Epson WorkForce AL-MX200DNF Instrucciones originales

Safety Information Guide

NPD4757-00

Safety Instructions

Warning, Caution, Important, and Note

Warning

must be followed to avoid serious bodily injury.

Caution

must be followed carefully to avoid bodily injury.

Important

must be observed to avoid damage to your equipment.

Note

contains important information and useful tips on the operation of your printer.

Important Safety Instructions

Setting up the printer

❏Be sure to lift the printer by the correct positions as shown below.

❏When moving the printer, always keep it horizontal.

AL-MX200 Series Safety Information Guide

Safety Instructions 2

❏If you are unable to insert the AC plug into the electrical outlet, contact an electrician.

❏Be sure the AC power cord meets the relevant local safety standards. Use only the power cord that

comes with this printer. Use of the another cord may result in fire or electric shock. This printer’s

power cord is for use with this printer only. Use with other equipment may result in fire or electric

shock.

❏Ifdamageoccurstotheplug,replacethecordsetorconsultaqualified electrician. If there are fuses

in the plug, make sure you replace them with fuses of the correct size and rating.

❏Use a grounded outlet that matches the printer’s power plug. Do not use an adapter plug.

❏Avoid using an electrical outlet that is controlled by wall switches or automatic timers. Accidental

disruption of power can erase valuable information in your computer’s and printer’s memory.

❏Make sure that there is no dust on the socket.

❏Be sure to insert the plug completely into the electrical outlet.

❏Do not handle the plug with wet hands.

❏Unplug this printer from the wall outlet and refer servicing to a qualified service representative

under the following conditions:

A When the power cord or plug is damaged or frayed.

B If liquid has been spilled into it.

C If it has been exposed to rain or water.

D If it does not operate normally when the operating instructions are followed. Adjust only those controls that

arecoveredbythe operatinginstructionssinceimproperadjustmentof other controlsmayresult in damage

and will often require extensive work by a qualified technician to restore the printer to normal operation.

E If it has been dropped or the cabinet has been damaged.

F If it exhibits a distinct change in performance, indicating a need for service.

❏Avoid sharing outlets with other appliances.

❏Connect all equipment to properly grounded power outlets. Avoid using outlets on the same

circuit as photocopiers or air control systems that regularly switch on and off.

❏Connect your printer to an electrical outlet that meets the power requirements of this printer.

Your printer’s power requirements are indicated on a label attached to the printer. If you are not

sure of the power supply specifications in your area, contact your local power company or consult

your dealer.

AL-MX200 Series Safety Information Guide

Safety Instructions 3

❏If you use an extension cord, make sure that the total of the ampere ratings on the products

plugged into the extension cord does not exceed the extension cord ampere rating.

❏When connecting this printer to a computer or other device with a cable, ensure the correct

orientation of the connectors. Each connector has only one correct orientation. Inserting a

connector in the wrong orientation may damage both devices connected by the cable.

Finding the place for the printer

When relocating the printer, always choose a location that has adequate space for easy operation and

maintenance. Use the following illustration as a guide for the amount of space required around the

printer to ensure smooth operation.

a 10 cm

b 10 cm

c 19 cm

d 30 cm

e 19 cm

In addition to space considerations, always heed the following precautions when finding a place to

locate the printer:

❏Place the printer near an electrical outlet where you can easily plug in and unplug the power cord.

AL-MX200 Series Safety Information Guide

Safety Instructions 4

❏Do not put your printer where the cord will be stepped on.

❏Do not use printer in a damp environment.

❏Avoid locations that are subject to direct sunlight, excessive heat, moisture, oil vapor, or dust.

❏Do not place the printer on an unstable surface.

❏Slots and openings in the cabinet and the back or bottom are provided for ventilation. Do not

block or cover them. Do not put the printer on a bed, sofa, rug, or other similar surface or in a

built-in installation unless proper ventilation is provided.

❏Keep the entire computer and printer system away from potential sources of interference, such as

loudspeakers or the base units of cordless telephones.

❏Leave adequate room around the printer to allow for sufficient ventilation.

Using the printer

❏Becarefulnottotouchthefusing unit, whichis marked CAUTION, orthesurroundingareas. If the

printer has been in use, the fusing unit and the surrounding areas may be very hot. If you must

touchoneofthese areas, turn off the printerand wait 40 minutes to allowtheheat to subside before

doing so.

❏Do not insert your hand deep into the fusing unit as some components are sharp and may cause

injury.

❏Never push objects of any kind through cabinet slots as they may touch dangerous voltage points

or short out parts that could result in a risk of fire or electric shock.

❏Do not sit or lean on the printer. Do not put heavy objects on the printer.

AL-MX200 Series Safety Information Guide

Safety Instructions 5

❏Do not use any kind of combustible gases in or around the printer.

❏Never force the printer’s components into place. Although the printer is designed to be sturdy,

rough handling can damage it.

❏Do not leave jammed paper inside the printer. This can cause the printer to overheat.

❏Never spill liquid of any kind on the printer.

❏Adjust only those controls that are covered by the operating instructions. Improper adjustment of

other controls may result in damage and may require repair by a qualified service representative.

❏Do not turn off the printer:

- After turning on the printer, wait until the Data/Error light is on.

- While the Data/Error light is flashing.

- While printing.

❏Avoid touching the components inside the printer unless instructed to do so in this guide.

❏Do not expose the drum to room light for more than five minutes. Exposure to light can damage

the drum, causing dark or light areas to appear on the printed page and reducing the service life of

the drum.

❏Be careful not to scratch the surface of the drum. Avoid touching the drum, since oil from your

skin can permanently damage its surface and affect print quality.

❏Follow all warnings and instructions marked on the printer.

❏Except as specifically explained in the printer’s documentation, do not attempt to service this

printer yourself.

❏Periodically disconnect the plug from the electrical outlet and clean the blades.

❏Do not disconnect the plug while the printer is on.

❏If the printer will not be used for a long time, disconnect the plug from the electrical outlet.

❏Unplug this printer from the wall outlet before cleaning.

❏Use a well-wrung cloth for cleaning and do not use liquid or aerosol cleaners.

Handling consumable products

❏Do not burn used consumable products because they might explode and injure someone. Dispose

of them according to local regulations.

AL-MX200 Series Safety Information Guide

Safety Instructions 6

❏Be sure to keep consumable products out of the reach of children.

❏When handling a toner cartridge, always place it on a clean, smooth surface.

❏Do not attempt to modify a toner cartridge or take it apart.

❏Do not touch the toner. Always keep toner away from your eyes. If toner gets on your skin or

clothes, wash it off with soap and water immediately.

❏If toner is spilled, use a broom and dustpan or a damp cloth with soap and water to clean it up.

Becausethefine particlescancausea fireorexplosionif theycomeintocontact withaspark,do not

use a vacuum cleaner.

❏Wait at least one hour before using a toner cartridge after moving it from a cool to a warm

environment to prevent damage from condensation.

❏To get the best print quality, do not store the toner cartridge in an area subject to direct sunlight,

dust, salty air, or corrosive gases (such as ammonia). Avoid locations subject to extreme or rapid

changes in temperature or humidity.

❏Do not let the paper’s edge slide across your skin because the edge of the paper may cut you.

Safety Information

Ozone safety

Ozone emission

Ozone gas is generated by LED printers as a by-product of the printing process. Ozone is produced

only when the printer is printing.

Ozone exposure limit

The Epson LED printer generates less than 1.5 mg/h of continuous printing.

Minimize the risk

To minimize the risk of exposure to ozone, you should avoid the following conditions:

❏Use of multiple LED printers in a confined area

❏Operation in conditions of extremely low humidity

AL-MX200 Series Safety Information Guide

Safety Instructions 7

❏Poor room ventilation

❏Long, continuous printing together with any of the above

Printer location

The printer should be located so that the exhaust gases and heat generated are:

❏Not blown directly into the user’s face

❏Vented directly out of the building whenever possible

Standard and approvals

European model

AL-MX200DNF AL-MX200DWF

Low voltage directive 2006/95/EC EN60950-1 ✓✓

EMC directive 2004/108/EC EN55022 Class B ✓✓

EN61000-3-2 ✓✓

EN61000-3-3 ✓✓

EN55024 ✓✓

R&TTE directive 1999/5/EC EN300 328 - ✓

EN301 489-1 - ✓

EN301 489-17 - ✓

ETSI ES203 021 ✓✓

EN60950-1 ✓✓

For European users (AL-MX200DNF only)

We, Seiko Epson Corporation, hereby declare that the equipment model L722A is in compliance with

the essential requirements and other relevant provisions of Directive 1999/5/EC.

AL-MX200 Series Safety Information Guide

Safety Instructions 8

For use only in:

Ireland, United Kingdom, Austria, Germany, Liechtenstein, Switzerland, France, Belgium,

Luxembourg, Netherlands, Italy, Portugal, Spain, Denmark, Finland, Norway, Sweden, Iceland,

Cyprus, Greece, Slovenia, Bulgaria, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Poland,

Romania, Slovakia, Malta.

For European users (AL-MX200DWF only)

We, Seiko Epson Corporation, hereby declare that the equipment model L722B is in compliance with

the essential requirements and other relevant provisions of Directive 1999/5/EC.

For use only in:

Ireland, United Kingdom, Austria, Germany, Liechtenstein, Switzerland, France, Belgium,

Luxembourg, Netherlands, Italy, Portugal, Spain, Denmark, Finland, Norway, Sweden, Iceland,

Cyprus, Greece, Slovenia, Bulgaria, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Poland,

Romania, Slovakia, Malta.

Only indoor operation is permitted in France.

If used outside of own premises, general authorization is required in Italy.

Epson can not accept responsibility for any failure to satisfy the protection requirements resulting a

non-recommended modification of the products.

AL-MX200 Series Safety Information Guide

Safety Instructions 9

Sicherheitshinweise

Vorsicht, Achtung, Wichtig und Hinweis

Vorsicht

Anmerkungen dieser Art müssen beachtet werden, um schwere Körperverletzungen zu

vermeiden.

Achtung

Diese Warnungen müssen unbedingt beachtet werden, um Körperverletzungen zu vermeiden.

Wichtig

Anmerkungen dieser Art müssen beachtet werden, um Schäden am Gerät zu vermeiden.

Hinweis

enthält wichtige Informationen und hilfreiche Tipps zur Arbeit mit dem Drucker.

Wichtige Sicherheitshinweise

Aufstellen des Druckers

❏Der Drucker sollte entsprechend der im Folgenden beschriebenen Hebetechnik angehoben

werden.

AL-MX200 Series Safety Information Guide

Sicherheitshinweise 1

Otros manuales para WorkForce AL-MX200DNF

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Impresora de Epson

Epson

Epson LX-1310 Manual de usuario

Epson

Epson Stylus Color 670 Manual de usuario

Epson

Epson Stylus SX445W Instrucciones de montaje

Epson

Epson TM-C3500 Series Manual de uso y cuidado

Epson

Epson TM-P60II Manual de usuario

Epson

Epson R280 - Stylus Photo Color Inkjet Printer Manual de instrucciones

Epson

Epson LabelWorks LW-Z5010 Series Manual de uso y cuidado

Epson

Epson PM-400 Manual de instrucciones

Epson

Epson U925 - TM B/W Dot-matrix Printer Manual de usuario

Epson

Epson PictureMate PictureMate Manual de usuario

Epson

Epson LQ-1150II Manual de instrucciones

Epson

Epson R200 - Stylus Photo Color Inkjet Printer Guía de instalación

Epson

Epson LQ-510 Guía de referencia rápida

Epson

Epson L7160 Series Manual de usuario

Epson

Epson Stylus Color C60 Manual de usuario

Epson

Epson Stylus Color C60 Manual de usuario

Epson

Epson ET-5850U Manual de usuario

Epson

Epson TM-T88III series Manual de usuario

Epson

Epson FX-80 Manual de usuario

Epson

Epson FX-880 - Impact Printer Manual de usuario

Epson

Epson Stylus PHOTO 1290 Manual de usuario

Epson

Epson GREENSTAR HEATSLAVE II EXTERNAL 25/32 Dimensiones

Epson

Epson EPL-N3000 Manual de usuario

Epson

Epson C284999 - TM H6000P B/W Direct Thermal Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario

IRA3D

IRA3D POETRY4 Manual de usuario

Ricoh

Ricoh Aficio AP400 Manual de usuario

BIXOLON

BIXOLON SRP-352plusV Manual de usuario