Endura EC1 Manual de usuario
™
User Manual
Desktop Models: EC1 / EC1-V2
In-Vehicle Models: EC1M / EC1M-V2
FOR RECHARGEABLE TWO-WAY RADIO BATTERIES
Single Unit Rapid Charger
ENDURA EC1 / EC1M CHARGERS
Table of Contents
PageTopic
Introduction
Important (read before use)
Caution (read before use)
Replacing A Charging Pod
EC1 Features
Accessories For In-Vehicle Installation
In-Vehicle Installation (EC1M)
Charging A Battery
Fault Conditions & Advisements
Warranty And Service
Specifications
Accessories (EC1 / EC1M)
1
2
3
5
6
7
9
13
17
18
19
11
1
Introduction – EC Chargers
Thank you for purchasing an Endura™ EC charger. There are four EC charger models
covered in this User Manual: EC1 / EC1M and EC1-V2 / EC1M-V2. Model EC1 is for
desktop use and includes an AC to DC power supply. Model EC1M is for in-vehicle use
and includes the accessories needed for installation in a vehicle. The charger base
used with EC1 and EC1M is the same and it’s compatible with nearly all Endura TWP
charging pods. Similar to EC1 and EC1M, model EC1-V2 is for desktop use and model
EC1M-V2 is for in-vehicle use. The “V2”models are required for a few Endura TWP
charging pods that are not compatible with EC1 /EC1M. Feature differences for the V2
models are noted in this manual where appropriate.
All EC models are designed for charging two-way radio batteries whether on or off a
radio. Based on the charging pod installed, EC models can rapid charge these battery
chemistries: lithium ion (Li-Ion), lithium polymer (LiPo), nickel-metal hydride (NiMH),
or nickel cadmium (NiCd).
2
If you wish to replace the charging pod in the future, check the model number on the
product label (EC1 or EC1-V2) to ensure the replacement pod selected is compatible
with your model. For a complete list of charging pods available or to confirm pod
compatibility, contact a Power Products dealer, visit www.powerproducts.com, or call
customer service at 800-529-1618.
Important
1. Read all Caution statements below and this User Manual before attempting to
charge a battery.
2. Check to make sure a charging pod compatible with your battery is properly
installed before charging a battery or installing the charger in a vehicle.
3. Always charge new batteries completely before initial use. Recycle batteries
when they can no longer be used. Do not discard unwanted batteries in the trash
or incinerate. Batteries exposed to fire or excessive heat may explode.
4. For best battery performance, charge NiCd and NiMH batteries when they are
fully discharged.
3
Caution
1. Based on the pod selected, EC models can charge Li-Ion / LiPo and / or NiMH
/ NiCd batteries. If the pod is designed for Li-Ion / LiPo only, do not attempt to
charge NiMH / NiCd batteries. If the pod is designed for NiMH / NiCd only, do not
attempt to charge Li-Ion / LiPo batteries. Do not use EC models to charge batteries
with other chemistries or batteries that do not have overcharge protection.
2. Use charger in areas protected from the weather. Do not expose the charger to
rain, any liquids, or excessive moisture.
3. Do not attempt to charge a battery without first installing the appropriate charging
pod. Use only charging pods designed for your EC model. Disconnect charger
from the power source before installing, adjusting, or removing the charging pod.
4. Make sure contacts in charging pod and on the battery are clean. Do not allow
wire or metal objects to touch contacts in charging pod or any internal part of the
charger.
5. Do not remove the charger’s housing or make any modification to the charger.
4
Caution (continued)
6. Use only the power supply or vehicle power adapter provided with the EC model. If
a replacement is required, see section Accessories. Use of other power supplies
may damage the charger or batteries you may be attempting to charge.
5
Replacing A Charging Pod
The charging pod is made from quality materials and designed to provide years of
service when properly used. In most cases, the charging pod will only be replaced
when you want to use the charger with a different battery.
Follow these steps to change the charging pod:
1. Obtain a charging pod made specifically for EC1 or EC1-V2. Confirm that the
charging pod is compatible with the battery you want to charge.
2. Unplug the charger from its power source.
3. The charging pod is secured to the base with a single screw. To remove, turn the
locking screw on the bottom of the charging pod counter-clockwise until it no
longer holds the pod. Lift the charging pod from the charging base.
4. Insert the replacement charging pod into the charger base and secure with the
locking screw. Do not over tighten the screw.
5. Inspect the charging contacts to ensure they are clean and unobstructed.
6. Connect the power supply or vehicle power adapter to the charger. You are now
ready to charge a battery compatible with the charging pod.
6
EC1 Features
1. Charger base.
2. Removable charging pod.
3. DC power connection – back of charger.
4. Status LED information – also see
bottom label.
5. Charge status LED – illuminates
green, red, or orange.
6. AC to DC power supply (EC1 / EC1-V2 only).
1
3
2
6
5
4
7
Accessories For In-Vehicle Installation
The items below are included with EC1M and allow the charger to be used in a vehicle.
1. Main mounting bracket.
2. Adjustable tie-down strap – secures battery or radio in charger.
3. Holes for securing main bracket to optional 4-hole AMPS bracket.
4. Holes (2) for securing charger on main bracket with thumb screws (see #10).
5. Holes (4) for securing bracket to wall or floor.
6. Connection point for securing tie-down strap.
7. Side flanges (2) – attach to main bracket for floor mounting.
8. Connection points (2) for attaching charger to main bracket.
9. Vehicle power adapter – supplies power from a vehicle’s 12V or 24V outlet.
10. Thumb screws and insert nuts (2 each) for locking charger to main bracket.
11. Screw (24 mm) for fastening bracket to wall or floor (quantity 4).
12. Machine screw and locking nut for attaching flanges to main bracket (quantity 4).
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Cargador de baterías de Endura
Endura
Endura EC-4173 Manual de usuario
Endura
Endura NCC0355 Manual de usuario
Endura
Endura TWC12M Manual de usuario
Endura
Endura TWC2M Manual de usuario
Endura
Endura TWC1 Manual de usuario
Endura
Endura TWC6M Manual de usuario
Endura
Endura TWC1M Manual de usuario
Endura
Endura NCC0325 Manual de usuario
Endura
Endura EC1C-BK2 Manual de usuario
Endura
Endura TWC6M Manual de usuario
