ENVIRORIDES R1+ Manual de usuario
User-Manual Content
1) Introduction
2) Product Overview
3) Parameter & Malfunction
4) Preparation To Ride
5) Battery & Charger
6) Accessories
7) Socials and Content
8) Warranty Details
9) Legal Information
Introduction
1.1) We hope you enjoy your new purchase, for your safety and
legal responsibility, read this user manual fully before using the
EnviroRides R1+ Electric Scooter. Failure to do so may risk the
chances of accident, prosecution, injury, or even death.
If you have any questions regarding this product, please contact
us either via our email, on-site messenger, phone, or our social
media outlets.
1.2) Be aware, your actions could lead to personal injury, public
injury, or fatality. EnviroRides holds no liability in any event when
using this product.
Product Overview
2.1) R1+ 3600W Electric Scooter by EnviroRides.
2.2) Please familiarise yourself with the controls graphic below.
2.3) To power up the R1+ Electric Scooter, firstly turn the
eScooter on from the on / off button on the base. Then ensure
the ignition key is fully turned to the right (clockwise) or the key
fob ignition button has been pressed twice. Once the ignition is
switched on or the key fob ignition button has been pressed
twice proceed to hold the power button to turn on the R1+
Electric Scooter.
2.4) To change the readings on your R1+ Electric Scooter
screen, press the mode button to scroll through.
▪Time
▪Trip
▪Odometer
▪Distance
▪Voltage
▪Channel
Pressing and holding the mode button will clear the “Trip” log.
2.5) To change the speed settings, press the power button
once. This will cause the speed setting symbol to flash. Once the
speed setting symbol is flashing press the mode button to
change the speed setting. Do not forget to press the power
button again to lock the speed setting.
2.6) Remote Fob Symbols
Power On (Press twice to power up)
Unlock (Press twice to turn off)
Lock (Press twice to lock)
Mute (Press twice to mute)
Parameter & Malfunction
3.1) Press and hold both the power and mode buttons to access
the eScooters parameter settings. (DNA: Do Not Adjust*)
▪P0: 10 (Wheel Diameter) DNA*
▪P1: 42 (Battery Voltage) DNA*
▪P2: 17 (Motor Setting) DNA*
▪P3: 1 (Motor Setting) DNA*
▪P4: 1 or 0 (MPH or KM/PH)
▪P5: 1 or 0 (Kick Start)
▪P6: 1 or 0 (Cruise Control)
▪P7: 1 or 0 (Soft or Hard Start)
▪P8: 100 (Motor Setting) DNA*
▪P9: 1 or 2 (Electric Assist Braking Strength)
3.2) eScooter malfunction symbols.
Brakes Activated
▪This symbol will highlight when the R1+ Electric Scooter
Brakes are in use. If this symbol remains on when brakes
are not in use, please see possible faults below.
oDamaged Brake Levers
oDamaged Brake Callipers
oDamage Electrical Brake Cables
oDamaged Electrical Brake Cable Fittings
Motor Fault
▪This symbol will highlight when the R1+ Electric Scooter
Motor has incurred a fault. If this symbol is activated,
please see possible faults below.
oDamaged Motor Cables
oDamaged Motor Internals
Throttle or Motor Fault
•This symbol will highlight when the R1+ Electric Scooter
Motor or Throttle Unit has incurred a fault. If this symbol is
activated, please see possible fault below.
oDamaged Throttle Unit
oDamaged Throttle Cable Fitting
oDamaged Motor Cables
oDamaged Motor Internals
Controller Unit Fault
•This symbol will highlight when the R1+ Electric Scooter
Controller Unit(s) or Throttle Unit has incurred a fault. If
this symbol is activated, please see possible fault below.
oDamaged Controller Unit
oDamaged Throttle Unit
oDamaged Throttle Cable Fitting
3.3) What to do if you have a malfunction?
If you encounter any of the errors listed above, photograph the
error symbol, or notify us in the feedback section on the
EnviroRides Warranty Process Form or the EnviroRides
Servicing & Repairs Process Form.
Please refer to our Warranty Details to establish if your issue is
covered under warranty.
The Technical Team may require your eScooter to be returned to
the EnviroRides Depot for further assessment. Ensure you keep
the original packaging, or you may be required to purchase an
appropriate replacement carton and packaging.
Items returned without original or in unsuitable packaging
will not be refunded and or may incur further costs.
Preparation To Ride
4.1) Please familiarise yourself with the R1+ Electric Scooter
graphic below.
Please note that all the specification for this eScooter are based on tests at optimal conditions and
rider weight of 65kg. Speeds and distances may vary depending on rider's weight, battery level,
terrain, weather, and temperature. Additional weight can see a reduction of up to 5-15% on listed
specifications.
4.2) Unfold your R1+ Electric Scooter by lifting the stem forward.
See below.
Once unfolded, slide the stem clamp down oven the folding
mechanism, ensure the stem clamp is sitting flush to the bottom
See below.
Once positioned, close the lever to ensure the stem clamp is
fitted tightly. See below
4.3) DO NOT USE THE ELECTRIC SCOOTER WITHOUT
CHECKING ALL FIXTURES AND FITTINGS.
4.4) Ensure you have a clear area before using the R1+ Electric
Scooter. Check your surroundings when riding your eScooter to
avoid accidents, collisions, or damage to the rider, others, or the
eScooter.
4.5) Power up your R1+ Electric Scooter.
The R1+ Electric Scooter is set to speed one and to soft start
from dispatch to ensure your safety. Slowly press the accelerator
whilst keeping one foot aside in case you need to stop. Slowly
increase the acceleration as you become more capable and
proficient.
4.6) Braking. Ensure you are familiar with your brakes before
riding. As this is a new item the brakes may be tight for the first
few trips, bed them in at slow speeds and do not brake sharply or
erratically as this will cause warping of the brake discs and
reduce braking capabilities. Never use the accelerator and
brakes at the same time.
4.7) Maintain correct tyre pressure. Over or under inflated tyre
pressure may increase risk of failure, collision, or damage. Do not
ride with low or flat tyres, this will damage the alloy and tyres.
4.8) Always wear protective clothing when riding.
4.9) Use extra caution in wet or icy conditions, reduce speed to
minimum and use dual braking (the use of both brakes in
conjunction) to reduce chance of skidding.
4.10) Do not expose your eScooter to excess water or moisture.
Do not ride in heavy rain, sleet, snow or through rivers and
streams.
Tabla de contenidos
Otros manuales de Scooter de ENVIRORIDES
