Epson Perfection V700 Series Manual de usuario

Epson Perfection V700 Photo/V750 Pro

12/05 Epson Perfection V700 Photo/V750 Pro - 1

Scanner Parts

Note: The Epson Perfection V750 Pro also includes a fluid mount

tray.

Scanner Specifications

General

Document

table

Carriage and

lamp (in the

home position)

USB port

inlet

OPTION

port

Scan button

Scanner cover

Transparency unit

transportation lock

Document mat

Cover

cable

Scanner

transportation lock

Power switch

FireWire®

1394 port

Scanner type Flatbed color

Photoelectric device Color CCD line sensor

Effective pixels 40,800 ×56,160 pixels (4800 dpi)

37,760 ×62,336 pixels (6400 dpi)

Document size Documents or photos:

8.5 ×11.7 inches (216 ×297 mm)

US letter or A4 size

Film or slides:

8 × 10 inches (203.2 ×254 mm),

four 35mm film strips (6 frames each),

twelve 35mm slides, two medium

format (6 ×20 cm film frame), or two

4 ×5 inch film frames

Scanning resolution 4800 dpi (main scan)

6400 dpi (main scan)

9600 dpi with Micro Step (sub scan)

Output resolution 50 to 12800 dpi in 1 dpi increments

Film holder for filmstrips

4 ×5 inch film holder

Film area guide (for large-

format film up to 8 ×10

inches)

Medium format film holder

Slide holder

Epson Perfection V700 Photo/V750 Pro

2 - Epson Perfection V700 Photo/V750 Pro 12/05

Mechanical

Electrical

Note:

Check the label on the AC adapter or on the back of the scanner for

voltage information.

Scanner

AC Adapter

Environmental

Interfaces

USB Interface

FireWire Interface

Standards and Approvals

Scanner

AC Adapter

Scanning speed V700 Photo: approximately 12.3 msec

per line at 4800 dpi

V750 Pro: approximately 11.8 msec per

line at 4800 dpi

Approximately 3.1 msec per line at

600 dpi

Image data 16 bits per pixel per color internal

16 bits per pixel per color external

(maximum)

Light source White cold cathode fluorescent lamp IR

LED

Dimensions Width: 19.8 inches (503 mm)

Depth: 12.1 inches (308 mm)

Height: 6 inches (152.5 mm)

Weight Approx. 14.5 lb (6.6 kg)

Input voltage DC 24 to 26.4 V

Rated voltage DC 24 V

Rated current 1.4 A

Power consumption 32 W operating

20 W stand-by mode

3.8 W sleep mode

Rated input voltage AC 100 to 120 V

Rated input current 0.8 A

Ratedfrequency 50to60Hz

Rated output voltage DC 24.0 to 26.4 V

Rated output current 1.4 A

Temperature Operating 41 to 95 °F (5 to 35 °C)

Storage –13 to 140 °F (–25 to 60 °C)

Humidity Operating 10 to 80%, without condensation

Storage 10 to 85%, without condensation

Operating

conditions

Ordinary office or home

conditions.

Avoid operating the scanner in

direct sunlight, near a strong light

source, or in extremely dusty

conditions.

Interface type Universal Serial Bus Specification Revision

2.0

Electrical standard Full Speed mode (12 Mbits per second)

and Hi-Speed mode (480 Mbits per

second) of Universal Serial Bus

Specification Revision 2.0.

Connector type One Type B port

Interface type IEEE Std 1394a-2000

Electrical standard ANSI X3T10 Serial Bus Protocol 2

Revision 4L (SBP-2)

Connector type One 6-pin port

EMC FCC Part 15 Subpart B Class B

CAN/CSA-CEI/IEC CISPR 22 Class B

Safety UL60950-1

CAN/CSA-22.2 No. 60950-1-03

EMC FCC Part 15 Subpart B Class B

CAN/CSA-CEI/IEC

CISPR22 Class B

Epson Perfection V700 Photo/V750 Pro

12/05 Epson Perfection V700 Photo/V750 Pro - 3

Scanning a Document or Photo

Before scanning a document, remember to respect the rights of

first checking their copyright status.

Caution: Do not place heavy objects on the document table glass

and do not press the glass with too much force.

1. Open the scanner cover.

Make sure the document mat is installed inside the cover. If

it is not installed, see “Replacing the Document Mat” on

page 9 for instructions.

2. Place your document or photo on the document table, face

down on the glass. Make sure the top of the document or

photo is against the upper right corner of the document

table.

3. If you are scanning multiple photos at once, position each

photo at least 0.8 inches (20 mm) apart from the others.

Note: If you are scanning large or thick documents, you can

remove the scanner cover. See “Placing Large or Thick

Documents” below for instructions.

4. Close the scanner cover gently so that your original does not

move.

Note: Always keep the document table clean. Do not leave photos on

the document table for an extended period of time as they may stick

to the glass.

Placing Large or Thick Documents

When you scan a large or thick document, you can remove the

scanner cover.

1. Turn off the scanner using its Ppower button.

2. Disconnect the cover cable.

Epson Perfection V700 Photo/V750 Pro

4 - Epson Perfection V700 Photo/V750 Pro 12/05

3. Open the scanner cover.

4. Lift the scanner cover straight up and off the scanner.

5. Turn on the scanner using its Ppower button.

Note: When scanning without the scanner cover, gently press

down on your document to flatten it.

6. When you are finished scanning, replace the scanner cover

in the reverse order that you removed it.

Scanning Film and Slides

Removing the Document Mat

To scan film strips or slides, you need to remove the document

mat from the scanner cover. This uncovers the transparency

unit so your scanner can use it to scan your film or slides.

1. Make sure the cover cable is connected to the scanner’s

OPTION port.

Note: Before connecting or disconnecting the cover cable, turn

off the scanner using its Ppower button.

2. Open the scanner cover and gently slide up the document

mat to remove it. Also make sure the transparency unit

transportation lock is unlocked.

Epson Perfection V700 Photo/V750 Pro

12/05 Epson Perfection V700 Photo/V750 Pro - 5

3. Use a soft cloth to wipe the transparency unit window and

the document table before placing your film or slides.

To place film or slides for scanning, see the sections below.

Placing Film in the Holder

Placing 35mm Film Strips

1. Remove the film strip cover(s) on the film holder.

2. Slide up to four film strips all the way into the film holder

with the shiny base side facing down. Your images and any

wording on the film strips should appear backwards on the

side that faces up, as shown by the illustration on the film

holder.

Note: Hold the edge of the film gently or use gloves to touch the

film; otherwise you may damage the film. Make sure the white

stickers on the back of the film holder and the areas around them

are not scratched, dusty, or covered in any way. If the areas are

obscured, the scanner may have trouble recognizing your film in

Full Auto Mode. Do not cover any of the tiny holes in the film

holder or the scanner may have trouble recognizing which film

holder you are using.

3. Place the cover(s) over the film and press them down until

they click. Then press down on all the edges of the covers to

secure them.

4. Place the film holder on the document table so that it is

aligned with the upper right corner and the pins are seated

in the holes on the scanner.

5. Make sure you removed the document mat. See “Removing

the Document Mat” on page 4.

6. Close the scanner cover.

When you are finished scanning film, be sure to replace the

document mat before scanning documents or photos. See

“Replacing the Document Mat” on page 9.

Placing Medium Format Film

1. Open the cover on the medium format film holder.

2. Slide up to two medium format film images into the film

holder with the shiny base side facing down. Your images

and any wording on the film should appear backwards on

Epson Perfection V700 Photo/V750 Pro

6 - Epson Perfection V700 Photo/V750 Pro 12/05

the side that faces up, as shown by the illustration on the

film holder. Make sure the entire image frame is positioned

in the film holder opening.

Note: Hold the edge of the film gently or use gloves to touch the

film; otherwise you may damage the film. Make sure the white

stickers on the back of the film holder and the areas around them

are not scratched, dusty, or covered in any way. If the areas are

obscured, the scanner may have trouble recognizing your film in

Full Auto Mode. Do not cover any of the tiny holes in the film

holder or the scanner may have trouble recognizing which film

holder you are using.

3. Close the cover over the film and press it down until it

clicks. Then press down on all the edges of the cover to

secure it.

4. Place the film holder on the document table so that it is

aligned with the upper right corner and the pins are seated

in the holes on the scanner.

5. Make sure you removed the document mat. See “Removing

the Document Mat” on page 4.

6. Close the scanner cover.

Note: You cannot use Full Auto Mode to scan medium format film.

When you are finished scanning film, be sure to replace the

document mat before scanning documents or photos. See

“Replacing the Document Mat” on page 9.

Placing 4 ×5 inch Film

1. Open the covers on the 4 ×5 inch film holder.

2. Place the film into the film holder with the shiny base side

facing down. Your images and any wording on the film

should appear backwards on the side that faces up, as shown

by the illustration on the film holder. Make sure the entire

image frame is positioned in the film holder opening.

Note: Hold the edge of the film gently or use gloves to touch the

film; otherwise you may damage the film. Make sure the white

stickers on the back of the film holder and the areas around them

are not scratched, dusty, or covered in any way. If the areas are

obscured, the scanner may have trouble recognizing your film in

Full Auto Mode. Do not cover any of the tiny holes in the film

holder or the scanner may have trouble recognizing which film

holder you are using.

3. Close the cover over the film and press it down until it

clicks. Then press down on all the edges of the cover to

secure it.

Epson Perfection V700 Photo/V750 Pro

12/05 Epson Perfection V700 Photo/V750 Pro - 7

4. Place the film holder on the document table so that it is

aligned with the upper right corner and the pins are seated

in the holes on the scanner.

5. Make sure you removed the document mat. See “Removing

the Document Mat” on page 4.

6. Close the scanner cover.

Note: You cannot use Full Auto Mode to scan 4 ×5 inch film.

When you are finished scanning film, be sure to replace the

document mat before scanning documents or photos. See

“Replacing the Document Mat” on page 9.

Placing Slides in the Holder

You can scan up to twelve 35mm slides at a time using the slide

holder.

Note: Make sure the white stickers on the back on the film holder

and the areas around them are not scratched, dusty, or covered in

any way. If the areas are obscured, the scanner may have trouble

recognizing your slides in Full Auto Mode. Do not cover any of the

tiny holes in the film holder or the scanner may have trouble

recognizing which film holder you are using.

1. Place up to twelve slides in the 35mm slide holder with the

shiny base side facing down. Your image should appear

backwards on the side that faces up, as shown by the

illustration on the film holder. The top of your images

should face the open end of the film holder as shown below.

2. Place the film holder on the document table so that it is

aligned with the upper right corner and the pins are seated

in the holes of the scanner.

3. Make sure you removed the document mat. See “Removing

the Document Mat” on page 4.

4. Close the scanner cover.

When you are finished scanning slides, be sure to replace the

document mat before scanning documents or photos. See

“Replacing the Document Mat” on page 9.

Epson Perfection V700 Photo/V750 Pro

8 - Epson Perfection V700 Photo/V750 Pro 12/05

Placing Film in the Film Area Guide

You can scan film that cannot be placed in the film holders (up

to 8 ×10 inch film) using the film area guide in Professional

Mode. When scanning film using the film area guide, always

select Film (with Film Area Guide) as the Document Type.

Note: You cannot use DIGITAL ICE Technology when scanning film

with the film area guide. When scanning using the film area guide,

striped (newton) rings may appear in your scanned images.

1. Make sure the tab on the long edge of the film area guide is

on the left side.

2. Fold the tab along the perforated lines as shown.

3. Place the film area guide on the document table with the tab

facing the left side of the scanner.

4. Place the film in the film area guide (up to 8 ×10 inch film)

with the shiny base side facing down. Your images and any

wording on the film should appear backwards on the side

that faces up. Make sure the entire image frame is

positioned in the film area guide opening.

Note: Leave the part of the film area guide shown below

uncovered or colors in your scans will be affected.

5. Make sure you removed the document mat. See “Removing

the Document Mat” on page 4.

6. Close the scanner cover.

Note: You cannot use Full Auto Mode or Home Mode when scanning

film with the film area guide.

When you are finished scanning film, be sure to replace the

document mat before scanning documents or photos. See

“Replacing the Document Mat” on page 9.

Epson Perfection V700 Photo/V750 Pro

12/05 Epson Perfection V700 Photo/V750 Pro - 9

Replacing the Document Mat

Replace the document mat by sliding it into the notches in the

scanner cover. Make sure the white surface faces outwards.

Scanning and Restoring Photos

Using the Color Restoration feature in EPSON Scan, you can

transform old, faded, or badly exposed photos into ones with

true-to-life color. You can restore printed photos, negative film,

or slides automatically as you scan them.

You can use Color Restoration in EPSON Scan’s Full Auto,

Home, or Professional Mode. For detailed steps, see the

on-screen User’s Guide.

Removing Dust and Scratch Marks

From Film or Slides

Using the Dust Removal feature in EPSON Scan’s Full Auto

or Professional Mode, you can virtually “clean” the dust marks

from film or slides as you scan them.

Your scanner and its EPSON Scan software are equipped with

the Digital ICE™ and Digital ICE Lite™ features that remove

stubborn dust or scratch marks from color film or slides.

DIGITAL ICE will not harm image details while Dust Removal

may degrade the image. However, it takes longer to scan using

DIGITAL ICE.

For detailed steps on using these features, see the on-screen

User’s Guide.

Reading the Scanner Light

If an error occurs, the scanner stops operating and the scanner

light flashes red. This indicates one of the following problems:

❏The scanner is not connected to your computer properly or

your software is not fully installed. See the Start Here sheet

that came with your scanner for instructions on installing

the scanner software and connecting the scanner to your

computer.

❏The scanner and/or the transparency unit transportation

lock is locked. Slide the lock to the unlock position.

❏The scanner cover cable is not connected to the scanner’s

OPTION port. Connect the cable to the port.

After trying these solutions, turn off the scanner using its power

button, then turn it back on.

If the scanner light is still flashing:

❏The scanner may be malfunctioning.

❏The scanner lamp may need to be replaced.

❏The connected optional equipment may be malfunctioning.

Contact Epson. See the on-screen User’s Guide for details.

Full Auto Mode

Home and Professional Mode

Epson Perfection V700 Photo/V750 Pro

10 - Epson Perfection V700 Photo/V750 Pro 12/05

Transporting the Scanner

Before transporting the scanner for a long distance or storing it

for an extended period of time, you need to lock the scanner’s

carriage and transparency unit to prevent damage.

1. Plug in the scanner, turn on the scanner using its power

button, and wait until the carriage moves to the home

position (near the cover hinge). While the scanner light is

green, turn off the scanner using its power button.

2. Open the scanner cover and slide the transparency unit

transportation lock to the locked position. Then close the

scanner cover.

3. Disconnect the scanner’s interface cable from your

computer.

4. Disconnect the scanner’s cover cable.

5. On the back of the scanner, slide the transportation lock to

the locked position to secure the scanner carriage.

6. Attach the protective materials that came with the scanner,

then repack the scanner in its original box or a similar box

that fits the scanner snugly.

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario