Epson BrightLink 695Wi+ Manual de usuario

Touch Unit and Control Pad

Installation Guide

Guide d’installation de l’unité tactile

et du boîtier de commande

CPD-50949R1

Printed in XXXXXX

Pays d’impression : XXXXXX

Touch Unit and Control Pad

Installation Guide

About This Installation Guide

This guide describes how to mount the Touch Unit and Control Pad for use with your Epson® projector.

The following projectors are covered by this guide:

•BrightLink® 695Wi/695Wi+/696Ui/697Ui/710Ui

•BrightLink Pro 1450Ui/1460Ui/1470Ui

Your projector may differ from the illustrations in this guide, but the instructions are the same.

The Control Pad is included with the BrightLink 697Ui and BrightLink Pro 1450Ui/1460Ui/1470Ui. The Control

Pad should only be connected to these products. Do not connect the Control Pad to any other projectors.

Safety Instructions

For your safety, read all the instructions in this guide before using the Touch Unit and Control Pad. Incorrect

handling that ignores instructions in this guide could damage the wall mount or could result in personal

injury or property damage. Keep this installation guide on hand for future reference.

Read the safety instructions in the User's Guide for your projector and follow the instructions in this document.

Explanation of Symbols

The warning marks shown below are used throughout this installation guide to prevent personal injury or

property damage. Make sure you understand these warnings when reading this installation guide.

Safety Precautions for Installation

This symbol indicates information that, if ignored, could possibly result in personal injury or even death

due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical

damage due to incorrect handling.

This symbol indicates related or useful information.

Symbol indicating an action that must not be done

Symbol indicating an action that should be done

Follow the instructions in this guide to install and operate the Touch Unit.

If the Touch Unit is not installed and operated properly, the light emitted from the laser could cause injury to

eyesight.

When you mount the projector on the wall with the wall mount, the wall must be strong enough to hold the

projector, the wall mount, as well as the Control Pad and the Touch Unit, if necessary.

The wall mount should be installed on a concrete wall. Confirm the weight of the projector, the wall mount,

the Control Pad, and the Touch Unit before installation, and maintain the strength of the wall. If the wall is

not strong enough, reinforce the wall before installation.

Never modify the Control Pad or Touch Unit.

Warning

Caution

Warning

English

Installation Location

•The projector must be installed in one of the following locations in order for the Touch Unit to function

properly:

•Mounted on a wall or suspended from the ceiling with images projected from in front of the screen.

•Mounted vertically on a table with images projected from the front of the table.

•Before installing the Touch Unit, verify that the installation location meets the following conditions:

•The Touch Unit can be secured to the surface with magnets or screws, or the included Touch Unit

Bracket.

•The surface is flat, smooth, and unwarped with no more than 0.2 inch (5 mm) of unevenness in any

direction on the screen surface.

When performing wiring, make sure the cable does not come into contact with any screws or bolts.

Handling the cable incorrectly may cause fire or electric shock.

Do not apply optical devices such as a magnifying glass or telescope to the laser light diffused from the

Touch Unit.

If such optical devices are applied, it could cause personal injury or fire.

Do not look into the Touch Unit’s laser diffusion ports.

This could cause injury to eyesight. Extra care should be taken when children are present.

Do not view the laser light using optical devices such as a magnifying glass within a range of 2.75 inches

(70 mm).

Viewing at close range could cause injury to eyesight.

Connect the Touch Unit to BrightLink 695Wi/695Wi+/696Ui/697Ui/710Ui and BrightLink Pro 1450Ui/

1460Ui/1470Ui models only. Do not connect it to any other projectors or devices.

Do not use the Touch Unit if you are using or near medical equipment such as a pacemaker.

The magnet within the Touch Unit generates electromagnetic interference which could cause medical equipment

to malfunction.

Keep magnetic storage media (for example, magnetic cards or electronic devices such as computers,

digital watches, or cell phones) away from the Touch Unit.

The magnet within the Touch Unit generates electromagnetic interference which could corrupt data or cause the

media or device to malfunction.

Warning

Caution

0.2 in. (5 mm)

•When installing the Touch Unit within the frame of the whiteboard, secure the Touch Unit with magnets

or screws.

Make sure there are no obstacles, such as cables, or protruding objects such as whiteboard trays, pen

holders, or thick frames in the shaded areas in the following figure. The Touch Unit will not operate

correctly if anything is obstructing the infrared signal.

•When installing the touch unit above the frame of a whiteboard, use the included Touch Unit Bracket.

•If the distance from the wall to the surface of the whiteboard is greater than 2 inches (51 mm), you

must install the Touch Unit on the whiteboard.

•If the frame of the whiteboard extends more than 0.1 inch (3 mm) away from the board surface, you

must install the Touch Unit on the whiteboard or screen.

0.8 in. (20 mm)

4.0 in. (100 mm)4.0 in. (100 mm)

English

1Package Contents 6

2Specifications 7

3Installing the Touch Unit

Installing the Touch Unit above a whiteboard

Turn on the projector

Display the installation pattern

Remove the dial cover

Determine the installation position for the Touch Unit Bracket

Install the Touch Unit Bracket

Connect the cable

Adjust the angle

Attach cover

Installing the Touch Unit on a whiteboard

Turn on the projector

Display the installation pattern

Remove the dial cover

Determine the installation position for the Touch Unit

Install the Touch Unit

Connect the cable

Adjust the angle

Attach labels

Attach cover

4Installing the Control Pad (BrightLink 697Ui and

BrightLink Pro 1450Ui/1460Ui/1470Ui)

Check the installation location

Remove the front cover

Attach the Control Pad

Connect the projector cables to the Control Pad

Attach the port protection stickers

Attach the front cover

5Appendix

Using the Easy Interactive Function

Attaching a Security Cable

1 Package Contents

Touch Unit

The following parts are packaged with your projector and are necessary when attaching the Touch Unit. When

installing the Touch Unit on a non-magnetic screen or whiteboard, you will also need three M4 screws.

Touch Unit Bracket

The following parts are packaged with your projector and are necessary when attaching the Touch Unit above

the frame of a whiteboard. When installing the installation plate, you will also need three (3) M4 wood screws

or M4 anchor bolts (not included).

Tape (approx. 2.4 inches

[6 cm]) for securing the

markers (×12)

Label (×4)

Touch Unit

Touch Unit connection cable Infrared deflector (approx.

11.2 inches [28.5 cm]) (×8)

Spacer for screw hole (×3)

Marker (x2)

Installation plate

M4 × 12 mm hexagon

socket head cap bolt (×2)

M4 × 25 mm hexagon

socket head cap bolt (×2)

Securing plate

M4 × 55 mm and M4 × 70 mm

hexagon socket head cap bolts

English

Control Pad (BrightLink 697Ui and BrightLink Pro 1450Ui/1460Ui/1470Ui)

The following parts are packaged with your projector and are necessary when attaching the Control Pad.

When installing the Control Pad on a wall, you will also need four commercially available M4 × 20 mm screws.

2 Specifications

Touch Unit

External dimensions and weight

The Touch Unit weighs approximately 16 ounces (450 g).

Attached labels

The Touch Unit is a Class 1 laser product that conforms to the JIS C 6802:2011 standard. There are warning

labels affixed to the Touch Unit to indicate that it is a Class 1 laser product. The labels contain the following

information:

•Invisible laser radiation

•Do not view the beam directly with optical instruments

•Class 1 laser product

Port protection

stickers

Control Pad

Pen stand Stereo mini

connection cable

8.3 in. (210 mm)

3.7 in. (95 mm)

2.0 in.

(51 mm)

Laser diffusion port

The laser beam is diffused from the laser diffusion ports on the back of the Touch Unit.

Control Pad

External dimensions and weight

The Control Pad weighs approximately 8.2 ounces (262 g).

5.4 in (135.9 mm)

0.6 in

(15.47 mm)

0.1 in

(3.5 mm)

1.1 in

(29 mm)

4.2 in (107 mm)

1.9 in (47 mm)

1.2 in

(30.9 mm)

6.0 in (153.5 mm)

0.4 in

(11.5 mm)

4.3 in (109 mm)

4.4 in (111 mm)

2.5 in (63.3 mm)

2.0 in (51.5 mm)

English

Cable routing holes

When routing cables through a wall, use the position ( ) in the following figure as the cable routing hole.

Otherwise, remove the cable cover ( ) and route the cables through the opening. Route the printer cable

along the groove on the back of the Control Pad.

Pen stand external dimensions and weight

The pen stand weighs approximately 3.3 ounces (93 g).

4.0 in (101.9 mm)

1.7 in

(44.4 mm)

1.4 in

(35.5 mm)

2.8 in (70 mm)

1.4 in

(36 mm)

3.9 in (99.9 mm)

1.1 in

(28.8 mm)

1.1 in

(28.8 mm)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Proyector de Epson

Epson

Epson EB-G5950 Manual de usuario

Epson

Epson VS410 Guía de referencia

Epson

Epson Megaplex MG-50 Manual de usuario

Epson

Epson ELPWT01 Manual de usuario

Epson

Epson PowerLite 400W Manual de usuario

Epson

Epson PowerLite 7350 Manual de usuario

Epson

Epson EB-1795F Manual de usuario

Epson

Epson EB-485Wi Manual de usuario

Epson

Epson Home Cinema 880 Manual de usuario

Epson

Epson EB-L570U Manual de usuario

Epson

Epson BrightLink 450Wi - Interactive Projector Guía

Epson

Epson PowerLite 8300i/NL Hoja de especificaciones

Epson

Epson EX7220 Manual de usuario

Epson

Epson EMP-X52 Manual de usuario

Epson

Epson Elmo HV-110XG Dimensiones

Epson

Epson PowerLite 4300 Instrucciones de funcionamiento y seguridad

Epson

Epson V11H257220 - MovieMate 72 LCD Projector Manual de usuario

Epson

Epson PowerLite Home Cinema 2000 Manual de usuario

Epson

Epson EB-S8 Manual de usuario

Epson

Epson EMP-820 Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Epson

Epson EH-TW5950 Manual de usuario

Epson

Epson PowerLite EMP-1810 Manual de usuario

Epson

Epson PowerLite 9100i Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario

Asus

Asus ZenBeam Latte Manual de usuario

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Manual de usuario

JVC

JVC 1108TTH-AO-AO Manual de usuario