-
Atier having tested pressure on the whole installalion, every single connected appliance- including burrrer
function - has to be tested while f'unctioning. A visual control ofthe l)ame height on the burners has to be carried out
while all burners are being operated in order make sure the service pressure is suitable fbr each appliance.
BEFORE LEAVING
lgnite all burners both individually and in combination to ensure correct operation ofgas valves, bunrers, flame l'ailure
device and rgnition. Turn gas taps to low 1lame position and observe stability o1'llame lbr each burner both individually
and in combination. When satislled with the operation rnstruct the user with correct method operation. ln case the
appliance fails to operate correctly after all checks have been carried out, refer to the authorised service provider in your
afea
VENTILATION
- must be in accordance with A5560 I - Cas installations section 6.3.7 ln general, pcrmanent openings to olrtslde areas are
required so that the applrance has adequate ventjlation tbr complete combustion ol gas, proper t)ueing and ro nrarnl.ain
temperature of rmmediate surroundings withirr saf'e limits. Operating a gas cookirrg appliance brings abor-rt heat and damp
exhaust in the room where it is being operated. Always make sure that the room is properly ventilated: keep natural
aeration apertures opened or install a mechanical aeration device (hood)
An intensive and prolonged operatron can require an extra ar'ration (by opening a window) or by providing a rnore
eiJicient aeration (hood - ifany - on t'ull on position).
COMB U STI BL E SU RI,-ACES
Any adjoining wall surface situated within 200mm liom the edge ofany hob burner must be a siLitable non combustibie
matenal fbraheightof l50mmfbrtheentrrelengthoithehob Anycombustibleconstructionabovethehotplatemustbe
600mm above the top olthe burner and no construction shall be within 450mm above the top ofthe burner
Pressure -fest Pornt: Ensure that the gas supply pressure at the test pornt is 2.75 kPa.
- A complete check-up should be carried out punctuaily betbre leavrng.
IV - HOW TO REPLACE the BATTERY (electronic isnition device)
- Unscrew battery support cap - at the back olthe appliance
in an anti-clockwise direction, replace with a 1.5 V battery (AA).
- Re-assemble by proceeding in the reverse order.
- lfyou do not use your appliance for a long period, remove battery
IJ.
[(( t ---l
l*r
V - BURNERS IGNITION
Each burner is berng controlled by a valve with control knob. The indicator on the knob indicates valve
position. A syn,bol on the tascia panel indicates the burner posltron.
Each burner is being guided by a tap rvith control knob. The indicator on the knob indicates tap positron. A
symbol on the tascia panel indicates burner position
'lo light a bumer, depress and tum the respectlve control knob to the leli until the knob coincides rvith the large
11ame symbol on the lascia panei (this denotes firll on posrtion). Apply a lighted match or other lighting device to the
bumer (or press eiectronic lgnltion button).
Keep the control knob depressed lor l0 seconds until the tlame lailr,rre devrce is lltted, then release
liburner is not alight, repeat the operation. Wished setting can be obtained by gradually tLlrnrng the control
knob until the indicator coincides with the small flame symbol on the tascia panel
To extinguish the burner, tum the control knob to the right to the Ol'F'position lvhere the knob rr'ill lock in the
OFF position (full symbol)
SYMBOLS: I - Large burner knob 2 - Medium burner knob
qO 10@
I r' A
@
