Endress+Hauser Smartec CLD18 Manual de usuario

Products Solutions Services

Operating Instructions

Smartec CLD18

Conductivity measuring system

BA01149C/07/EN/04.16

71314731

Table of contents

Endress+Hauser 3

Table of contents

1 Document information ......... 4

1.1 Warnings ........................... 4

1.2 Symbols used ........................ 4

1.3 Symbols at the device ................. 4

2 Basic safety instructions ....... 5

2.1 Requirements for the personnel ........ 5

2.2 Designated use ...................... 5

2.3 Occupational safety .................. 5

2.4 Operational safety ................... 6

2.5 Product safety ....................... 6

3 Incoming acceptance and

product identification .......... 7

3.1 Incoming acceptance ................. 7

3.2 Product identification ................. 7

3.3 Scope of delivery ..................... 8

3.4 Certificates and approvals ............. 9

4 Product description ........... 10

5 Installation .................... 11

5.1 Installation conditions ............... 11

5.2 Mounting the compact device ......... 17

5.3 Post-installation check ............... 17

6 Electrical connection .......... 18

6.1 Electrical connection of the

transmitter ........................ 18

6.2 Ensuring the degree of protection ..... 20

6.3 Post-connection check ............... 20

7 Operation options ............. 21

7.1 Operating keys ..................... 22

7.2 Menus ............................ 23

8 Commissioning ................ 24

8.1 Switching on the device .............. 24

8.2 Display settings (Display menu) ....... 24

8.3 Device configuration (Setup menu) .... 25

8.4 Extended setup (Extended Setup

menu) ............................ 25

8.5 Calibration (Calibration menu) ........ 30

9 Diagnostics and

troubleshooting ............... 33

9.1 Trouble shooting instructions ......... 33

9.2 Trouble shooting instructions ......... 33

9.3 Diagnostic messages ................ 34

10 Maintenance .................. 37

10.1 Cleaning the housing ................ 37

11 Repairs ......................... 38

11.1 Return ............................ 38

11.2 Disposal ........................... 38

12 Accessories .................... 39

12.1 Calibration solutions ................ 39

13 Technical data ................. 39

Index ................................. 46

Document information Smartec CLD18

4 Endress+Hauser

1 Document information

1.1 Warnings

Structure of information Meaning

LDANGER

Causes (/consequences)

Consequences of non-compliance (if

applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation will result in a fatal or serious injury.

LWARNING

Causes (/consequences)

Consequences of non-compliance (if

applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation can result in a fatal or serious injury.

LCAUTION

Causes (/consequences)

Consequences of non-compliance (if

applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or more serious injuries.

NOTICE

Cause/situation

Consequences of non-compliance (if

applicable)

‣Action/note

This symbol alerts you to situations which may result in damage to property.

1.2 Symbols used

Symbol Meaning

Additional information, tips

Permitted or recommended

Not permitted or not recommended

Reference to device documentation

Reference to page

Reference to graphic

 Result of a step

1.3 Symbols at the device

Symbol Meaning

Reference to device documentation

Smartec CLD18 Basic safety instructions

Endress+Hauser 5

2 Basic safety instructions

2.1 Requirements for the personnel

• Installation, commissioning, operation and maintenance of the measuring system may be

carried out only by specially trained technical personnel.

• The technical personnel must be authorized by the plant operator to carry out the specified

activities.

• The electrical connection may be performed only by an electrical technician.

• The technical personnel must have read and understood these Operating Instructions and

must follow the instructions contained therein.

• Measuring point faults may be repaired only by authorized and specially trained personnel.

Repairs not described in the Operating Instructions provided may only be carried out

directly by the manufacturer or by the service organization.

2.2 Designated use

The compact measuring system is used for inductive conductivity measurement in liquids with

medium to high conductivity.

Use of the device for any purpose other than that described, poses a threat to the safety of

people and of the entire measuring system and is therefore not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

NOTICE

Non-designated use

Incorrect measurements, malfunctions and even measuring point failure could result

‣Only use the product in accordance with the product specifications.

‣Pay particular attention to the technical data on the nameplate.

2.3 Occupational safety

As the user, you are responsible for complying with the following safety conditions:

• Installation guidelines

• Local standards and regulations

Electromagnetic compatibility

• The product has been tested for electromagnetic compatibility in accordance with the

applicable European standards for industrial applications.

• The electromagnetic compatibility indicated applies only to a product that has been

connected in accordance with these Operating Instructions.

Basic safety instructions Smartec CLD18

6 Endress+Hauser

2.4 Operational safety

1. Before commissioning the entire measuring point, verify that all connections are

correct. Ensure that electrical cables and hose connections are undamaged.

2. Do not operate damaged products, and safeguard them to ensure that they are not

operated inadvertently. Label the damaged product as defective.

3. If faults cannot be rectified:

Take the products out of operation and safeguard them to ensure that they are not

operated inadvertently.

2.5 Product safety

The product is designed to meet state-of-the-art safety requirements, has been tested, and

left the factory in a condition in which it is safe to operate. The relevant regulations and

European standards have been observed.

We only provide a warranty if the device is installed and used as described in the Operating

Instructions. The device is equipped with security mechanisms to protect it against any

inadvertent changes to the device settings.

IT security measures in line with operators' security standards and designed to provide

additional protection for the device and device data transfer must be implemented by the

operators themselves.

Smartec CLD18 Incoming acceptance and product identification

Endress+Hauser 7

3 Incoming acceptance and product identification

3.1 Incoming acceptance

1. Verify that the packaging is undamaged.

 Notify your supplier of any damage to the packaging.

Keep the damaged packaging until the matter has been settled.

2. Verify that the contents are undamaged.

 Notify your supplier of any damage to the delivery contents.

Keep the damaged products until the matter has been settled.

3. Check the delivery for completeness.

 Check it against the delivery papers and your order.

4. Pack the product for storage and transportation in such a way that it is protected

against impact and moisture.

 The original packaging offers the best protection.

The permitted ambient conditions must be observed (see "Technical data").

If you have any questions, please contact your supplier or your local sales center.

3.2 Product identification

3.2.1 Nameplate

The nameplate provides you with the following information on your device:

• Manufacturer identification

• Order code

• Extended order code

• Serial number

• Firmware version

• Ambient and process conditions

• Input and output values

• Measuring range

• Safety information and warnings

• Protection class

‣Compare the data on the nameplate with your order.

Incoming acceptance and product identification Smartec CLD18

8 Endress+Hauser

3.2.2 Product identification

Product page

www.endress.com/CLD18

Interpreting the order code

The order code and serial number of your product can be found in the following locations:

• On the nameplate

• In the delivery papers

Obtaining information on the product

1. Go to the product page for your product on the Internet.

2. At the bottom of the page, select the "Online Tools" link followed by "Check your device

features".

 An additional window opens.

3. Enter the order code from the nameplate into the search field, and then select "Show

details".

 You will receive information on each feature (selected option) of the order code.

3.3 Scope of delivery

The delivery comprises:

• A Smartec CLD18 measuring system in the version ordered

• Operating Instructions BA01149C/07/EN

Smartec CLD18 Incoming acceptance and product identification

Endress+Hauser 9

3.4 Certificates and approvals

3.4.1 Declaration of Conformity

The product meets the requirements of the harmonized European standards. As such, it

complies with the legal specifications of the EC directives. The manufacturer confirms

successful testing of the product by affixing to it the  mark.

3.4.2 Hygiene

FDA

All materials in contact with the product are FDA-listed materials (apart from the PVC process

connections).

EHEDG

Certified cleanability according to EHEDG Type EL Class I.

When using the sensor in hygienic applications, please note that the cleanability of the

sensor also depends on the way the sensor is installed. To install the sensor in a pipe, use

the appropriate and EHEDG-certified flow vessels for the particular process connection.

3-A

Certified according to 3-A Standard 74- ("3-A Sanitary Standards for Sensor and Sensor

Fittings and Connections Used on Milk and Milk Products Equipment").

EC Regulation No. 1935/2004

The sensor meets the requirements of EC Regulation No. 1935/2004 on materials and articles

intended to come into contact with food.

3.4.3 Pressure approval

Canadian pressure approval for pipes according to ASME B31.3

Product description Smartec CLD18

10 Endress+Hauser

4 Product description

A0019184

 1 Elements

1 Temperature sensor

2 Process connection

3 Leakage hole

4 Removable housing cover

5 Window for display

6 Cable glands

7 Flow opening of sensor

Otros manuales para Smartec CLD18

Tabla de contenidos

Otros manuales de Instrumento de medición de Endress+Hauser

Endress+Hauser

Endress+Hauser StamoLys CA 71 HY Manual de usuario

Endress+Hauser

Endress+Hauser Proline t-mass 65 Manual de usuario

Endress+Hauser

Endress+Hauser SpectraSensors SS2100i-1 Guía del usuario

Endress+Hauser

Endress+Hauser prosonic flow 92 Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar M PMP51 Manual

Endress+Hauser

Endress+Hauser Proline Prowirl 73 Manual de usuario

Endress+Hauser

Endress+Hauser Liquiline Control CDC90 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Manual de usuario

Endress+Hauser

Endress+Hauser Analytik Jena multi EA 5000 Manual de usuario

Endress+Hauser

Endress+Hauser Prothermo NMT532 Manual de usuario

Endress+Hauser

Endress+Hauser Silopilot FMM50 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Especificaciones técnicas

Endress+Hauser

Endress+Hauser FQG60 Manual del operador

Endress+Hauser

Endress+Hauser Levelflex M Especificaciones técnicas

Endress+Hauser

Endress+Hauser Cerabar PMC71B Especificaciones técnicas

Endress+Hauser

Endress+Hauser ria45 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Liquiline System CA80NO Manual de usuario

Endress+Hauser

Endress+Hauser PROline promag 23 Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex FMP56 Manual de usuario

Endress+Hauser

Endress+Hauser SpectraSensors J22 TDLAS Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic M FMU44 Manual de usuario

Endress+Hauser

Endress+Hauser nivotester FTC 420 Manual de usuario

Endress+Hauser

Endress+Hauser RID16 Manual de usuario

Endress+Hauser

Endress+Hauser StamoLys CA 71 CU Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario

R&S

R&S ZPH Manual de usuario