Epson PowerLite 50c Manual de usuario
S
T
A
R
T
H
E
R
E
EPSON®PowerLite®50c/70c
Quick Setup
Connect the power cord to your projector and plug the other end into a grounded outlet.
3Connect the other end to your laptop’s video or monitor port.
1Turn on the projector first. To do so, press the red Power button.
The power light flashes green as the projector warms up,
and the projection lamp comes on in about 30 seconds.
2Turn on or restart your laptop. (Windows®only: If you see a
New Hardware Wizard screen, click Cancel.)
Turn Over
Press the red Power button twice, then let the projector cool while the power light
flashes orange (about a minute). Once the light stops flashing and stays on, it’s safe to
unplug the projector.
Never unplug the projector when the power light is green or flashing orange.
Locate everything
you’ll need
Plug in your projector
Turn on your equipment
Caution: Before unplugging the projector...
For most setups, you’ll need just these two cables:
You won’t need to install any software.
Power
Help
?
1
2
Make sure your projector and laptop are turned off.
Connect one end of the computer cable to the
Computer port on the projector.
Connect the projector
to your laptop
power cord computer cable
Follow these instructions to connect the projector
to your laptop. To connect other devices, such as
a VCR or desktop PC, see your User’s Guide.
power button
power light
EPSON PowerLite 50c/70c
If you see a blank screen or the No Signal message
after turning on your laptop, check the following:
Make sure the power light is green and
not flashing and the lens cap is off.
Try turning off the laptop and restarting it.
If you’ve connected more than one computer and/or video source,
you may need to press the Source button on top of the projector.
(Allow a few seconds for the projector to sync up after pressing it.)
Adjust the image
1Remove the lens cap and rotate the focus ring
to sharpen the image.
If You See a Blank Screen
Press the function key that lets you display on an external monitor.
It may have an icon such as , or it may be labelled CRT/LCD.
You may have to hold down the Fn (function) key while pressing it.
(Allow a few seconds for the projector to sync up after pressing
the key.) Check your laptop’s manual or online help for details.
On most systems, the or CRT/LCD key let you toggle between
the LCD screen and the projector, or display on both at the same
time.
You might need to use the Display utility in the Control Panel
to enable both the LCD screen and external monitor port.
If you’re using a Windows laptop:
If you’re using a Macintosh®:
CPD-11579
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.
Copyright © 2001 by Epson America, Inc. 1/01
2Raise the image as needed. To do this, pull up the blue foot
release levers and lift the front of the projector. Once the
image is positioned where you want it, release the levers
to lock the feet in position.
3If your image looks like or , you’ve placed the projector
at an angle to the screen. Move it directly in front of the
center of the screen, facing the screen squarely.
4If your image looks like or , press the + or – side of
the Keystone button to correct the shape of the image.
EPSON PowerLite 50c/70c
Note: If you see a blank screen after focusing,
see the box below.
1. From the Apple menu, select Control Panels, then click Monitors
and Sound.
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other. This lets you display
on the projector screen as well as the LCD screen.
If this option isn’t available, you may need to select one of the
Simulscan resolution settings:
1. Perform step 1 above, if necessary.
2. Click the Monitor icon.
3. Select a Simulscan resolution as shown. (Allow a few seconds for
the projector to sync up after making the selection.)
focus ring
No signal
drag one monitor icon
on top of the other
click here
select a Simulscan
resolution
click here
No signal
EPSON PowerLite 50c/70c
If you see a blank screen or the No Signal message
after turning on your laptop, check the following:
Make sure the power light is green and
not flashing and the lens cap is off.
Try turning off the laptop and restarting it.
If you’ve connected more than one computer and/or video source,
you may need to press the Source button on top of the projector.
(Allow a few seconds for the projector to sync up after pressing it.)
Adjust the image
1Remove the lens cap and rotate the focus ring
to sharpen the image.
If You See a Blank Screen
Press the function key that lets you display on an external monitor.
It may have an icon such as , or it may be labelled CRT/LCD.
You may have to hold down the Fn (function) key while pressing it.
(Allow a few seconds for the projector to sync up after pressing
the key.) Check your laptop’s manual or online help for details.
On most systems, the or CRT/LCD key let you toggle between
the LCD screen and the projector, or display on both at the same
time.
You might need to use the Display utility in the Control Panel
to enable both the LCD screen and external monitor port.
If you’re using a Windows laptop:
If you’re using a Macintosh®:
CPD-11579
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.
Copyright © 2001 by Epson America, Inc. 1/01
2Raise the image as needed. To do this, pull up the blue foot
release levers and lift the front of the projector. Once the
image is positioned where you want it, release the levers
to lock the feet in position.
3If your image looks like or , you’ve placed the projector
at an angle to the screen. Move it directly in front of the
center of the screen, facing the screen squarely.
4If your image looks like or , press the + or – side of
the Keystone button to correct the shape of the image.
EPSON PowerLite 50c/70c
Note: If you see a blank screen after focusing,
see the box below.
1. From the Apple menu, select Control Panels, then click Monitors
and Sound.
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other. This lets you display
on the projector screen as well as the LCD screen.
If this option isn’t available, you may need to select one of the
Simulscan resolution settings:
1. Perform step 1 above, if necessary.
2. Click the Monitor icon.
3. Select a Simulscan resolution as shown. (Allow a few seconds for
the projector to sync up after making the selection.)
focus ring
No signal
drag one monitor icon
on top of the other
click here
select a Simulscan
resolution
click here
No signal
EPSON PowerLite 50c/70c
If you see a blank screen or the No Signal message
after turning on your laptop, check the following:
Make sure the power light is green and
not flashing and the lens cap is off.
Try turning off the laptop and restarting it.
If you’ve connected more than one computer and/or video source,
you may need to press the Source button on top of the projector.
(Allow a few seconds for the projector to sync up after pressing it.)
Adjust the image
1Remove the lens cap and rotate the focus ring
to sharpen the image.
If You See a Blank Screen
Press the function key that lets you display on an external monitor.
It may have an icon such as , or it may be labelled CRT/LCD.
You may have to hold down the Fn (function) key while pressing it.
(Allow a few seconds for the projector to sync up after pressing
the key.) Check your laptop’s manual or online help for details.
On most systems, the or CRT/LCD key let you toggle between
the LCD screen and the projector, or display on both at the same
time.
You might need to use the Display utility in the Control Panel
to enable both the LCD screen and external monitor port.
If you’re using a Windows laptop:
If you’re using a Macintosh®:
CPD-11579
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.
Copyright © 2001 by Epson America, Inc. 1/01
2Raise the image as needed. To do this, pull up the blue foot
release levers and lift the front of the projector. Once the
image is positioned where you want it, release the levers
to lock the feet in position.
3If your image looks like or , you’ve placed the projector
at an angle to the screen. Move it directly in front of the
center of the screen, facing the screen squarely.
4If your image looks like or , press the + or – side of
the Keystone button to correct the shape of the image.
EPSON PowerLite 50c/70c
Note: If you see a blank screen after focusing,
see the box below.
1. From the Apple menu, select Control Panels, then click Monitors
and Sound.
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other. This lets you display
on the projector screen as well as the LCD screen.
If this option isn’t available, you may need to select one of the
Simulscan resolution settings:
1. Perform step 1 above, if necessary.
2. Click the Monitor icon.
3. Select a Simulscan resolution as shown. (Allow a few seconds for
the projector to sync up after making the selection.)
focus ring
No signal
drag one monitor icon
on top of the other
click here
select a Simulscan
resolution
click here
No signal
Otros manuales para PowerLite 50c
5
Tabla de contenidos
Otros manuales de Proyector de Epson
Epson
Epson PowerLite Pro G5750WU Manual de usuario
Epson
Epson EB-L255F Manual de usuario
Epson
Epson G5000 - PowerLite XGA LCD Projector Guía de referencia
Epson
Epson PowerLite 420 Hoja de especificaciones
Epson
Epson PowerLite S1 Manual de instalación y operación
Epson
Epson PowerLite Pro Cinema 4040 Manual de usuario
Epson
Epson PowerLite Home Cinema 8350 Manual de usuario
Epson
Epson 1735W - PowerLite WXGA LCD Projector Manual de usuario
Epson
Epson PowerLite Home Cinema 5030UB Manual de usuario
Epson
Epson dreamio EMP-TWD1 Manual de usuario
Epson
Epson Pro L1060W Manual de usuario
Epson
Epson EB-93 Manual de usuario
Epson
Epson V11H181020SC - MovieMate 25 WVGA LCD... Dimensiones
Epson
Epson VS350W Hoja de especificaciones
Epson
Epson PowerLite 420 Guía de referencia
Epson
Epson PowerLite 95 Manual de usuario
Epson
Epson PowerLite Cinema 500 Manual de usuario
Epson
Epson EMP-703 Manual de usuario
Epson
Epson EH-LS800W Manual de usuario
Epson
Epson BrightLink 695Wi Manual de usuario
Manuales populares de Proyector de otras marcas
iEmmet
iEmmet MP-312 Manual de usuario
Sony
Sony VPL-HS10 Marketing Specifications & Features Manual de usuario
Sony
Sony VPL-HW65ES Manual de servicio
Toshiba
Toshiba TLP-791U Manual de usuario
Philips
Philips LC1341 Guía de referencia
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario
