Equinox Systems MIRR22 Manual de usuario

Order code: MIRR22

DMX Heavy Duty 1 RPM

Mirror Ball Rotator

with Safety Eye

User Manual

www.prolight.co.uk DMX Mirror Ball Rotator User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage

and the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

This device is a mirror ball motor for turning mirror balls. The maximum load of the installation eyelet must never

be exceeded. The safety eyelet must never be used for loads.

When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture or dust.

There should not be any cables lying around. You endanger your own and the safety of others!

This device must never be operated or stockpiled in surroundings where water, rain, moisture or fog may harm the device.

Moisture or very high humidity can reduce the electrical insulation and lead to mortal electrical shocks.

The ambient temperature must always be between -5°C and +45°C. Keep away from direct insulation (particularly in cars)

and heaters. The relative humidity must not exceed 50 % with an ambient temperature of 45°C. Never use the device during

thunderstorms. Over voltage could destroy the device. Always disconnect the device during thunderstorms.

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.

• Never let the power cable come into contact with other cables.

Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals, as this

will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle the

power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is 240V AC~50Hz.

• Make sure that the power cable is never crimped

or damaged. Check the equipment and the power

cable periodically.

• If the equipment is dropped or damaged, disconnect the mains

power supply immediately and have a qualied engineer inspect

the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached room

temperature.

• If your product fails to function correctly, stop use immediately.

Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS NO

USER SERVICEABLE PARTS.

• WARRANTY: One year from date of purchase.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

www.prolight.co.uk DMX Mirror Ball Rotator User Manual 3

Product overview & technical specications

Suitable for driving mirror balls up to a maximum weight of 180kg, this weight corresponds with a diameter of

200cm for our Equinox mirror balls. (The max. load is always the mirror ball weight including the mirror ball chain,

the safety chain and the xation material.)

This rotator can be operated in stand alone mode, via a DMX interface

and is programable via DIP switches, (DMX512 control is possible

via most 1 channel DMX controller) and has three functions:

Rotation direction, rotation speed and master/slave.

For professional use in pubs, clubs and in a variety of

other environments where the EN DIN 56950 norms

have to be considered.

• Rugged construction with steel housing for long operation

• Large motor axle for high stability

• Additional attachment eyelet for secondary

attachment of the load

• Complies with the safety norm EN 292

Heavy Duty DMX Mirror Ball Rotator

01 - Mirror ball motor

02 - Motor axle

03 - Screw-on chain link

04 - Mirror ball chain

05 - Installation eyelet

06 - Mirror ball

07 - Safety eyelet

08 - Safety chain

09 - Safety eyelet

In the box:

1 x rotator &

1 x user manual

Specications

Power supply 240V, 50Hz

Power consumption 20W

Max. load BGV C1 (7:1 safety factor) 180kg

Max. diameter of mirror ball 200cm

Rotation speed up to 1 RPM

Dimensions 235 x 292 x 252mm

Weight 11.1kg

Order code MIRR22

www.prolight.co.uk DMX Mirror Ball Rotator User Manual 4

Installation

The motor must be installed in an absolutely horizontal position in a vibration-free, oscillation-free and re-resistant location

If the motor and the mirror ball are to be operated above persons, additional risks arise. A hazard analysis based on the

location and application must be performed. Both the motor and mirror ball must meet the safety regulations regarding

safety and operation.

The installation point of the mirror ball has to be built and constructed in a way that it can hold 7 times the weight of the mir-

ror ball for one hour without any deformation.

The unit must always be secured with a secondary safety attachment. This secondary attachment must be constructed in a

way that no part of the unit can fall if the main attachment fails.

When rigging, derigging or servicing the unit, no persons should be in the area below/above the installation, or in other areas

which may be a hazard.

The operator has to make sure that safety relating and machine technical installations are approved by a competent,

qualied expert before starting operation for the rst time and before starting operation if changes have been made

to the installation.

Attachment:

The rotary motor should ideally be installed away from areas where persons may walk by or be seated under.

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to) calculation of work load

limits, installation materials being used, and periodic safety inspections of all installation materials and the mirror ball. If you

lack these qualications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper

installation can result in bodily injury and/or damage to property.

The motor and mirror ball have to be installed out of the reach of people.

If the motor is to be lowered from the ceiling or high joists a professional rigging system must be used. The motor must never

be xed swinging freely.

The motor must always be installed via all xing holes. Only use appropriate screws and make sure screws are properly

attached to the material point.

The durability of the installation depends very much on the material used at the installation area (building materials) such

as wood, concrete, brick etc. Always ask a specialist for the correct plug/screw combination by specifying the maximum load

and the building material.

DANGER TO LIFE!

PLEASE CONSIDER THE EN 60598-2-17 AND THE RESPECTIVE NATIONAL

REGULATIONS DURING THE INSTALLATION. THE INSTALLATION MUST ONLY

BE CARRIED OUT BY A COMPETENT AND QUALIFIED INSTALLER!

www.prolight.co.uk DMX Mirror Ball Rotator User Manual 5

Installation & maintenance

The ttings used for installation must never include abrading material

eg steel cables in order to avoid wear through abrasion.

The length of the chain must never exceed 100cm.

Install the mirror ball chain with the screw-on chain link at the installation eyelet of the mirror ball and tighten with the

xing screw.

Insert the fourth chain link of the mirror ball chain with the mirror ball in the screw-on chain link and tighten the xing screw.

For overhead use, always install a safety chain on the mirror ball that can hold at least 7 times the weight of the complete

installation. The safety chain must always be slightly longer than the mirror ball chain so the safety chain will always be

tension-free. Attach the safety chain to the safety eyelet on the mirror ball and then onto the safety eyelet on the motor.

The maximum drop distance for any safety device must never exceed 20cm.

A safety chain which has already taken the strain of a drop, or which is defective, must not be used again and must

be replaced.

The mirror ball must never be hung from the safety eyelet. Loads must only be hung on the motor axle. If a mirror ball hangs

for any reason from the safety eye, the motor must be taken out of operation immediately and the mirror ball must be

uninstalled. The whole installation must be checked for any defects by a competent, qualied expert.

Make sure the rotation of the mirror ball is never slowed or stopped by decoration material etc.

Make sure that no side forces can impact on the installation.

Please check at regular intervals, if the installation material or chain links have become deformed. Uninstall the mirror ball

immediately in such a case.

Cleaning & maintenance:

The operator has to make sure that safety relating and machine technical installations are approved by a competent,

qualied expert after every four years in the form of an acceptance test. The operator has to make sure that safety relating

and machine technical installations are approved by a skilled person once a year.

The following points have to be considered during the inspection:

1 - All screws used for installing the motor or parts of the motor have to be tightly connected and must not be corroded.

2 - There must not be any deformities on housings, xings and installation points (ceilings, trussing).

3 - Mechanically moving parts like axles and safety eyes must not show any traces of wearing (e.g. material abrading or

damages) and must not rotate with any unbalance.

4 - The electric power supply cables must not show any damage or, material fatigue. Further instructions depending on the

installation point and usage have to be adhered to by a skilled installer.

We recommend frequent cleaning of the motor. Please use a soft lint-free and moistened cloth. Never use alcohol or

solvents! There are no serviceable parts inside this motor. Maintenance and service operations are only to be carried out

by authorised dealers.

Should you need any spare parts, please use genuine parts. If the power supply cable of this unit is damaged, it has to be

replaced by an authorised dealer only in order to avoid hazards. If defective, please dispose of the motor in accordance with

current legal regulations. Should you have any further questions, please contact your dealer.

DANGER TO LIFE!

DISCONNECT FROM MAINS BEFORE STARTING MAINTENANCE OPERATION.

www.prolight.co.uk DMX Mirror Ball Rotator User Manual 6

Operating instructions

Master/slave operation:

The master/slave operation enables that several devices can be synchronized and controlled by one master device.

On the rear panel of the device you can nd an XLR jack and an XLR plug, which can be used for connecting several devices.

Choose the device which is to control the effects. This device then works as master device and controls all other

slave devices, which are to be connected to the master device via a DMX-cable. Connect the OUT jack with the IN plug

of the next device.

Please see further instructions under Operation on page 6.

Connection with mains:

Connect the device to the mains with the power plug.

The occupation of the connection cables is as follows:

Attention! The earth has to be connected!

If the device will be directly connected with the local power supply network,

a disconnection switch with a minimum opening of 3mm at every pole has to

be included in the permanent electrical installation.

The device must only be connected with an electric installation carried out in

compliance with the IEC standards. The electric installation must be equipped

with a Residual Current Device (RCD) with a maximum fault current of 30mA.

Operation:

The device has two operating modes. It can be operated via DIP Switches or it can be run in DMX-controlled mode.

Operation via dip switches:

Manual Mode: Rotation Direction and Speed

In order to select Manual Mode, set DIP- switch 10 to OFF.

Rotation speed can be selected via DIP-switch 1: 0.5 RPM = ON; 1 RPM = OFF.

Rotation direction can be selected via DIP-switch 2: clockwise = OFF; counterclockwise = ON.

DIP-switches 3 to 9 have no function.

Master/slave:

In order to select the Master unit, set DIP-switch 10 to ON. Set DIP-switch 10 to OFF on the Slave devices.

DMX controlled operation:

You can control the devices individually via your DMX-controller. Every DMX-channel has a different occupation with different

features. For DMX-controlled operation set DIP Switch 10 to ON. Use DIP Switches 1 to 9 to set the desired DMX addresses.

Addressing:

Each DMX rotator occupies 1 channel. To ensure that the control signals are properly directed to each device, the device

requires addressing. This is to be adjusted for every single device by changing the DIP-switches as set out in the table below.

The starting address is dened as the rst channel from which the device will respond to the controller.

Please make sure that you do not have any overlapping channels in order to control each device correctly and independently

from any other xture on the DMX data link. If two, three or more devices are addressed similarly, they will work similarly.

Cable Pin International

Brown Live L

Blue Neutral N

Yellow/Green Earth

www.prolight.co.uk DMX Mirror Ball Rotator User Manual 7

Setting the DMX address:

The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address” from 1- 512.

A xture requiring one or more channels for control begins to read the data on the channel indicated by the start address.

For example, a xture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would read

data from channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used do not overlap.

E.g. the next unit in the chain starts at 107.

DMX 512:

DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent xtures and controllers.

A DMX controller sends DMX data instructions form the controller to the xture. DMX data is sent as serial data that travels

from xture to xture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only

have a data “out” terminal).

DMX linking:

DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single

controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using

several DMX xtures try to use the shortest cable path possible. The order in which xtures are connected in a DMX line does

not inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in a DMX

line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a DMX address of 1, the DMX

controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):

This xture can be controlled via DMX-512 protocol. The DMX

address is set on the back of the unit. Your unit and your

DMX controller require a standard 3-pin XLR connector

for data input/output, see image.

Also remember that DMX cable must

be daisy chained and cannot be split.

Maintenance & DMX setup

Further DMX cables can be

purchased from all good sound

and lighting suppliers or Prolight

Concepts dealers. Please quote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

Occupation of the DIP-switches:

DMX protocol:

Rotation direction and speed

Channel Value Function

000-000 No rotation

001-127 Decreasing clockwise rotation

128 No rotation

129-255 Increasing counter-clockwise rotation

Setting the DMX

starting address

DIP Switch

number 1 2 3 4 5 6 7 8 9

Device number

and channels

Starting

address 1 2 4 8 16 32 64 128 256

Device 1

- Channel 1

OFF

Device 2

- Channel 2

OFF

Device 3

- Channel 3

OFF

Device 4

- Channel 4

OFF

Device 5

- Channel 5

OFF

www.prolight.co.uk DMX Mirror Ball Rotator User Manual 8

DMX setup & WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed of with other household

wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable

reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government

ofce, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

Notice:

Be sure to follow the diagrams below

when making your own cables. Do not

connect the cables shield conductor

to the ground lug or allow the shield

conductor to come in contact with the

XLRs outer casing. Grounding the

shield could cause a short circuit

and erratic behaviour.

Special note:

Line termination:

When longer runs of cable are used, you may need to use

a terminator on the last unit to avoid erratic behaviour.

Using a cable terminator will decrease the possibilities

of erratic behaviour.

(3-pin - Order code: CABL9O, 5-pin - Order code: CABL89)

5-pin XLR DMX connectors:

Some manufactures use 5-pin XLR

connectors for data transmission in

place of 3-pin. 5-pin XLR xtures may

be implemented in a 3-pin XLR DMX line.

When inserting standard 5-pin XLR

connectors in to a 3-pin line a cable

adaptor must be used. The diagram

below details the correct cable conversion.

Termination reduces signal transmission

problems and interference. it is always

advisable to connect a DMX terminal,

(resistance 120 Ohm 1/4 W) between pin 2

(DMX-) and pin 3 (DMX+) of the last xture.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

Tabla de contenidos

Otros manuales de Equipo de DJ de Equinox Systems

Equinox Systems

Equinox Systems CARBON Manual de usuario

Equinox Systems

Equinox Systems C-Shot Manual de usuario

Equinox Systems

Equinox Systems Waterwave XP Manual de usuario

Equinox Systems

Equinox Systems EQLED368 Manual de usuario

Equinox Systems

Equinox Systems Fusion Orbit Manual de usuario

Equinox Systems

Equinox Systems FUSION SPOT XP MKIII Manual de usuario

Equinox Systems

Equinox Systems Triton Beam EQLED071 Manual de usuario

Equinox Systems

Equinox Systems Fusion 140 Manual de usuario

Equinox Systems

Equinox Systems MaxiPar Tri MKII Manual de usuario

Equinox Systems

Equinox Systems PFM1500 Manual de usuario

Equinox Systems

Equinox Systems PRO DJ Booth Quad-colour Starcloth Manual de usuario

Equinox Systems

Equinox Systems Graphix Manual de usuario

Equinox Systems

Equinox Systems Crossfire XP Manual de usuario

Equinox Systems

Equinox Systems EQLED003 Manual de usuario

Equinox Systems

Equinox Systems Hallucination Manual de usuario

Equinox Systems

Equinox Systems Power Par 54 MKII Manual de usuario

Equinox Systems

Equinox Systems Microbor EQLED60 Manual de usuario

Equinox Systems

Equinox Systems Domin8R II Manual de usuario

Equinox Systems

Equinox Systems EQLED082 Manual de usuario

Equinox Systems

Equinox Systems Micro Batt EQLED160 Manual de usuario

Equinox Systems

Equinox Systems Waterwave 50W Manual de usuario

Equinox Systems

Equinox Systems Ultra LED Scan EQLED75 Manual de usuario

Equinox Systems

Equinox Systems Spark Stream Manual de usuario

Equinox Systems

Equinox Systems EQLED12B Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario