EQUILAB SMARTMARKER Manual de usuario
SMARTMARKER
new page /
duplicate page/
wake-up
power
status
power status
SMARTMARKER
sensor
Bluetooth status
color ring
marker
release
SMARTMARKER
marker
cap
SMARTMARKER
sleeve
power button
charging
case
accessory
box
Bluetooth
button
sensor
USB port
USB charge
port
1
Components
Record and organize written notes.
Stream, edit, enhance and share
them with friends and colleagues.
Convert your handwriting to text for
easy editing and sharing. For
download instructions, see the
following page.
Equil Note App
charging cable
2 markers
USB power Adapter
eraser eraser bracket
user guide quick start card
color rings
sensor mounting
bracket
2
eraser cap accessory
direct connect cable
*Ferrite core: CU0930B
3
Tablet
Computer
Phone
Charging
Tips
Use the wall adapter for faster
charging.
You may use any micro-USB
cable to charge your Equil
Smartmarker.
The amber LED indicates active
charging. Green LEDs indicate
that charging is complete.
❶Download and install Equil Note
iOS the App Store
Android™ Google Play™
Mac OS X® the Mac App Store
Windows myequil.com
❷Charge your marker and sensor
Fully charge Equil
Smartmarker
before use.
Charging takes
approximately
two hours.
Once charged, your
Equil Smartmarker
can be used
continuously for up
to eight hours.
USB
Equil Note platform available on
❸Turn on the sensor
The Power button is found on the side
of the sensor.
4
Power
Tips
To save battery power,
the sensor will turn off
automatically after 60
minutes of inactivity.
❹Set Bluetooth Mode
Before you pair with your iPhone/iPad/iPod, press
the Bluetooth mode button to select iOS mode.
The Bluetooth mode button is found on the
side of the sensor. The default mode is iOS.
Before you pair with your Android, Mac OS or
Windows device, press the Bluetooth mode button
to select
❺Pair sensor with your device
5
Tips
❶Press and hold the Bluetooth
button (1) until the Bluetooth
LED (2) on the front of the
sensor blinks fast. Then
release button.
❷Turn on Bluetooth for the
device you are pairing
(phone, tablet, computer)
and select “EquilSM-xxxxxx”
in the devices list.
❸ When pairing is complete, the
Bluetooth LED will start to
blink slowly (approx. once
every 2 seconds).
Note: When Equil Note
is open, Bluetooth LED
will stay solid.
For more detailed pairing info
for your specific device, refer
to the tutorial in Equil Note.
To pair with a new device
when a previously-paired
device is nearby, you may
need to delete/remove
“EquilSM-XXXXXX” from the
list of devices paired on the
other device.
Pairing
Depending on the size and orientation of your
whiteboard, the sensor can be centered
vertically on either side––or in the middle––of
your writing area.
❻Place sensor on your
whiteboard
6
Tips
Setup
Position the sensor where it
will be convenient to press
the new page button.
If your board area is wider
than 8 feet, place the
sensor in the center and
write notes on both sides,
up to 16 feet wide.
If you write too far from the
sensor, it will alert you to stay
within the recording area.
For your notes to be captured,
you must write at least 2 inches
away from the sensor. If you
write too close to the sensor, it
will alert you to move back into
the writing area.
draw
area
draw
area
draw
area
draw
area
draw
area
The charging case provides a
handy place to store the
Smartmarker, and keeps it
charged and ready for use.
The sensor is always portable.
Simply remove the sensor
from its magnetic hold in the
charging case and place on
other whiteboard surfaces.
To use your Smartmarker
while the sensor is docked
in the charging case, make
sure that you attach the
charging case on the left
side of your whiteboard.
The sensor will continue to
function, but will no longer
capture writing on the
left side.
Installation
Tips
7
❶Attach metal mounting
bracket to sensor.
❷Remove protective
backing.
❸Place sensor on surface,
press firmly for best
adhesion.
Place sensor on
magnetic whiteboard.
All Other Surfaces
Magnetic Whiteboards
Using the charging case on
your whiteboard
You can set up a more permanent installation by
plugging the charging case into a power outlet.
Use the provided 10 foot (3 meter) USB cable
and the USB power adapter to plug the charging
case into the nearest electrical outlet.
draw area
❼Install the dry erase marker
❷Remove the
Smartmarker cap
❺Replace the
Smartmarker cap
❶ Open the
marker barrel ❸ Pull out and change
the color ring if desired
❹ Insert the
corresponding
dry erase marker
Tips
8
Replace the cap firmly to
prevent the marker from
drying out.
The marker color in the software
is determined by the color ring
used on the Smartmarker,
regardless of what color marker
is placed inside.
Marker
❽Install the eraser battery
❷Install
battery
negative
side up
❸Replace
battery
cover
–
+
❾Install eraser bracket
Remove the
adhesive backing
Place mounting
bracket horizontally
on surface
draw area
Note: Park eraser outside of drawing area
Tips
9
If your Smartmarker or eraser
battery is running low, the
amber LED will blink 5 times
when you turn on the sensor
to remind you to recharge
soon.
The Smartmarker and eraser
have no power buttons. They
will turn off automatically.
Battery Eraser Bracket
The eraser bracket allows
you to park the eraser on
any surface.
❶Open the battery
cover: Slide downward
and remove
Otros manuales para SMARTMARKER
2
Tabla de contenidos
Idiomas:
