Epson Stylus Office TX600FW Series Guía
EPSON STYLUS OFFICE TX600FW
Wireless Printer Installation Guide
By using Wireless Router and Access Point
Installation Checklist:
Step 1: Confirm the computer has been connected to network. Check the SSID (Network
Name) and Passphrase (Security key and password).
Step 2: Setup the Wireless LAN on the printer panel.
Step 3: Confirm the connection status.
Step 4: Install the printer driver by Infrastructure mode
Before installation, please check the following information:
1. SSID (network name)
2. Type of Security Setting
Note: The printer supports WEP-64bit、WEP-128bit、WPA-PSK TKIP or WPA-PSK
AES only.
3. Security Key and Passphrase
Hints:
a. In order to protect your wireless network and data transmission, we recommend using a
security and encryption technologies with a particular SSID and security or Passphrase
to prevent intrusion from unknown users.
b. For any details information about wireless router and access point, please contact
Technical Hotline of those products directly.
Installation procedures:
Step 1: Confirm the computer has been connected to network. Check the SSID (Network
Name) and Passphrase (Security key and password).
(1) Confirm network setting:
SSID (Network Name)
Network Security Type
None
WEP-64bit
WEP-128bit
WPA-PSK TKIP
WPA-PSK AES
Note: If your security setting is not the below setting, please change your security setting
from Wireless Router or Access Point.
Security Key and Passphrase
Step 2: Setup the Wireless LAN on the printer panel
(1) After initialize, press 「 」bottom on printer panel, select “Setup”, then press 「OK」
button.
(2) Select “Network Setting” under “Setup”, then press 「OK」button.
(3) Select “Wireless LAN Setup” then press 「OK」button.
(4) LCD display shows the confirmation message, select “Yes”, then press 「OK」button.
(5) After enter “Wireless LAN Setup” menu, select “Enable”, then press 「OK」button.
(6) Select “Manual Wireless LAN setup” , then press 「OK」button.
(7) Press 「OK」button again to enter Setup page
(8) LCD display shows the Warning message, select “Yes” and then press 「OK」button.
(9) Select “Infrastructure Mode” under “Communication Mode Setup” Menu, then press
「OK」button.
(10) Select “SSID Input method”
10.1 Search SSID: Select the correct SSID
Hints:
A. If your SSID (your Network Name) cannot be shown, please check your Access Point
and Wireless Router.
B. If SSID is hidden as security issue, press「Back」button to return last step, and select
“Enter SSID”
Enter SSID: Enter the SSID manually
10.2 Security Setting: please select the same security setting as used for your access point or
wireless router.
10.3 For select WEP-64bit or WEP-128bit
If the character of WEP Key is 5 or 13, please select “Alphanumeric”.
If the character of WEP Key is 10 or 26, please select “Hexadecimal”.
10.4 Security Setting of WEP-64 bit: Enter 64-bit WEP key, then press 「OK」button.
(Press〝〞button to change character mode)
10.5 Security Setting of WEP-128bit: Enter 128-bit WEP key, then press 「OK」button.
(Press〝 〞button to change character mode)
10.6 For select WPA-PSK (TKIP) or WPA-PSK (AES)
Enter WPA passphrase (8-63 characters), then press「OK」button.
(Press〝 〞button to change character mode)
Hints: Please mind the “Capital Letter” and “Small Letter”, otherwise, it will affect the
connection.
Step 3: Confirm the connection status.
(1) Select “Confirm Network Settings” under “Network Settings” Menu, then press「OK」
button.
If you want to print status sheet, please press 「Start」button。
(2) If the printer is completed the network connections, the right top corner of LCD display
will show the following icon.
Already Connected to Wireless LAN network (Signal Strength: Excellent)
Already Connected to Wireless LAN network (Signal Strength: Medium)
Already Connected to Wireless LAN network (Signal Strength: Low)
If no icon is displayed, no connection and connection failure
Step 4: Install the printer driver by Infrastructure mode
(1) Insert CD disk into CD drive.
(2) Select language
(3) Select “Agree” and “Next”
(4) Recommend Choosing “Easy Install” and press “ Install”
Note: Although the software and driver have been installed successfully, the connection does
not configured well, so there is no icon displayed on “Printer and Fax”
Otros manuales para Stylus Office TX600FW Series
1
Tabla de contenidos
Otros manuales de Impresora de Epson
Epson
Epson Stylus Photo PX830FWD Manual de instrucciones
Epson
Epson U325 - TM B/W Dot-matrix Printer Manual de usuario
Epson
Epson WF-7211 Manual de usuario
Epson
Epson ET-2400 Manual de usuario
Epson
Epson LabelWorks LW-Z5000 Series Manual de usuario
Epson
Epson TM-T70II-DT Manual de uso y cuidado
Epson
Epson Stylus C84 Manual de usuario
Epson
Epson SC-T3000 Manual de usuario
Epson
Epson EPL-N2500 Instrucciones de instalación
Epson
Epson Stylus SX440W Instrucciones de montaje
Epson
Epson TM-T88III series Manual de servicio
Epson
Epson Aculaser M2300 Series Manual de usuario
Epson
Epson SC-T3700D Series Manual de usuario
Epson
Epson Stylus Photo 890 Manual de usuario
Epson
Epson XP-320 Manual de usuario
Epson
Epson 1520 - Stylus Color Inkjet Printer Manual de usuario
Epson
Epson SC-P600 series Manual de instrucciones
Epson
Epson SureColor SC-T7700D Manual de servicio
Epson
Epson FX-2180 - Impact Printer Manual de usuario
Epson
Epson B-308 Manual de usuario
