Envirovent energiSava 200 Manual de usuario
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT THROW AWAY
energiSava® 200
CEILING MOUNTED VERSION
INSTALLATION GUIDE
2energiSava®200
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Safety
Read and understand these instructions carefully before
beginning installation. The unit should only be installed by a
competent person.
Electrical Connection
The unit requires a continuous electrical power supply. Connection to
the fixed wiring must be made outside the unit in a suitable location.
The unit must be able to be disconnected from the mains supply
after installation. The unit must be earthed and a double pole switch
having a minimum contact separation of 3.0mm must be used to
provide isolation for the unit.
The power cable running into the unit must remain the supplied
flexible cable (not a solid core lighting cable]. If the power cable
becomes damaged, it must be replaced by EnviroVent, an authorised
service agent for your region/country, or a similarly qualified person in
order to avoid a hazard. Do not remove or tamper with any electronic
components inside the unit.
All wiring must comply with Building Regulations and the current
IET Wiring Regulations (BS7671 in the UK) or equivalent standards for
other countries. The final installation should be examined and tested
by a qualified electrician.
The unit is considered to be suitable for use in countries having a
warm, damp equable climate. It may also be used in other countries.
Electrical power is to be supplied to the unit through a residual
current device (RCD) with a rated residual operating current not
exceeding 30mA.
3
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
Location
Check there is space for the unit in your chosen location including
room for access and future servicing of the unit. The unit must not
affect the operation of open-flue appliances. Consider the external
vent locations in relation to open-flues from appliances e.g. boilers.
You must ensure the external supply grilles are positioned away from
open flues to avoid drawing harmful gases into the property. Consult
your local regulations or a qualified gas engineer.
Users
This unit is not intended for use by persons [including children] with
reduced physical, sensory or mental capabilities or lack of experience
and knowledge, unless they have been given supervision and usage
instruction by a person responsible for their safety. Children should
be supervised to ensure they do not play with the unit. Cleaning and
user maintenance must not be performed by children.
4energiSava®200
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Diagrams
The energiSava®200 spigots are compatible with ø125mm duct.
Overall unit dimensions and minimum area required for
access & maintenance (mm).
645
560
1144
200 300
335
644
335
5
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
WIRING
The local isolator must be connected to the mains as
part of the fixed wiring. Connect the cores of the power
cable to the matching terminals on the local isolator
(3A fuse spur or similar).
The black switch live core of the mains cable can be
wired to a switch input such as a light switch. When
the switch is turned on, the boost function is engaged.
When the switch is turned off, the unit will return to
normal running mode. In this configuration a triple pole
isolator must be used.
Diagrams
MVHR UNIT
LOCAL ISOLATOR
LN
L
NMAINS SUPPLY
230V 50/60Hz
POWER CABLE
SWITCH LIVE
(OPTIONAL)
Ls
Ls
6energiSava®200
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
About the energiSava®200
The energiSava®200 is an MVHR unit (Mechanical Ventilation with Heat
Recovery). It is ideal for small to medium sized properties with a kitchen
and up to 5 additional wet rooms. The unit is capable of delivering a
maximum airflow of 241m3/h (67l/s) and a maximum system pressure
in excess of 500Pa.
The unit will help to create a fresh and healthy living environment by
supplying filtered air into a property through supply valves. Moist, stale
air is removed out of the property through extract valves.
The heat exchanger inside the unit transfers waste heat energy from
the extracted air to the supplied air in order to improve the thermal
efficiency of the property and reduce heating costs.
The frost protection feature automatically uses the warm extracted
air to ensure the heat exchanger inside the unit does not freeze when
outdoor temperatures are below 5ºC.
The Intellitrac®humidity tracking function monitors the humidity levels
in the extracted air and will automatically increase the supply and
extract air flow rates when the humidity levels rise. Once the humidity
levels are lower the air flow rates will return to the normal rate.
The mechanical summer bypass feature automatically diverts
some of the supplied air around the heat exchanger at temperatures
above 25ºC to avoid the property overheating when the outdoor air
temperature is high.
The energiSava®200 includes a switch live function. When wired
through the lighting switch of a room (such as a bathroom) the unit
will enter boost mode whenever the light is turned on.
7
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
EnergiSava®200
• 1x energiSava®200 unit
• 1x Remote control
• 1x Instruction guide
• 1x User guide
• 2x Mounting brackets
• 10x Screws 8g x 2.0”
• 10x Plasterboard plugs
• 2x Wing nuts
• 1x Screw 10g x 0.5”
• 1 x Condensate drainage kit
EnergiSava®200 App
• 1x energiSava®200 app unit
• 1x Instruction guide
• 1x User guide
• 1x App guide
• 2x Mounting brackets
• 10x Screws 8g x 2.0”
• 10x Plasterboard plugs
• 2x Wing nuts
• 1x Screw 10g x 0.5”
• 1 x Condensate drainage kit
Box Contents
Pre - Installation Checklist
• Does the unit fit in the space where it will be installed?
• Is there room to connect ducts to the spigots without tight duct bends?
• Is there room to access and replace the filters after installation?
• Are there any obstructions above or below the locations where the
input and extract valves are to be fitted?
• Is the mounted surface strong enough to support the unit?
• Is the mounting surface level?
• Are there adequate facilities to connect the unit condensate drain to
the internal waste system of the property?
8energiSava®200
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Installation
1. Hold the unit up to the chosen location and check there is space
for ducts, condensate drainage, filter and keypad access.
2. Once you are satisfied with the position, line up the two brackets
using the printed template then secure them to the mounting surface.
Use 5 8gx2.0” screws and 10 plasterboard plugs.
3. Mount the unit onto the brackets ensuring that it is fully supported.
4. Apply the two wing nuts onto the threaded studs then insert the
self-tapping screw into the hole and tighten it. This will ensure the
unit cannot be accidentally knocked off the brackets.
2
4
1
3
9
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
5. Fit the external supply and extract terminations.
6. Fit the supply and extract valves inside the property.
7. Fit the ductwork between the external terminations, the MVHR unit
and the supply and extract valves.
5 6
7Ductwork should be fitted in
accordance with the Domestic
Ventilation Compliance Guide.
(Example RH unit configuration
shown).
Ducts to and from atmosphere
and through unheated spaces
need to be insulated.
For efficiency, all ductwork should
be as large a diameter as possible
(min. 125mm) and use rigid or
semi rigid duct.
Supply Extract
Extract 1
Supply 1
Extract 2
Supply 2
10 energiSava®200
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Extract to
atmosphere
S
uppl
y
f
ro
m
a
tmosp
h
er
e
Supply to
property
Extract from
property
Extract to
atmosphere
S
upply
f
ro
m
a
tmosp
h
er
e
Supply to
property
Extract from
property
8. Connect each duct path to the spigot.
8a. LH Units
9. Make a water-tight connection between the two drainage connectors
on the unit and the waste water system in the property. A suitable non-
return device must be fitted to ensure air and waste water from the
drain system do not flow back up into the unit. The drainage must be
fitted with a minimum 5 degree fall away from the unit.
8b. RH Units
9a. LH Units 9b. RH Units
Otros manuales para energiSava 200
4
Tabla de contenidos
Otros manuales de Admirador de Envirovent
Envirovent
Envirovent kudos Manual
Envirovent
Envirovent Eco dMEV+ Manual de usuario
Envirovent
Envirovent ECO DMEV+ LC Manual de usuario
Envirovent
Envirovent MEV SPIDER Manual de usuario
Envirovent
Envirovent energiSava 250 Manual de usuario
Envirovent
Envirovent SILENT MV-160/100 Instrucciones de montaje
Envirovent
Envirovent MEV SPIDER Manual de usuario
Envirovent
Envirovent ECO dMEV LC Manual
Envirovent
Envirovent OZEO Manual de usuario
Envirovent
Envirovent Slimline 150 Guía de inicio rápido
Envirovent
Envirovent POWER-170 Instrucciones de montaje
Envirovent
Envirovent filterless extractor fan Manual de usuario
Envirovent
Envirovent energisava 380 Manual de usuario
Envirovent
Envirovent SILENT 100 Manual
Envirovent
Envirovent ECO DMEV Manual de usuario
Envirovent
Envirovent SELV Guía de inicio rápido
Envirovent
Envirovent Damp Pro DP-EVL Manual de usuario
Envirovent
Envirovent PIV AIR SOURCE Manual de usuario
Envirovent
Envirovent fliterless infinity fan 230v Guía de inicio rápido
Envirovent
Envirovent PIV Manual de usuario
