Epson Stylus Pro 7400 Manual de operación y mantenimiento
NOTICE SHEET
About installing the printer software
In the Installing the Printer Software section of the Setup Guide, the step “Select Local or Network.” is
not necessary. Skip step 5 (For Windows) or step 6 (For Mac OS 9.x and Mac OS X).
About paper margin
In the Control Panel and Product Information section of the Reference Guide, the supported paper margins
are incorrect. The correct paper margins should be DEFAULT, T/B 15 mm,
T/B 25 mm, 15 mm, and 3mm.
The following table shows the default paper margin for the paper.
Note:
❏When you set the margin once, the margin applies to all media. To change the paper margin, select the target
margin setting again.
❏Try T/B 25 mm when smear may result in the top and bottom areas.
When you select the paper margin setting except DEFAULT, the following number appears on the right
side of the paper mark on the printer’s control panel.
Margin settings Top Bottom Left/Right
DEFAULT See the list below. 3 mm
T/B 15 mm 15 mm 15 mm 3 mm
T/B 25 mm 25 mm 25 mm 3 mm
15 mm 15 mm 15 mm 15 mm
3mm 3 mm 3 mm 3 mm
Roll Paper Top/Bottom Left/Right
Plain Paper
Singleweight Matte Paper
Enhanced Matte Paper
Premium Semimatte Photo Paper (250)
Premium Luster Photo Paper (250)
Photo Paper Gloss 250
Photo Glossy Paper
Photo Semigloss Paper
Textured Fine Art Paper
UltraSmooth Fine Art Paper
Proofing Paper Semimatte
15 mm 3 mm
Premium Glossy Photo Paper (250)
Premium Semigloss Photo Paper (250)
20 mm 3 mm
Margin settings Number
T/B 15 mm 1
T/B 25 mm 2
15 mm 1
3mm 0
Copyright © 2005 Seiko Epson Corporation. All rights reserved.
Printed in Japan 05. xx-xx
2
About Platen Gap
In the Control Panel section of the Reference Guide, the description about Platen Gap on the Custom Paper
menu is incorrect. WIDEST is not supported, so read it as below.
You can adjust the distance between the print head and paper. Normally, leave this set to STANDARD.
If you find that printed images are smeared, select WIDE. Select NARROW for printing on thin paper, or
WIDER for printing on thick paper.
Note:
❏There is also Platen Gap on the Printer Setup menu, but this one supports WIDEST. Only Platen Gap on the
Custom Paper menu does not support WIDEST.
❏The setting will return to STANDARD after you turn the printer on and off.
Cleaning the Printer
In the Maintenance and Transportation section of the Reference Guide, we have added some more
information for Cleaning the Printer, so read it as below.
To keep your printer operation in its top condition, clean it thoroughly if it becomes soiled.
wWarning:
Be careful not to touch the gears inside the printer.
cCaution:
❏Never use alcohol or thinners to clean the printer; these chemicals can damage the components as well
as the case.
❏Be careful not to get water on the printer mechanism or electronic components.
❏Do not use a hard or abrasive brush.
❏Do not spray the inside of the printer with lubricants; unsuitable oils can damage the mechanism.
Contact your dealer or a qualified service person if lubrication is needed.
1. Make sure the printer is turned off and all the lights are off, and then unplug the power cord. Leave
the printer for a minute.
cCaution:
Do not touch the following parts; otherwise, printouts may be soiled.
Roller
Ink absorption
Print head guide
3
2. Open the top cover and then use a soft, clean cloth to carefully remove any dust or dirt inside the
printer. Wipe the gray part by following the directions of the arrows.
If there is a serious problem of dirt on the inside of the printer, clean it using a soft, clean cloth
dampened with mild detergent. Then, wipe the inside of the printer dry with a dry, soft cloth.
3. If the back of a printout is soiled, carefully clean the platen (the gray part) using a soft, clean cloth.
4. If some powdery paper dust is stuffed in the platen, use something like a toothpick to remove it.
Close the top cover.
5. If the outer case is dirty, clean it using a soft, clean cloth dampened with mild detergent. Keep the
ink compartment covers closed to prevent water from getting inside.
4
About the Black Ink Conversion Kit
The Black Ink Conversion Kit is packed with the printer. Epson does not sell it as a consumable anymore.
Note:
Contact your dealer if the Black Ink Conversion Kit is needed.
Otros manuales para Stylus Pro 7400
2
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Impresora de Epson
Epson
Epson XP-6000 Manual de usuario
Epson
Epson ET-3843 Manual de usuario
Epson
Epson 1520 - Stylus Color Inkjet Printer Hoja de especificaciones
Epson
Epson PLQ-35 Manual de instrucciones
Epson
Epson Stylus C80WN - Ink Jet Printer Instrucciones de montaje
Epson
Epson 7800 - Stylus Pro Color Inkjet Printer Manual de usuario
Epson
Epson Stylus C62 Manual de usuario
Epson
Epson L6490 Series Manual de instrucciones
Epson
Epson LQ-1500 Manual de usuario
Epson
Epson TM-T88III series Manual de usuario
Epson
Epson FX-1050+ Dimensiones
Epson
Epson STYLUS 4001968 Manual de usuario
Epson
Epson WF-C21000 Instrucciones de funcionamiento
Epson
Epson ET-2750 series Guía del usuario
Epson
Epson WF-2860 Series Manual de usuario
Epson
Epson ProofPlus TM-H6000III Manual de usuario
Epson
Epson TM-T20II Manual de usuario
Epson
Epson Stylus Color C60 Manual de usuario
Epson
Epson SC-F9400H Series Manual
Epson
Epson DFX-5000+ Manual de usuario
