Epson Elp-3000 Manual de usuario
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means, electronic, mechanical, photocopying, recording,
or otherwise, without the prior written permission of Seiko Epson Corporation. No patent
liability is assumed with respect to the use of the information contained herein. Neither is any
liability assumed for damages resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shah be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by purchaser or third
parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications,
repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with
Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the
use of any options or any consumable products other than those designated as Original EPSON
Products or EPSON Approved Products by Seiko Epson Corporation.
EPSON is a registered trademark of Seiko Epson Corporation.
EPSON Connection is a service mark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may
be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 1995 by Epson America, Inc.
4003816-01
Torrance, California, USA
3/24/95
ii
Introduction
vii
Getting the Most Out of Your Projector
Optional Accessories
About This Manual
Safety Instructions
Where to Get Help
CompuServe online support
1 Installation
Unpacking the Projector
Additional components
Setting Up the Projector
Connecting to a Computer
Connecting to a PC desktop computer
Connecting to a PC laptop computer
viii
X
Xi
Xii
xiv
xv
1
2
3
4
6
7
8
Contents
111
Connecting to a desktop Macintosh
9
Connecting to a PowerBook
10
Connecting to a Video Source
11
Connecting to an Audio Source
13
Connecting to an External Speaker or PA System
14
Setting Up Serial Communication
15
Connecting the serial cable
15
Installing the software
16
Connecting the Remote Control with the Lead Wire
17
2 Using the Projector
Turning the Equipment On and Off
Focusing
and
Positioning the Screen Image
Controlling the Projector
Adjusting the settings from ELP Link
Monitoring the Projector
Using Rear Projection
3 Using the Menus
29
Accessing the Menus
30
Changing menu settings
31
Accessing ELP Link menus
32
Restoring the default settings
33
Menu Settings
33
Computer menu
34
19
20
21
23
26
27
28
iv
Contents
Video menu
36
Display menu
37
Audio menu
39
Options menu
40
Custom menu
41
4
Remote Control of the Computer
43
ELP Remote Programmer Templates
44
Starting the ELP Remote Programmer
45
Assigning a Macro to a Programmable Button
48
Using record mode
49
Using manual mode
51
Activating a Template
51
ELP Remote Programmer Menus
52
5 Maintenance
Cleaning the Lens
54
Cleaning the Projector Case
54
Cleaning the Air Filter
54
Cleaning the Trackball
56
Replacing the Lamp
58
Replacing the Fuse
61
Contents
53
V
Introduction
T
he
compact, lightweight EPSON” ELP-3000 Projector allows you to project
computer images and video onto a large screen for full-color presentations. The
projector can connect simultaneously to two image sources; one can be your PC
or Apple” Macintosh’ computer and the other can be a video source, such as a
VCR, camcorder, digital camera, or laser disk player. Audio can be supplied with
one or both image sources.
Images are displayed in up to 16 million colors at a resolution of 640 x 480
pixels. The projector’s 250-lumen bulb produces bright images that can be easily
seen in rooms light enough to take notes. You can play audio on the projector’s
internal speakers or route it to an external speaker for amplification. You control
the projector through a hand-held remote control, which allows you to switch
between image sources and make adjustments to the projected image.
The projector supports any computer capable of VGA output, including IBM
®
-
compatible PCs and laptops and Apple Macintosh computers, including the
PowerBook™ and Power Macintosh.” The video source can be NTSC, PAL,
and SECAM in composite video or S-Video format.
vii
Getting the Most Out of Your Projector
The projector comes with a full set of features that allow you to control the
settings for the image display, video, and audio. To get the most out of your
projector, read this section for a quick summary of the important features.
Remote control
The buttons on the remote control allow you to directly change the volume,
control the brightness, or switch from one image source to the other. Additional
adjustments can be made by using the buttons on the remote control to access
the projector’s menu system.
The menus, which you can superimpose on the projector image or display on
your computer screen, allow you to do the following:
l
Control the brightness, contrast, sharpness, color, and position of the image.
l
Adjust the volume, balance, treble, and bass settings.
l
Adjust the display by rotating or inverting it.
Additional settings are described in Chapter 3.
You can also use the remote control to control your computer if you install the
Serial Communication Kit.
viii
Introduction
Serial Communication Kit
The Serial Communication Kit allows your computer and projector to communi-
cate over an RS-232C connection. The kit includes an RS-232C serial cable and
two software utilities: ELP Link and ELP Remote Programmer.
l
ELP Link allows you to make adjustments to the projector from your computer.
The same controls that are available on your remote control, including the
ability to access the projector menus, are available from the main ELP Link
screen.
l
The ELP Remote Programmer allows you to use the remote control to control
your computer. The trackball moves the mouse on your computer monitor, and
five buttons on the remote control can be programmed to drag or click
windows and icons or perform the same functions as keys on your keyboard.
For information on using ELP Link, see Chapters 2 and 3. For information on the
ELP Remote Programmer, see Chapter 4.
Standby mode
Standby mode conserves electricity by automatically turning off the lamp if the
projector has not been used for a specified period of time (the default is
10
minutes). In standby mode, the projector remains on but the lamp is turned
off. This conserves electricity, cools the projector, and extends the life of the lamp.
Use the Standby button on the remote control to turn standby mode on or off.
Getting the Most Out of Your Projector
ix
Otros manuales para Elp-3000
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Proyector de Epson
Epson
Epson 830p - PowerLite XGA LCD Projector Manual de usuario
Epson
Epson VS400 Guía de referencia
Epson
Epson PowerLite 5500c Manual de usuario
Epson
Epson EH-TW420 Manual de usuario
Epson
Epson EMP-745 Manual de usuario
Epson
Epson 821p - PowerLite XGA LCD Projector Manual de usuario
Epson
Epson EMP 400W Manual de usuario
Epson
Epson EX7210 Manual de usuario
Epson
Epson PowerLite 720c Manual de usuario
Epson
Epson PowerLite 76c Manual de usuario
Epson
Epson EB X6 Manual de usuario
Epson
Epson EB-1720 Manual de usuario
Epson
Epson EB-L25000U Manual de uso y cuidado
Epson
Epson PowerLite Cinema 500 Manual de usuario
Epson
Epson PowerLite Pro G6170 Manual de usuario
Epson
Epson PowerLite 84 Manual de usuario
Epson
Epson PowerLite 5000 Manual de usuario
Epson
Epson RS-353 Manual de usuario
Epson
Epson PowerLite 9300i Hoja de especificaciones
Epson
Epson 830p - PowerLite XGA LCD Projector Manual
Manuales populares de Proyector de otras marcas
iEmmet
iEmmet MP-312 Manual de usuario
Sony
Sony VPL-HS10 Marketing Specifications & Features Manual de usuario
Sony
Sony VPL-HW65ES Manual de servicio
Toshiba
Toshiba TLP-791U Manual de usuario
Philips
Philips LC1341 Guía de referencia
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario
