Envision G2219W1 Manual de usuario
G2219w1
Operation Instructions
Thank you for purchasing this monitor, a high-resolution multi-scan color
monitor.
Please read this guide thoroughly before installation.
FCC RADIO FREQUENCY INTERFERENCE STATEMENT WARNING:
(FOR FCC CERTIFIED MODELS)
This monitor has been tested and found compliant with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide proper protection against harmful interference to a
residential installation. This monitor generates, uses, and can radiate radio
frequency energy. Harmful interference to radio communication may be
led as a result if it‘s not properly installed and used. However, there is no
guarantee that interference will not occur in a particular installation. If this
monitor does cause serious interference to radio or television reception,
resetting the monitor may determine it. Moreover, users are encouraged to
correct interference by doing one or more of the following:
Reorient or relocate the receiving antenna.
Move the monitor and the receiver further away from each other.
Connect the monitor into an outlet on a circuit different from that to
which the receiver is connected.
Consult your local dealer or an qualied technician.
FCC Warning:
To assure a continued FCC compliance, a user must use a grounded power
supply cord and the provided shielded video interface cable with bonded
ferrite cores. Also, any unauthorized changes or modications to this monitor
would void the user‘s authority to operate this device.
LAMP(s) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST
BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE
OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE
ELECTRONICS INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
Note: If necessary, shielded interface cables and AC power cord must be
used to meet the emission level limits.
English
Content
Safety Precautions.............................................................................1
First Setup .........................................................................................2
Quick Installation.............................................................................2-5
Using On Screen Display (OSD) Functions ....................................7-9
Supporting Timing Modes .................................................................10
Technical Information........................................................................11
Care and Maintenance.....................................................................12
Troubleshooting ...............................................................................12
Rear View of the Product .................................................................. 6
Front View of the Product .................................................................. 6
English
Safety Precautions
This monitor is manufactured and tested on a ground principle that a user’s
safety comes first. However, improper use or installation may result danger
to the monitor as well as to the user. Carefully go over the following
WARNINGS before installation and keep this guide handy.
WARNINGS:
This monitor should be operated only at the correct power sources
indicated on the label on the rear end of the monitor. If you’re unsure of
the power supply in your residence, consult your local dealer or power
company.
Do not try to repair the monitor yourself as it contains no
user-serviceable parts. The monitor should only be repaired by a
qualified technician.
Do not remove the monitor cabinet. There is high-voltage parts inside
that may cause electric shock to human bodies, even when the power
cord is disconnected .
Stop using the monitor if the cabinet is damaged. Have it checked by a
service technician.
Put your monitor only in a clean, dry environment. Unplug the monitor
immediately if gets wet and consult your service technician.
Always unplug the monitor before cleaning it. Clean the cabinet with a
clean, dry cloth. Apply non-ammonia based cleaner onto the cloth, not
directly onto the glass screen.
Keep the monitor away from magnetic objects, motors, TV sets, and
transformer.
Do not place heavy objects on the cable or power cord.
1
For PLUG CABLE EQUIPMENT, the Socket-outlet shall be installed
near the equipment and shall be easily accessible.
English
First Setup
Congratulation for purchasing this monitor of high performance!
This monitor comes with the following accessories:
Power Cable
D-Sub Cable (15 pin)
Warranty Documents
User’s Guide
Quick Start Guide
Quick Installation
Installing & Removing the Base
Install Remove
2
h
s
i
lgnE
3
Preparing To Install The Optional Wall Mount Arm (Not
Included)
English
This monitor can be attached to a wall mounting arm you can purchase separately.
Turn the power OFF then dis-connect the cables from the monitor before performing
the procedure below. Lay the monitor face down on a soft surface.
1. Remove the plastic hinge cover. It is attached to the back of the monitor
by hooks.
2. Remove the 4 screws holding the stand to the back of the monitor.
3.Remove the stand.
4
English
Attaching The Optional Wall Mount Arm (not supplied)
Follow these steps to finish installing the wall mounting arm:
1. Place the wall mounting arm onto the back of the monitor. Line up the
holes of the arm with the holes in the back of the monitor.
2. Insert the 4 screws into the holes and tighten.
3. Reconnect the cables. Refer to the user’s manual that came with the
optional wall mounting arm for instrucstions on attaching it to the wall.
NOTE
The ENVISION G2219w1 is in compliance with the most current revision of the VESA
100mm Flat Panel Monitor Physical Mounting Interface (FPMPMI standard).
Connecting the Monitor
1. Connect Power Cable
Connect the power cable to the back of the monitor. Plug the power cable to a
nearby power outlet.
2. Connect Analog video cable (D-Sub cable)
Make sure both monitor and computer are powered OFF. Connect the video
cable ( D-Sub cable) to the computer, then to the monitor.
3. Connect DVI cable (Optional)
Connect the DVI cable from DVI output of computer to the DVI input of the
monitor.
4. Power-ON computer and monitor
Power-ON the computer, then Power-ON the monitor.
5. Windows users: Setting the Timing Mode (Resolution and Refresh Rate)
Example: 1680 x 1050 @ 60 Hz (Recommended Resolution)
Resolution Right-click on the Windows desktop > Properties > Settings >
“Desktop Area”. Set the resolution.
Refresh Rate (vertical frequency) See your graphic card’s user guide for
instructions.
Connection Diagram:
5
English
Front View of the Product
➊ OSD TURN ON/OFF ➍ CONFIRM SELECTION
➋ SCROLL DOWN/DECREASE ➎ POWER ON/OFF
➌ SCROLL UP/INCREASE ➏ LED INDICATOR
Rear View of the Product
➐ POWER INPUT ➒VGA INPUT (D-SUB 15 PIN)
➑ DVI INPUT (DVI 24 PIN)
6
English
Using On Screen Display (OSD) Functions
Main Menu
7
English
1
Exit from OSD menu.
Auto adjust the image when at root menu.2
Confirm the selection.
Select the desired item when in OSD menu.
When not in OSD menu, it is to immediately activate Contrast/
Brightness. It should be change to Contrast/ Brightness by pressing
button W.
Vor W
When not in OSD menu, it is to immediately activate Screen 16:10/
4:3. It should be change to image ratio by pressing button V.
▼+ ▲Recall both of Contrast and Brightness.
1 + ▼Power Lock (when not in OSD menu)
1 + ▲OSD Lock (when not in OSD menu)
Display main menu.
Otros manuales para G2219W1
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Monitor de Envision
Envision
Envision E218C1 Manual de usuario
Envision
Envision G2461w Manual de usuario
Envision
Envision H2460w Manual de usuario
Envision
Envision EN9250 Manual de usuario
Envision
Envision H22W Manual de usuario
Envision
Envision G2219W1 Manual de usuario
Envision
Envision H919w+ Manual de usuario
Envision
Envision G2770 Manual de usuario
Envision
Envision LCD Manual de usuario
Envision
Envision Envision H1781 Manual de usuario
Envision
Envision EN9250 Manual de usuario
Envision
Envision EN-985e Manual de usuario
Envision
Envision EN-7220 Manual de usuario
Envision
Envision EN9410e Manual de usuario
Envision
Envision H2062 Manual de usuario
Envision
Envision EFT920 Manual de usuario
Envision
Envision G2470 Manual de usuario
Envision
Envision P951wa Manual de usuario
Envision
Envision EN9110 Manual de usuario
Envision
Envision E218C1 Manual de usuario
