Epson EMP 810 Manual de usuario
Network Installation Guide
Artisan
®
810 Series
2
Before You Begin
Before You Begin
Make sure you installed ink cartridges and loaded paper as described on the
Start Here sheet. Then follow the instructions in this guide to set up the printer for
use on a network.
Tip:
For a video tutorial and other information about setting up a wireless network, go to:
epson.com/support/wireless.
Do one of the following:
■If you’re installing the printer for the first time, see “Choose Your Connection
Type” on page 3.
■If you’re setting up an additional computer to use the printer on the network,
follow the steps in “Install Software” on page 22.
Choose Your Connection Type
3
Choose Your Connection Type
Wireless To connect the printer wirelessly, see page 4.
Note:
If you want to print wirelessly but do not have an access point or router, see “Create an
Ad-Hoc Wireless Connection” on page 15.
Wired To connect the printer using an Ethernet cable, see page 21.
4
Wireless Network Installation
Wireless Network Installation
To add the printer to your wireless network, you need to know the name (SSID)
of your wireless network. If it has security enabled, you also need to know the
WEP key or WPA passphrase. Write down your network and security information
in the space provided below:
■Network name (SSID): _________________________________________
■WEP key or WPA passphrase: ____________________________________
Note:
Your printer is compatible with 802.11b and 802.11g. If your router or access point
supports 802.11n (Wireless N), makes sure it is set to compatibility mode to allow
802.11b and 802.11g devices to connect to it.
Your printer supports the following wireless security modes: WEP, WPA, and WPA2.
If you don’t know your wireless network name (SSID), WEP key, or WPA passphrase,
contact the person who set up your wireless network before you begin.
If your WPA passphrase contains upper- or lowercase letters, be sure to note it
correctly.
Connect Wirelessly Using the Setup Wizard
Follow the steps below to connect to your wireless network.
1. Press the Home button, if necessary, and select Setup on the printer’s control
panel.
Wireless Network Installation
5
2. Press lor rand select
Network Settings
.
3. Select
Wireless LAN Setup
, then select
Wireless Setup Wizard
.
4. Select the name of your wireless network. (If more than 3 networks are
detected, press lor rto view the rest of the list.)
If your network name isn’t listed, try the following:
■Make sure that your wireless router or access point is turned on and
working correctly. Press the y
Back
button to return to the previous
screen, select
Wireless Setup Wizard
, then repeat step 4.
■If you still can’t find the network name in the list, your router or access
point is not broadcasting its network name. Press the y
Back
button, then
see “Connect Wirelessly Using Advanced Setup” on page 8.
6
Wireless Network Installation
5. Do one of the following:
■If your wireless network doesn’t have security enabled, continue
with step 8.
■If your wireless network has security enabled, continue with step 6.
6. Use the arrow buttons on the printer’s control panel to enter your WEP key or
WPA passphrase.
Important:
WPA passphrases and WEP keys in ASCII format are case-sensitive. Be sure to
enter upper- or lowercase letters as necessary.
■Press x
Menu
to switch between uppercase (
ABC
), lowercase (
abc
), or
numeric/special (
123
) characters.
■Press uor duntil you see the character you want.
■Press lor rto move the cursor.
■Press
–
to delete a character.
7. When you’re done entering your WEP key or WPA passphrase, press
OK
.
Press the xMenu button to switch between
uppercase, lowercase, or numeric/special characters.
To enter a character:
Press uor dto select a character.
Press lor rto move the cursor.
Press –to delete a character.
Indicates current selection: ABC, abc, or 123.
Wireless Network Installation
7
8. When you see a screen like this one, verify that the settings are correct. If you
need to change a setting, press y
Back
until you see the setting you need to
change.
9. Once you have verified that your network settings are correct, press
OK
to save
the settings and return to the Network Settings menu.
10. Press the
Home
button to exit the Network Settings menu.
11. Wait for the printer to connect to your wireless network (this can take up to
90 seconds).
Once it’s connected, you see the WiFi icon and a signal strength indicator
on the printer’s control panel.
12. Continue with “Install Software” on page 22.
Note:
If the printer doesn’t connect to your wireless network after 90 seconds, the WEP key
or WPA passphrase may have been entered incorrectly. See “Connect Wirelessly Using
the Setup Wizard” on page 4 to select your network settings again.
If the printer still doesn’t connect to your wireless network, see “The printer cannot
find or connect to the wireless router or access point” on page 29.
Wireless connection
established
8
Wireless Network Installation
Connect Wirelessly Using Advanced Setup
Use this setup method if your access point or router isn’t broadcasting its network
name (SSID). Make sure you know the type of security your access point or router
uses (WEP, WPA, or WPA2), and the key or passphrase.
1. Press the
Home
button, if necessary, and select
Setup
on the printer’s control
panel.
2. Press lor rand select
Network Settings
.
3. Select
Wireless LAN Setup
, select
Advanced Setup
, then select
Manual
Wireless LAN Setup
.
Wireless Network Installation
9
4. When you see this screen, press
OK
.
5. Select
Infrastructure Mode
.
6. Select
Enter SSID
.
10
Wireless Network Installation
7. Use the arrow buttons on the printer’s control panel to enter your wireless
network name (SSID).
Important:
Network names are case-sensitive. Be sure to enter upper- or lowercase letters as
necessary.
■Press x
Menu
to switch between uppercase (
ABC
), lowercase (
abc
), or
numeric/special (
123
) characters.
■Press uor duntil you see the character you want.
■Press lor rto move the cursor.
■Press
–
to delete a character.
8. When you’re done entering your wireless network name, press
OK
.
To enter a character:
Press uor dto select a character.
Press lor rto move the cursor.
Press –to delete a character.
Press the xMenu button to switch between
uppercase, lowercase, or numeric/special characters.
Indicates current selection: ABC, abc, or 123.
Otros manuales para EMP 810
2
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Impresora todo en uno de Epson
Epson
Epson NX515 - Stylus Color Inkjet Manual de usuario
Epson
Epson L405 Series Manual de usuario
Epson
Epson XP-411 Manual de instrucciones
Epson
Epson Stylus Photo PX720WD Manual de usuario
Epson
Epson Stylus CX8400 Series Manual de usuario
Epson
Epson Stylus NX625 Series Manual de usuario
Epson
Epson Stylus SX200 series Instrucciones de montaje
Epson
Epson L3110 Series Manual de instrucciones
Epson
Epson Stylus NX230 Manual de usuario
Epson
Epson Expression Photo XP-960 Manual de instrucciones
Epson
Epson ET-4750 series Manual de usuario
Epson
Epson Expression EcoTank ET-3600 Manual de instrucciones
Epson
Epson Stylus Photo PX830FWD Instrucciones de montaje
Epson
Epson Stylus Scan 2500 Manual de usuario
Epson
Epson Stylus CX5900 Series Manual de instrucciones
Epson
Epson L485 SERIES Manual de usuario
Epson
Epson Stylus Scan 2500 Manual de instrucciones
Epson
Epson WorkForce Pro ST-C5000 Manual de usuario
Epson
Epson 3880 - Stylus Pro Color Inkjet Printer Instrucciones de instalación y mantenimiento
Epson
Epson Stylus CX4900 Series Guía
