugal pumps havng horzontal shaft, separable radal

body, are sngle staged, scroll cased has closed mpellor, and can be connected to

straght ppe.

Usage Areas of Motor Water Pump

Pumps are sutable for dschargng lquds whch are low vscose, whose flow

temperature s up to 110ºC and whch are clean or a lttle drty. (Max20mg/dm³) . In

addton to others; man applcaton areas are:

- Heatng and Coolng Systems

- Water Supply

- Fre Extngushng Plants

- Water Supply and Crculaton Systems n Industral Plants

Explanaton of Pump Codes

BTKF-I 40/200

Pump Type

Rated Dameter of Dscharge Flange (DN-mm)

Number of Stages(pece)

Techncal nformaton

Speed : Up to3600 d/d rpm

Dscharge Flange :DN40 …DN200

Sucton

And Dscharge

Flange : TS EN 1092-2,EN 1092-2-EQV /PN16

Operatonal Temperature

:-10ºC…110ºC

Ambent Temperature (Maxmum) :+40ºC

Body Pressure :16 Bars

Isolaton Class

Protecton Class

:IP55

Motor Connecton :3 Phase-380 V-50 Hz

Fl uid

So lut ion s

BTKF-1 SERİES PUMPS

Fl uid

So lut ion s

- Check whether all materals n delvery lst are sent. .

- If there s damage durng shppng please notfy ERDURO Shppng Department

and Transportaton company.

If there are mssng materals, mmedately nform ERDURO Shppng Department.

Check whether packagng s damaged durng transportaton.

Please carefully take out packaged pump and accessores (f any). Check whether

they are damaged durng transportaton.

General warnngs.

Absolutely obey the followng rules durng transportaton.

-. Use proper wooden crane, forklft, or hostng mechansms For unloadng or

loadng wooden cases, packages, boxes and palettes dependng on ther weght and

volume.

Wear gloves, hard tp shoes and helmet durng carryng works.

Never stay under hostng mechansm whle loadng or unloadng pumps.

Pump and Motor Group Loadng/Unloadng

Before loadng/unloadng pump group please determned the followng propertes.

- Please ﬁnd the lftng ponts.

- Please consder total weght and centre of gravty.

Please consder the packagng external dmensons

Durng loadng/unloadng make acceleratng and brakng operatons as t shall not

cause any damage for workng personnel.

- Load lftng capacty should be sutable wth pump and pump group weght.

- You should never stay under or near lfted load.

SHIPPING OF PUMPS

CARRYING

Fl uid

So lut ion s

- Pump should be hosted as t s ndcated n Fgure 1 -1 and Fgure 1 -2 for not

causng any damage n pumps. Motor hangng rng should absolutely

not be used

whle lftng complete group.

- Load should be kept n lfted poston more than requred tme.

- Pump and pump group should always be lfted and carred n horzontal poston

Fgure 1 Pump carryng

STORAGE

- If pump group s not mmedately nstalled, t should be stored n a place whch s

clean dry and does not nclude freezng and exploson rsk.

If pump bearng are type whch should be greased, they should be extra greased for

preventng entry of mosture to bearngs around shaft

- Pump should be protected from mosture, dust, drt and foregn objects by coverng

wth sutable materal.

- Pump shaft should be rotated a few turns (e.g once a week) for preventng pttng

around pump bearng surfaces and jammng of shaft.

INSTALLATION

Installaton of pump to ts place and connecton setup

and balance should only be

done by expert personnel. Faled nstallaton and pump ground may cause falures.

Ths stuatons are not covered wth warranty

Before nstallng the pump n ts place,

Sucton and dscharge ﬂanges should properly be cleaned.

ATTENTION- Pump should be nstalled n a locaton where there s not exploson and

frost hazard and has good ar condtonng.

- There should be enough area around pump for reachng pump easly, for

mantenance and there should be enough space and heght to lft the pump f

necessary.

-Pump sucton ppe should be as short as possble.

If BTKF-I pumps are nstalled over a ppe whch s well supported or over ground by

means of base plate.

-BTKF-I pumps can be mounted to ﬂat ppes vertcally or horzontally.

Flow can be from upwards to downwards or reverse n pumps whch are connected

vertcally. (Provded that pump ﬂow drecton has been connected correct)

Motor axs can be n vertcal or horzontal poston n pumps whch are connected to

horzontal ppe motor should never reman below the horzontal plane.

Pump whch s nstalled over a pump ground can be mounted to a ﬂexble ppe by

means of base plate.

ATTENTION:- You should be carefully work at pump nstallaton ground preparaton

and nstallaton of pump group nto ts place. Incorrect and careless nstallaton

causes early wearng of pump parts and falures.

- Pump ground should be so heavy to absorb vbratons and sturdy to prevent bends

and adjustments defects. Ground concrete should completely be soldﬁed,

completed ts plug tme and proper stud bolts are placed n pump frame ﬁxng holes

and proper ﬁxng lugs should be placed for usng n makng connectons wth weldng.

Concrete and plate upper surface should be horzontal and very smooth.

-Place the pump group over concrete ground and put or remove steel wedges under

frame and adjust the ﬂanges. Provde that pump shaft completely n horzontal

poston.

-Tghten the anchorage stud bolts properly.

Installaton of Ppe Lne Installaton

-Nomnal dameter of pump dscharge and sucton pumps are not an ndcator for

correct dameters for dscharge and sucton ppes.

- It should be controlled that crcks and stresses and ppe weght do not eﬀect pump.

GENERAL

Fl uid

So lut ion s

- Flow rates generally should not exceed 2m/s n sucton ppe and 3 m/s dscharge

ppe.

- Especally bottom backwater valve, slt trap,

ﬁlter and check valves and smlar

elements should be chosen to havng a larger passng area.

For ths reason, bolts of dscharge and sucton ﬂanges should be loosen and t

should be controlled whether ppe system exerts a stress over pump.

Ppes and accessores havng dameter less than pump openng dameter should

absolutely not be used.

Never use

pumps as a support pont or carrer for a ppe nstallaton.

- Ppe system should be supported from ponts whch are close to pump. Fgure 2.

- Proper expanson equpments should be used for preventng addtonal forces to

pump whch may occur because of expanson n systems whch operate n over

vbrant and hot lquds.

Hgh speeds cause decrease n pressure

whch wll cause cavtatons condtons

and excess frcton losses n dscharge ppe.

- Weldng burrs, metal partcles, whch may occur durng ppe equpment producton

sand, and oakum and smlar foregn objects may present nsde pump. Sucton and

dscharge ﬂanges should be closed wth gasket wthout hole for preventng those

materals enter nto pump durng nstallaton. At the end of nstallaton, all ppe parts

should be dsmounted, cleaned and dyed and nstalled agan. If drt retaned s used

at pump sucton lne, t should be removed and cleaned after ﬁrst few days of

operaton and nstalled agan.

Fgure 2

Fl uid

So lut ion s

Ppe connectons should be made by ﬂanges. Flanges gaskets should be produced

from sutable materal and should have sutable dmensons. Gaskets whch wll be

used between ﬂanges should be centered for not preventng water ﬂow.

Fgure 3

Sucton and Dscharge Ppe Connectons

- If pump s suppled from a tank whch s hgher than pump, there should be an

solaton valve n sucton ppe whose axs wll be n horzontal poston. Ths valve

should

be completely open whle pump s n operaton and should never be used as

ﬂow rate adjustment valve. (Attenton: Closng valve may cause pump operaton wth

cavtatons. )

Sucton ppe should absolutely be mpermeable and should not be arranged to

cause any ar wall. In ths case f a tank s suppled from a tank whch s hgher than

pump, (sucton hgh nstallaton) sucton ppe should be slghtly decreasng sloped

towards pump and suppled from a tank whch s lower than pump, sucton ppe

should be

slghtly ncreasng sloped towards pump.

Sharp bends should not be used, sudden drecton changes and cross secton

narrowng should be avoded and sucton ppe should be short as possble for

keepng pump frcton losses as low as possble. If there s need of cross secton

change n horzontal sucton ppe, an ntermedate eccentrc concal part whose ﬂat

type s at upper sde should be used.

-. If pump dschargng heght s more than 10 m or dschargng lne s very long, a

check valve should be placed over dschargng ppe between pump and solaton

valve for protectng pump aganst water mpulses and reverse ﬂows durng stop.

A control valve whch s close to pump should be connected for ﬂow rate and

dscharge heght adjustment.

If pump dschargng heght s more than 10 m or dschargng lne s very long, a

check valve should be placed over dschargng ppe between pump and solaton

valve for protectng pump aganst water mpulses and reverse ﬂows durng stop.

Fl uid

So lut ion s

d1: Sucon Opening Pressure

Meter Connecon

d2: Discharge Opening Pressure

Meter Connecon

By-Pass Valve Connecton

A by-pass valve should be places over dscharge ppe just after pump and before

adjustment valve or outlet ﬂange of pump f there s a case that pump wll operate n

condtons that pump dscharge valve s completely closed(that s wth zero ﬂow rate)

or almost closed (that s wth very small ﬂow rate). If such valve s not used and

pumps operates wth closed valve for a long tme, power whch s provded by motor

wll completely transform nto heat energy and pass nto dscharged lqud. Ths may

cause over heatng and abnormal falures n pump.

ELECTRICAL CONNECTIONS

- Electrcal connectons should be done by authorzed electrcans

Natonal nstructons, regulatons and nstructons of motor manufacturers should be

obeyed.

- Power cables should absolutely be nstalled as not

havng contact wth ppe

nstallaton, pump and motor body.

Motor shaft should be rotated by hand before makng electrcal condtons to control

whether t rotates easly.

It s recommended to use PTC(Passve Thermal Control-Thermstor) n motors.

However usage of those

depends on customer.

- Electrcal motors should be protected aganst overloadng by crcut breakers and/or

fuses. Crcut breakers and/or fuses should be selected wth respect to full load

values those are wrtten n nameplate on motor.

Fl uid

So lut ion s

Fl uid

So lut ion s

Compare and control voltage, ampere and frequency values whch are gven n

motor nameplate wth lne values.

Motor connecton scheme can be found n motor termnal box or n handbook.

- Motor electrcal connectons should be done accordng to local Electrcal

Regulatons and earthng connecton should absolutely be done.

Protecton class of motor body and control system cases n pump should be at least

EN 60529 IP 22. In addton to ths, protecton class of motor bodes and control

systems n pump group should be determned accordng to operatonal and

envronmental condtons.

Safety precautons whch are determned n "Safety Instructons" should be appled.

All power connectons should be dsconnected before startng to any work.

-However usage of those depends on customer. If PTC s used ends of those should

be connected to motor termnal box and later should be connected to PTC control

devce n motor control panel.

Motor connecton type changes accordng to motor mans power and connecton

type. Necessary connecton types of jumpers n termnal box are dsplayed n Table 1

and Scheme 1a -1b and 1c

Scheme 1a Scheme 1b Scheme 1c

Start Type Motor Power

PN<4kW

Motor Power

PN >4kW

Mans Power

3~400V

Mans Power

3~400V

Drect

Y-connecton (1b) Δ-connecton (1a)

Y/ Δ Star Delta Impossble

Remove Jumpers (1c)

Table 1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario