EQK J1-72 Manual de usuario
REMOTE
18
Remote controller 1
Operation instructions
Operation modes 3
3
Airflow direction control 4
Smart mode 5
Clock button 5
Timer mode 6
8° Heating mode 7
Super mode 7
Sleep mode 8
Ifeel mode 8
Remote controller Instructions
(J1-72)
Remote controller
1
1
2
3
13
45
6
12
11
8
7
9
10
SUPER BUTTON
SWING BUTTON
FAN BUTTON
ROOM TEMPERATURE
SETTING BUTTONS
SLEEP BUTTON
IFEEL BUTTON
CLOCK BUTTON
ON/OFF BUTTON
SMART BUTTON
MODE BUTTON
TIMER ON/OFF BUTTON
61°F(16
°F(30
.)
.
Remote controller
Indication symbols on LCD:
14 DIMMER BUTTON
.
15 SWING BUTTON
16 MUTE BUTTON
17 8 BUTTON°HEAT
° .
Note: Each mode and relevant function will be further specified in following pages.
FF
88
12
ON/OFF
MODE FAN
SLEEP SUPER
SMART IFEEL DIMMER
TIMER ON TIMER OFF CLOCK
SWING
SWING
MUTE
FFFF
8
8HEAT
10
11
13
14
3
4
1
2
6
8
5
7
9
16
17
15
ON
OFF
ON
OFF
ON/OFF
MODE FAN
SWING SLEEP SUPER
SMART IFEEL DIMMER
TIMERON TIMEROFF CLOCK
8
SWING MUTE
8
HEAT
How to Insert the Batteries
How to Use
Remove the battery cover according to the arrow direction.
Insert new batteries making sure that the (+) and (-) of
battery are matched correctly.
Reattach the cover by sliding it back into position.
Note:
Use 2 LR03 AAA(1.5volt) batteries. Do not use rechargeable batteries.
Replace batteries with new ones of the same type when the display
becomes dim.
Storage and Tips for Using the Remote Controller
The remote controller may be stored mounted on a wall with a holder.
Note: The remote controller holder is an optional part.
2
To operate the room air conditioner, aim
the remote controller to the signal receptor.
The remote controller will operate the air
conditioner at a distance of up to 7m when
pointing at signal receptor of indoor unit.
Remote controller
Remote controller
Signal receptor
CAUTIONS
For appropriate signal transmission between remote controller and
indoor unit, keep the signal receiver away from the following items:
Direct sunlight or other strong lights or heat
Flat panel television screen or other electrical appliances that
react to the remote controller
Additionally, the air conditioner will not operate if curtains, doors or
other materials block the signals from the remote controller to the
indoor unit. If the signal may not be transmitted properly, either move
these materials or consult your local dealer.
.
F
°F 1℃.
°F 1℃.
°
－
F
Operation instructions
3
ON/OFF
MODE FAN
SLEEP SUPER
SMART IFEEL DIMMER
TIMER ON TIMER OFF CLOCK
SWING
SWING
MUTE
FFFF
8
8HEAT
1
4
2
3
61°F ~°F(16℃~30℃)
Note: ”
together for 3 seconds will alternate the temperature display
between the ℃ and °F scale.
Note: Heating mode is NOT available for cooling only models.
Note: At “Dry” mode, the unit can decrease or rise 7°F by remote
controller if you feel uncomfortable.
Press and hold “ MODE” button and “ button
SWING
5
Airflow direction control
Vertical airflow(Horizontal airflow) is automatically adjusted to a certain
angle in accordance with the operation mode after turning on the unit.
The direction of airflow can be
also adjusted to your own
requirement by pressing the
"SWING" button of the
remote controller.
Operation mode Direction of airflow
COOLING, DRY
*HEATING,
FAN ONLY
horizontal
downward
Vertical airflow control (with the remote controller)
Using remote controller to set various angles of flow or specific angle
as you like.
Swinging airflow
Pressing " SWING" button once, the vertical adjustment louver will
swing up and down automatically.
Desired direction airflow
Pressing the " SWING" button again when the louvers swing to a
suitable angle as desired.
Do not turn the vertical adjustment louvers manually, otherwise malfunction may occur. If that happens, turn off the
unit first and cut off the power supply, then restore power supply again.
It is better not to let the vertical adjustment louver tilt downward for a long time at COOLING or DRY mode to prevent
condensed water from dripping.
Operation instructions
4
*Heating mode is only available for heat pump models.
Airflow direction control
Horizontal airflow control (with the remote controller)
Using remote controller to set various angles of flow or specific angle
as you like.
Swinging airflow
Pressing " SWING" button once, the horizontal adjustment louver will
swing left and right automatically.
Desired direction airflow
Pressing the " SWING" button again when the louvers swing to a
suitable angle as desired.
NOTE:If the unit doesn’t have four ways airflow function,you can adjust horizontal
airflow by yourself.(invalid for some models)
ON/OFF
MODE FA N
SLEEP SUPER
SMART IFEEL DI MM ER
TIMER ON TIMER OFF CLOCK
SWING
SWING
MUTE
ON
OFF
ON
OFF
8
8 HEAT
SMART button is ineffective in SUPER mode.
Your feeling
What you can do in SMART mode
button adjustment procedure
Press the SMART button, the unit enters SMART mode(fuzzy logic operation) directly regardless of
the unit is on or off. In this mode, temperature and fan speed are automatically set based on the
actual room temperature.
Uncomfortable
because of
unsuitable air
flow volume.
Uncomfortable
because of
unsuitable flow
direction.
Indoor fan speed alternates among
Auto, Higher, High, Medium, low and Lower
each time this button is pressed.
Press it once, the vertical adjustment louver
swings to change vertical airflow direction.
Press it again, swings stops.
For horizontal airflow direction, please
refer to the previous page for details.
Note: Temperature, airflow and direction are controlled automatically in SMART mode.
However, for the inverter you can choose from -7 to 7.If you still feel uncomfortable.
Operation instructions
5
SMART mode
CLOCK button
You can adjust the real time by pressing CLOCK button, then
using and buttons to get the correct time, press
CLOCK button again the real time is set.
FAN
SWING
SWING
Press MODE button cancel SMATR mode.
ON/OFF
MODE FAN
SLEEP SUPER
SMART IFEEL DIMMER
TIMER ON TIMER OFF CLOCK
SWING
SWIN G
MUTE
ON
OFF
ON
OFF
8
8 HEAT
Indoor temperature Target temperature
70 )°F(21℃ or below 72 )°F(22℃
79°F(26℃)Over 79°F(26℃)
70°F °F(21℃~23℃)-73
73 -79°F °F(23℃~26℃)
Operation mode
HEATING
FAN ONLY
DRY Room temperature
decrease 2°F(2℃） after
operate for 3 minutes
COOLING
Operation mode and temperature are determined by indoor temperature
Heat pump models
Cooling only models
Indoor temperature Target temperature
73 )°F(23℃ or below
79°F(26℃)
Over 79°F(26℃)
73°F °F(23℃~26℃)-79
Operation mode
FAN ONLY
DRY Room temperature
decrease 2°F(2℃） after
operate for 3 minutes
COOLING
6
TIMER mode
The TIMER ON button can be used to set the timer to switch on the appliance at your
desired time.
Press the TIMER ON button and when "ON 12:00" flashes on the LCD display, you can
then press the or buttons to select the time you wish for the appliance to turn on.
Press the or button once to increase or decrease the time setting by 1 minute.
Press the or button 2 seconds to increase or decrease the time setting
by 10 minutes.
Press the or button for a longer time to increase or decrease the time by 1 hour.
Press the TIMER ON button again. Once you hear a "beep" and the indicator disappears,
the TIMER ON mode has been canceled.
A "beep" will sound.
Note: If you don't set the time in 10 seconds after you press the TIMER ON button, the remote control
will exit the TIMER ON mode automatically.
Note: It is similar to set TIMER OFF. You can make the appliance switch off automatically at
your desired time.
The TIMER indicator on the indoor unit lights up.(invalid for some models)
"ON" stops flashing.
After the set timer is displayed for 5 seconds the clock will be displayed on the LCD
of the remote control.
It is convenient to set the timer on with TIMER ON buttons when you go out in the
morning to achieve a comfortable room temperature when you get home. You can also
set the timer off at night to enjoy a good sleep.
Operation instructions
How to set the TIMER ON
How to cancel TIMER ON
Increase
Decrease
i)
it.
When your desired time is displayed on the LCD, press the TIMER ON button and confirm
ii)
iii)
ON
7
Operation instructions
SUPER mode
SUPER mode
8° HEATING mode
The mode will be started when you press at
the heating mode.
8°HEATING 8°HEAT button
If you
and SWING button, you can escape from 8°HEATING mode.Then the
display will disappear and the 8°HEATING mode will be cancelled.
press any button except for TIMER ON, TIMER OFF, CLOCK, IFEEL
In 8°HEATING mode, the fan speed is set at "AUTO" automatically.
8°HEAT button is used to set 8 heating mode. ℃
8° HEATING mode
8
Note:
mode can be set only when the air conditioner works in the heating mode.8°HEATING
In mode, the temperature is set 8 .8°HEATING default ℃
8
SUPER mode can be set when the appliance is in operation or energized.
In SUPER mode, you can set airflow direction or timer.
If you want to escape from SUPER mode, press SUPER, MODE, FAN,
ON/OFF or SLEEP button, the display will return to the original mode.
temperature,
Note:
The Appliance will continue working in SUPER mode , if you don't escape from it by
pressing any of the buttons mentioned above.
SMART button is not available in SUPER mode.
SUPER mode is used to start or stop fast cooling or heating. In SUPER
mode, the super indicator will .
Fast cooling operates at high fan speed, changing the set temperature
automatically to 61°F(16℃);Fast heating operates at auto fan speed, changing the
set temperature automatically to 86 °F(30℃).
display on LCD
Heating is NOT available for cooling only air conditioner.
For the first generation of products, you can’t set temperature in super mode, but you
can press TEMPERATURE SETTING button to escape super mode.
ON
OFF
ON
8
Operation instructions
SLEEP mode
Note: When using IFEEL mode, advice to put the remote in the place where the indoor unit can
receive the signal easily.
Note: When stopping the air conditioner, advice to cancel the IFEEL mode so as to save energy.
In IFEEL mode, the temperature sensor built in remote controller is activated. It can
sense its surrounding temperature, and transmit the signal back the unit, the unit
can adjust the temperature so as to provide maximum comfort.
IFEEL mode
IFEEL mode
SLEEP mode
SLEEP mode can be set in COOLING ,HEATING mode. or DRYING
This function gives you a more comfortable environment for sleep.
The appliance will stop operation automatically after operating for 8 hours.
Fan speed is automatically set at low speed.
Note: Heating is NOT available for cooling only air conditioner.
Set temperature will rise by 2 ) if the appliance operates in cooling °F(2℃mode at most
for 2 hours constantly, then keeps steady.
Set temperature will decrease by 2 )°F(2℃ at most if the appliance operates in heating
mode for 2 hours constantly, then keeps steady.
SLEEP mode 1:
Set temperature will rise by 2 ) if the appliance operates in cooling
constantly, decrease by 1°F(1℃) after 6 hours, then decrease by 1°F(1℃) after 7 hours.
°F(2℃mode for 2 hours
Set temperature will decrease by 2°F(2℃) if the appliance operates in heating mode for
hours constantly, rise by 1°F(1℃) after 6 hours, then rise by 1°F(1℃) after 7 hours.
SLEEP mode 2:
Set temperature will rise by 1 ) if the appliance operates in cooling
hour, rise by 2°F(2℃) after 2 hours, then decrease by 2°F(2℃) after 6 hours,
decrease by 1°F(1℃) after 7 hours.
°F(1℃mode for 1
Set temperature will decrease by 2°F(2℃) if the appliance operates in heating mode
for 1 hour , decrease by 2°F(2℃) after 2 hours, then rise by 2°F(2℃) after 6 hours,
rise by 2°F(2℃) after 7 hours.
SLEEP mode 3:
Set temperature will keeps steady.
SLEEP mode 4:
Each time SLEEP button is pressed, the operation mode is changed in sequence:
SLEEP 2 SLEEP 3 QUIT SLEEP MODE
SLEEP 4
SLEEP 1
Note: Press SUPER ,SMART, MODE,SLEEP or FAN button cancel SLEEP mode.
Tabla de contenidos
Idiomas:
Otros manuales de Mando a distancia de EQK
