Equinox Systems Kaleido EQLED85 Manual de usuario

Order code: EQLED85

Kaleido

User Manual

www.prolight.co.uk Kaleido User Manual

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.

• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.

• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary

fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.

• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand

thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.

Donotendangeryourownsafetyandthesafetyofothers!

Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.

• Neverletthepowercablecomeintocontactwithother

cables.Handlethepowercableandallmainsvoltage

connectionswithparticularcaution!

• Neverremovewarningorinformativelabelsfromtheunit.

• Donotopentheequipmentanddonotmodifytheunit.

• Donotconnectthisequipmenttoadimmerpack.

• Donotswitchtheequipmentonandoffinshortintervals,

asthiswillreducethesystem’slife.

• Onlyusetheequipmentindoors.

• Donotexposetoammablesources,liquidsorgases.

• Alwaysdisconnectthepowerfromthemainswhen

equipmentisnotinuseorbeforecleaning!Onlyhandle

thepower-cablebytheplug.Neverpullouttheplugby

pullingthepower-cable.

• Makesurethattheavailablevoltageisbetween

100~240V,50/60Hz.

• Makesurethatthepowercableisnevercrimpedor

damaged.Checktheequipmentandthepowercable

periodically.

• Iftheequipmentisdroppedordamaged,disconnectthe

mainspowersupplyimmediatelyandhaveaqualied

engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic

temperatureuctuation(e.g.aftertransportation),

donotconnectpowerorswitchitonimmediately.

Thearisingcondensationmightdamagetheequipment.

Leavetheequipmentswitchedoffuntilithasreached

roomtemperature.

• Ifyourproductfailstofunctioncorrectly,stopuse

immediately.Packtheunitsecurely(preferablyinthe

originalpackingmaterial),andreturnittoyourProLight

dealerforservice.

• Onlyusefusesofsametypeandrating.

• Repairs,servicingandpowerconnectionmustonlybe

carriedoutbyaqualiedtechnician.THISUNITCONTAINS

NOUSERSERVICEABLEPARTS.

• WARRANTY:Oneyearfromdateofpurchase.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

www.prolight.co.uk Kaleido User Manual

Product overview & technical specications

TheKaleidoisaconstantlychangingdecorativeeffectthatprojectsavaryingdisplayofpsychedelicpatterns.Using

ahighpower60WLEDitsbrightoutputandrazorsharpimagesaddauniqueelementtoanyshow,venueorparty.

•1x60WwhiteLED

•3facetrotatingprism

•DMXchannels:4

•Auto,soundactiveandmaster/slavemodes

•0-100%dimming

•4pushbuttonmenuwithLEDdisplay

•IECinput/output

•3-pinXLRinput/output

•Fancooled

•Suppliedwithhangingbracket

Kaleido

Specications

Powerconsumption 85W

Powersupply 100~240V,50/60Hz

Fuse F3A250V

Dimensions 215x210x380mm

Weight 3.6kg

Ordercode EQLED85

215mm

210mm 380mm

www.prolight.co.uk Kaleido User Manual

01-Manualfocus

02-Hangingbracket

03-Safetyeye

04-Soundsensitivityknob

05-DMXoutput

06-DMXinput

07-IECpoweroutput

08-IECpowerinput

09-FuseF3A250V

10-Earthpoint

11-Fan

Inthebox:1 x xture,

1 x power cable &

1 x user manual

Technical specications

POWER IN:

100-240V~50/60Hz

FUSE: F3A 250V

POWER OUT

DMX IN

DMX OUT

SAFETY

EYE

SOUND

SENSITIVITY

www.prolight.co.uk

MIN MAX

www.prolight.co.uk Kaleido User Manual

Operating instructions

DMX mode:

OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes

tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthe

xtureandeachxtureindependently.

ToaccesstheDMXaddressmode,pressthe“MENU”buttononthefrontoftheunittoshowAddr

ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe

requiredDMXaddress.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Auto mode:

Toaccesstheautomode,pressthe“MENU”buttononthefrontoftheunittoshowAutoonthe

LEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstochooseoneofthe

3automodes.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Sound active mode:

Toaccessthesoundactivemode,pressthe“MENU”buttononthefrontoftheunittoshowSoun

ontheLEDdisplay.Nowpressthe“ENTER”buttontoconrmthesetting,andusethesoundsensitivity

knobtoadjustthesoundsensitivity.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

Master/slave mode:

Tosetthemasterunit,pressthe“MENU”buttonontherearofthemasterunittoselectyour

desiredprogram(soundactiveorauto).

Tosettheotherunitsinslavemode,pressthe“MENU”buttonontherearoftheunittoshowSLav

ontheLEDdisplayandpressthe“ENTER”buttontoconrmthesetting.Theunitswillnowrunin

sequencewiththemasterunit.

Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

4 channel mode:

Channel Value Function

CH1 000-255 Masterdimmer(0-100%)

CH2 000-249 Gobopatternselect

250-255 Constantgobopatternchange

CH3 000-255 Goborotationdirection

CH4 000-255

Goborotationspeed(fast-slow)

(Thisfunctionwillonlyworkwhen

channel3is0-9or250-255)

www.prolight.co.uk Kaleido User Manual

Setting the DMX address:

TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”

from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel

indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas

addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105

and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe

chainstartsat107.

DMX 512:

DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent

xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.

DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”

XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).

DMX linking:

DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether

andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.

ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest

cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe

DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein

aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda

DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,

nomatterwhereitislocatedintheDMXchain.

DATA cable (DMX cable) requirements (for DMX operation):

ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.

YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,

seeimagebelow.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

FurtherDMXcablescanbe

purchasedfromallgoodsound

andlightingsuppliersor

ProLightConceptsdealers.

Pleasequote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk Kaleido User Manual

Notice:

Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables

shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs

outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.

Special note:

Line termination:

Whenlongerrunsofcableareused,

youmayneedtouseaterminatoron

thelastunittoavoiderraticbehaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures

maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa

3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.

Terminationreducessignaltransmission

problemsandinterferance.itisalways

advisabletoconnectaDMXterminal,

(resistance120Ohm1/4W)betweenpin2

(DMX-)andpin3(DMX+)ofthelastxture.

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

www.prolight.co.uk Kaleido User Manual

WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof

withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe

environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother

typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.

Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir

localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally

saferecycling.

Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe

purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

Tabla de contenidos

Otros manuales de Equipo de iluminación de Equinox Systems

Equinox Systems

Equinox Systems Spectra Strobe Batten Manual de usuario

Equinox Systems

Equinox Systems Krypton EQLED21 Manual de usuario

Equinox Systems

Equinox Systems CONSTELLA Manual de usuario

Equinox Systems

Equinox Systems ATRIA Manual de usuario

Equinox Systems

Equinox Systems Fusion 150 Manual de usuario

Equinox Systems

Equinox Systems SIGMA EQLA09 Manual de usuario

Equinox Systems

Equinox Systems Eyebar Manual de usuario

Equinox Systems

Equinox Systems EQLED040 Manual de usuario

Equinox Systems

Equinox Systems Lexor Manual de usuario

Equinox Systems

Equinox Systems Interceptor MKII Manual de usuario

Equinox Systems

Equinox Systems Tri Power Batten MKII Manual de usuario

Equinox Systems

Equinox Systems EQLED008 Manual de usuario

Equinox Systems

Equinox Systems Explo Strobe EX-2500 Manual de usuario

Equinox Systems

Equinox Systems KAMIKAZE EQLA14 Manual de usuario

Equinox Systems

Equinox Systems EQLED65 Giga Bar System Manual de usuario

Equinox Systems

Equinox Systems MidiPar Tri Plus Manual de usuario

Equinox Systems

Equinox Systems PEGASUS II Manual de usuario

Equinox Systems

Equinox Systems XP 80W Manual de usuario

Equinox Systems

Equinox Systems Lighting strike STRO21 Manual de usuario

Equinox Systems

Equinox Systems Vortex Manual de usuario

Equinox Systems

Equinox Systems Swing Batten Manual de usuario

Equinox Systems

Equinox Systems 400W UV Cannon Manual de usuario

Equinox Systems

Equinox Systems Goboceptor Manual de usuario

Equinox Systems

Equinox Systems Comet EQLED29 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario