Epson Stylus Color 880 Manual de usuario

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

LProof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

Attaching the

Paper Support

Printing Your

First Page

Plugging

in the

Printer

Checking

the Printer

Connecting

the Printer

Installing the

Ink

Cartridges Installing the

Printer

Software

4012581-00

XXX

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

LProof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

Attaching the Paper Support

Insert the paper support into the slots at the rear of the printer.

Plugging in the Printer

Follow the steps below to plug in the printer.

1. Make sure that the printer is turned off. It is off when the2 power light

is off.

2. Check the label on the back of the printer to make sure that the voltage

required by the printer matches that of the electrical outlet that you will

be plugging it into. Also, make sure that you have the correct power

cable for your power source.

?Caution:

It is not possible to change the printer's voltage. If the rated voltage and

your outlet voltage do not match, contact your dealer for assistance. Do

not plug in the power cord.

3. If the power cord is not attached to the printer, connect it to the AC inlet

on the back of the printer.

4. Plug the power cord into a properly grounded electrical outlet.

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

Proof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

Connecting the Printer

If you have a PC, it is possible to connect to your printer using either the

parallel or the USB interface. A Macintosh can only be connected via the

USB interface. Depending on your geographic location, you may need to

acquire the appropriate cable. See “Options and Consumable Products” in

the Daily Use guide for details.

Note:

In order to connect your PC via the USB interface, your computer must be a

Windows 98 or Windows 2000 pre-installed model that is equipped with a USB

port.

Using the parallel interface for PCs

To connect the printer to your PC, you need a shielded, twisted-pair parallel

cable. Follow the steps below.

1. Make sure that both the printer and the computer are turned off.

2. Plug the cable connector

securely into the printer's

interface connector, then

squeeze the wire clips

together until they lock into

place on both sides. If your

cable has a ground wire,

connect it to the ground

connector below the interface

connector.

3. Plug the other end of the cable into the computer’s parallel interface. If

there is a ground wire at the computer end of the cable, connect it to the

ground connector at the back of the computer.

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

LProof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

Using the USB interface for Windows and Macintosh users

To connect the printer to a USB port, you need a standard, shielded USB

cable. Follow the steps below.

1. Make sure that both the printer and the computer are turned off.

2. Plug the appropriate end of the

cable into the USB port at the

back of the printer. (The shape of

the end that fits the printer

differs from that of the end that

fits the computer.)

3. Connect the other end of the

cable to the computer’s USB

port.

Installing the Printer Software

After connecting the printer to your computer, you must install the software

that is included on the “Printer Software for EPSON Stylus COLOR 880”

CD-ROM shipped with your printer.

Your printer software CD-ROM includes the following:

❏Printer driver and utilities

The printer driver runs, or “drives,” your printer; use it to make settings

such as print quality, speed, media type, and paper size. The Nozzle

Check, Head Cleaning, and Print Head Alignment utilities help you to

keep your printer in top operating condition. EPSON Status Monitor 3

(for Windows 98, 95, 2000, and NT 4.0) or EPSON StatusMonitor (for

Macintosh) notifies you of printer errors and displays printer status

information, such as the amount of ink remaining. The Status Monitor

also guides you through the ink replacement process.

❏Online guides

The online Reference Guide and the Color Guide help you to learn more

about your printer and color printing.

If you are using the floppy disk version of the software, make a backup copy

of the EPSON printer software disk before you begin installation. If you

wish to make a floppy disk version of the printer software, you can use the

driver disk creation utility that is included on the CD-ROM.

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

Proof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

Follow the instructions in the appropriate section below to install the printer

software. If you are DOS user, see “Printing with DOS” in the Daily Use

guide.

For Windows 98, 95, 2000, and NT 4.0 users

Windows 98, 95, 2000, and NT 4.0 users must first install the printer

software, and then, if you are connecting via the USB port, check to ensure

that the USB cable is correctly installed. If you are connecting via the parallel

port, proceed to section

after installing the software.

Installing the software

Follow the steps below to install the printer software.

1. Make sure that your printer is off.

2. Turn on your computer and start Windows. If the New Hardware

Found screen or any other Wizard appears, click Cancel.

3. Insert the printer software CD that is shipped with your printer in the

CD-ROM drive. The Installer dialog box opens. (For floppy disk users,

insert the disk in the disk drive and double-click the My Computer

icon, the floppy disk drive icon, and then Setup.exe.)

4. Select Install Printer Driver/Utility

and click . Then, click OK in the

dialog box that appears to start the

printer software installation.

Note:

It is possible to install the Reference

Guide on your hard drive from the

Installer dialog box, as shown at the

right. To install the guide, select Online

Guide and then click . Then, click

Install Reference Guide and follow

the on-screen instructions. When the

installation is complete, an ESC880

Guide icon appears in the EPSON folder. Double-click the icon to open the

guide.

5. Follow the on-screen instructions to turn on your printer.

For Windows 98 users, the printer port configuration starts

automatically.

For printers connected via USB cable, the USB device driver installation

starts automatically at this point. A message will appear asking you to

restart your computer. Follow this instruction.

Printed in Japan.xx-xx

Nagano, Japan.

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

LProof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

6. After turning on the printer, the Setup

utility opens automatically.

Follow the on-screen instructions to

install the ink cartridges, check the

print head nozzles, and clean theprint

head. When a message appears

informing you that the setup is

complete, click OK.

Note:

If the Setup utility does not start, proceed to section to install the ink

cartridge using the printer’s control panel.

7. When a message appears informing you that the installation is

complete, click OK.

Note:

If an error message appears, either the printer driver or the EPSON USB

printer device driver is not installed correctly. See "Troubleshooting" in the

Daily Use guide for details.

After the setup is complete, proceed to section to print your first page.

Ensuring that the USB driver is installed correctly

After installing the software, USB users should follow the directions below

to confirm that the USB driver is installed correctly.

Note:

The illustrations used in this section show the procedure for Windows 98.

1. Click the Start button, point to Settings, and then click Printers. Make

sure that the icon for your printer is displayed in the Printers window.

2. Select the icon for your printer, then

click Properties on the File menu.

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

Proof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

3. For Windows 98 uses, click the

Details tab and make sure that

EPUSBx: (EPSON Stylus COLOR 880)

is displayed in the Print to the

following port list box. For

Windows 2000 user’s click the Ports

tab and make sure that USBxxx,

EPSON Stylus COLOR 880 is

displayed in the Print to the following

port(s) list box.

Note:

If the correct port is not displayed, refer to

the "Troubleshooting" section of the

Daily Use guide or the Online Guide.

For Windows 3.1 users

Follow the steps below to install the software in Windows 3.1.

1. Make sure that Windows 3.1 is running and the Program Manager

window is open.

2. Insert the printer software CD that is shipped with your printer in the

CD-ROM drive. (If you use the floppy disk version, insert the disk in

the disk drive.)

3. Click Run on the File menu. The Run dialog box appears. In the

Command Line text box, type D:SETUP and click OK. The installation

program copies the printer software files.

Note:

If the CD-ROM drive is assigned a

drive letter other than “D” or if you

are using the floppy disk version of

the software, substitute the

appropriate letter.

4. When the installation is complete, click OK to exit the installation

program.

The installation program automatically selects this printer as the default

printer for Windows applications.

For information on accessing and using the software, see “Using the Printer

Software for Windows” in the Daily Use guide.

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

LProof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

For Macintosh users

Macintosh users must first install the printer software, and then select the

printer in the Chooser.

?Caution:

Turn off all virus protection programs before installing the printer software.

Installing the software

Follow the steps below to install the printer software.

1. Turn on your Macintosh and insert the software CD in the CD-ROM

drive. The contents of the EPSON printer software CD are displayed.

2. If a single Installer icon is displayed, double-click the icon. If separate

folders containing installer icons for several languages are displayed,

double-click the folder for your preferred language, then double-click

the Installer icon inside it.

Note:

It is possible to install the Reference Guide on your hard drive from the printer

software CD-ROM. To install the guide, click Install Reference Guide and

follow the on-screen instructions. When the installation is complete, a View

Reference Guide icon appears in the EPSON folder. Double-click the icon

to open the guide.

3. In the initial dialog box, click

Continue. The Installer dialog box

opens.

4. Make sure that the Install Location

box displays the correct drive to

install to, then click Install.

5. When a message appears informing

you that the installation is

complete, click Restart to restart

your computer.

Selecting your printer in the Chooser

After you have installed the printer software on your Macintosh, you must

open the Chooser and select your printer. You need to select a printer the

first time you use it or whenever you want to switch to another printer. Your

Macintosh will always print using the last printer selected.

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

Proof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

1. Choose Chooser from the Apple

menu. Then click your printer's icon

and the port that your printer is

connected to.

2. Select the appropriate

Background Printing radio button

to turn background printing on or

off.

When background printing is on,

you can use your Macintosh while it is preparing a document for

printing. In order to use the EPSON Monitor3 utility to manage print

jobs, background printing must be turned on.

3. Close the Chooser.

Installing the Ink Cartridges

Windows 98, 95, 2000, and NT 4.0 users can use the Setup utility to install

ink cartridges. Windows 3.1 and Macintosh users must use the printer’s

control panel. Refer to the appropriate section below.

Using the Setup utility

If you have Windows 95, 98, 2000, or NT 4.0 installed on your computer,

the Setup utility will open automatically when the printer software

installation is complete. Follow the on-screen instructions.

Using the printer's control panel

If you can not access the Setup utility, use the printer’s control panel to

install the ink cartridges.

MWarning:

The ink cartridges are self-contained units. Under ordinary use, ink will

not leak from a cartridge. If ink does get on your hands, wash them

thoroughly with soap and water. If ink gets into your eyes, flush them

immediately with water.

Note:

Do not open the ink cartridge packages until just before you install them; otherwise,

the ink may dry up.

R4C626Setup Guide

Rev_C

A5 size setup NO ARROWS.fm

9/8/00 Pass 0

LProof Sign-off:

Otsuka, CRE Moriyama_______

N.Nomoto _______

_______

Install the ink cartridges as described below.

1. Lower the output tray and then

open the printer cover.

2. Press the 2power

button to turn on the

printer.

The print head

moves left to the ink

cartridge installation

position. The 2

power light flashes

and the *and )ink

out lights come on.

?Caution:

Do not move the print head by hand; doing so may damage the printer.

3. Lift up the ink cartridge clamps.

Note:

Do not remove the small sponges

that are attached to the ink

cartridge clamps.

4. Open the ink cartridge packages and remove only the yellow tape seals

from each cartridge.

Otros manuales para Stylus Color 880

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora de Epson

Epson

Epson PictureMate Pal PM 200 Guía de instalación

Epson

Epson TM-T88V Manual de usuario

Epson

Epson WF-3825 Manual de usuario

Epson

Epson C1100 - AcuLaser Color Laser Printer Manual de usuario

Epson

Epson SureColor F2100 Series Manual de usuario

Epson

Epson 7880 - Stylus Pro Color Inkjet Printer Manual de usuario

Epson

Epson FX-880+ Manual de usuario

Epson

Epson Compuprint MDP30FB Manual de usuario

Epson

Epson ActionPrinter 3260 s Manual de usuario

Epson

Epson DLQ-3000 Minerva+ Manual de usuario

Epson

Epson EcoTank L8160 Series Manual de usuario

Epson

Epson DFX-8500 - Impact Printer Manual de usuario

Epson

Epson TM-U590 Series Manual de usuario

Epson

Epson 3880 - Stylus Pro Color Inkjet Printer Manual de usuario

Epson

Epson TM-T88IV ReStick Manual de uso y cuidado

Epson

Epson LQ-630 Manual de instrucciones

Epson

Epson L351 Manual de usuario

Epson

Epson 1400 - Stylus Photo Color Inkjet Printer Manual de operación y mantenimiento

Epson

Epson ET-M16600 Series Manual de instrucciones

Epson

Epson EC-01 Manual de usuario

Epson

Epson R200 - Stylus Photo Color Inkjet Printer Manual de usuario

Epson

Epson Aculaser C9200N Manual de usuario

Epson

Epson Stylus Pro 4400 Manual de usuario

Epson

Epson Mobilink TM-P60 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario

IRA3D

IRA3D POETRY4 Manual de usuario

Ricoh

Ricoh Aficio AP400 Manual de usuario

BIXOLON

BIXOLON SRP-352plusV Manual de usuario