Epson SureColor P800 Manual de usuario
Screen Print Edition
What’s Included
The following items are included with the Screen Print Edition of your product:
■Epson®Screen Positive Film (1 roll)
■AccuRipTM Black Pearl SE RIP Software welcome card
■Roll paper holders (SureColor®P800 only)
Setting up your Screen Print printer
Step 1: Set up your printer and load the film
Set up your printer using the directions in the printer’s documentation.
Note: Wear gloves while handling the Screen Positive film to avoid getting smudges or
fingerprints on the film.
Loading the Screen Positive film (SureColor T3270)
Load the film roll using the directions for roll paper installation in the online User
Guide.
Loading the Screen Positive film (SureColor P800)
Attach the roll paper unit and load the film roll onto the roll spindle using the
directions in the online User’s Guide. Then follow the steps below to load the film into
the printer.
1. Open the front cover of the printer and extend the first section of the output tray.
2. Open the rear support, but do not pull out the extension.
3. On the touch screen, navigate to Setup > System Administration > Printer
Setting and change the Paper Size Check setting to Off.
4. Load the film roll in the roll paper unit with the grey flange on the left-hand side.
5. Feed the film into the printer until it stops, then hold the film in place. Press
Load on the touch screen to pull the film into the printer.
6. Check the touch screen and make sure the Paper Size is correct and that the
Paper Type is set to Premium Luster, then click OK.
7. Open the top cover and look inside. You see the edge of the film on the back side
of the opening. Gently push the film roll forward so that the leading edge of the
film contacts the front feed rollers. Do not bend or bow the film; apply just
enough pressure to move the film forward.
Step 2: Install the printer software and driver
Install the printer driver and software using the instructions that came with your
printer. Make sure you install the Software Updater utility and run it to download the
latest driver and firmware for your printer.
Step 3: Install the RIP software
Visit the following URL to download the AccuRIP Black Pearl SE RIP software:
softwareforscreenprinters.com/welcomese
Set up an account using the SE verification code on the AccuRIP welcome card and
the serial number on the back of your printer, then download and install the software.
Configuring the AccuRIP software
When using the Configuration Wizard to configure the AccuRIP Black Pearl SE
software, make sure the following settings are selected:
After configuring the software, follow the prompts to run a test print to ensure proper
communication between the software and the printer.
Setting Recommended value
Printer Epson SC-P800 Series
Epson SC-T3200 Series
Media Type Roll or Sheet
Size (roll) SureColor P800: 17”
SureColor T3270: 17”, 24”, or 36”
Size (sheet) Letter (8.5” × 11”)
13” × 19”
Configuring the printer driver
If you use the Epson printer driver instead of the AccuRIP software, you need to make
some adjustments to the driver settings. (The AccuRIP software is pre-configured to
work with Screen Positive film.)
*SureColor T3270: To ensure optimal quality and registration between film sets, it is recommended
that you perform a manual paper feed adjustment on the printer control panel when using Epson
Screen Positive Film for the first time.
Ordering additional film
You can order additional rolls or sheets of Epson Screen Positive film from
www.epsonstore.com.
Option Recommended setting
Media Type SureColor P800: Photo Paper > Premium Luster
SureColor T3270: Photo Paper > Premium Luster Photo Paper (260)
Ink SureColor P800: Photo Black Ink
SureColor T3270: Photo Black (automatically determined)
Color (SureColor P800) B&W
Mode (SureColor P800) Off (No Color Management)
Print Mode (SureColor T3270) Color/B&W Photo
Color Mode (SureColor T3270) Off (No Color Management)
Output Resolution 2880 × 1440 (Max Quality / Level 5)
MicroWeave On
High Speed Off (deselected)
Color Density SureColor P800: +15
SureColor T3270: +50
Drying Time 0
Paper Feed Adjust 0*
Paper Thickness 1
Platen Gap SureColor P800: Standard
SureColor T3270: Auto
Roll Paper Back Tension SureColor P800: N/A
SureColor T3270: Auto
Send 16-bit Data (OS X only) Off (deselected)
Epson Screen Positive Film (5 mil) Part number
17” × 100’ roll S450132
24” × 100’ roll S450133
8.5 × 11-inch sheets (100 pack) S450135
13 × 19-inch sheets (100 pack) S450136
EPSON and SureColor are registered trademarks of Seiko Epson Corporation.
AccuRIP is a trademark of Freehand Graphics.
OS X is a trademark of Apple, Inc., registered in the U.S. and other countries.
General Notice: Other product names used herein are for identification purposes only and may be
trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2016 Epson America, Inc., 2/16
CPD-50903
Printed in USA
Otros manuales para SureColor P800
3
Tabla de contenidos
Otros manuales de Impresora de Epson
Epson
Epson l300 Manual de usuario
Epson
Epson 1400 - Stylus Photo Color Inkjet Printer Manual de operación y mantenimiento
Epson
Epson EPL 5800 - B/W Laser Printer Manual de usuario
Epson
Epson A381H Guía de configuración
Epson
Epson L566 Manual de usuario
Epson
Epson 11880 - Stylus Pro Color Inkjet Printer Manual de usuario
Epson
Epson WorkForce Pro WP-4092 Manual de usuario
Epson
Epson Stylus Pro 9700 Series Manual de usuario
Epson
Epson TM-C610 Manual de usuario
Epson
Epson Stylus Office BX305F Guía del usuario
Epson
Epson Stylus Pro 7900 Instrucciones de montaje
Epson
Epson SecurColor TM-C3400 Manual de usuario
Epson
Epson EPL-N2010 Manual de usuario
Epson
Epson TM-T83II Manual de usuario
Epson
Epson TM-DT Series Manual de usuario
Epson
Epson ET-M16600 Series Manual de instrucciones
Epson
Epson LX-1170 Manual de usuario
Epson
Epson SC-S80600L Series Manual de usuario
Epson
Epson Subli-Print 4450 Manual de usuario
Epson
Epson 850N Manual de usuario
